AT Pro Manual
Table Of Contents
- 1533200 AT_Pro_US_C 1
- 1533200 AT_Pro_US_C 2
- 1533200 AT_Pro_US_C 3
- 1533200 AT_Pro_US_C 4
- 1533200 AT_Pro_US_C 5
- 1533200 AT_Pro_US_C 6
- 1533200 AT_Pro_US_C 7
- 1533200 AT_Pro_US_C 8
- 1533200 AT_Pro_US_C 9
- 1533200 AT_Pro_US_C 10
- 1533200 AT_Pro_US_C 11
- 1533200 AT_Pro_US_C 12
- 1533200 AT_Pro_US_C 13
- 1533200 AT_Pro_US_C 14
- 1533200 AT_Pro_US_C 15
- 1533200 AT_Pro_US_C 16
- 1533200 AT_Pro_US_C 17
- 1533200 AT_Pro_US_C 18
- 1533200 AT_Pro_US_C 19
- 1533200 AT_Pro_US_C 20
- 1533200 AT_Pro_US_C 21
- 1533200 AT_Pro_US_C 22
- 1533200 AT_Pro_US_C 23
- 1533200 AT_Pro_US_C 24
- 1533200 AT_Pro_US_C 25
- 1533200 AT_Pro_US_C 26
- 1533200 AT_Pro_US_C 27
- 1533200 AT_Pro_US_C 28
- 1533200 AT_Pro_US_C 29
- 1533200 AT_Pro_US_C 30
- 1533200 AT_Pro_US_C 31
4
Garrett Metal Detectors AT Pro™
5
AT Pro CONTROL PANEL QUICk START GUIDE
1. Install batteries.
The AT Pro operates with four (4) AA batteries which are
already installed by Garrett.
2. Power ON.
Press and release the ON / OFF Power button. The AT Pro
powers on in the last mode used and is ready to search.
(Factory default mode is Coins.)
3. Select Mode.
Use the Mode Pushbutton to select a different detection
mode, when desired.
4. Adjust settings.
Adjust Sensitivity or Discrimination settings, if desired.
5. Begin scanning.
Lower the searchcoil to 1 to 2 inches above the ground and
scan the coil left and right at approximately 3ft/second.
Battery Level
Indicator
ELIM and NOTCH DISC
Pushbuttons
Use NOTCH DISC (+) or (-) to select
a cursor. Then use ELIM button to set
its discrimination on or off.
SENSITIVITY
Pushbutton
increases or decreases sensitivity.
ON / OFF Power: hold 1 second
to turn power on/off.
MODE: push quickly to toggle
between detection modes.
RESET: hold 5 seconds to restore
factory settings.
Coin Depth
Indicator
indicates depth of
coin-sized target.
Mode
Indicator
Target ID
Legend
indicates
metal types.
Lower Scale
indicates notch
discrimination pattern.
Target ID
Cursor
indicates
probable
target identity.
Digital
Target ID
(also shows
ground balance
settings while in
GND-BAL mode.)
PINPOINT /
Frequency
Adjust
Pushbutton
Press and hold to
pinpoint or use with
SENSITIVITY (+)
or (-) to change
frequency.
Sensitivity
Setting
High Resolution
Iron Discrimination
indicates level of iron
discrimination selected.
Iron Disc
Pushbutton
Use (+) or (-) to change
iron discrimination
level.
Iron Audio
Use to hear
discriminated
iron.
GROUND BALANCE
Pushbutton
Press and hold for fast auto
ground balance or use with
NOTCH DISC (+) or (-) for
manual ground balance.