Corporate Headquarters GarrettCom, Inc. Magnum 6K25e 47823 Westinghouse Dr. Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com Gigabit Fiber Switch email support@garrettcom.com Hardware Installation and User Guide www . GarrettCom . com www . GarrettCom .
Magnum Gigabit Fiber Switch Installation and User Guide (10/07) Magnum™ 6K25e Managed Fiber Switch Hardware Installation and User Guide Part #: 84-00163Z (Rev. A) Trademarks Ethernet is a trademark of Xerox Corporation NEBS is a trademark of Telcordia Technologies UL is a registered trademark of Underwriters Laboratories GarrettCom, Magnum and Personal Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc.
Magnum Gigabit Fiber Switch Installation and User Guide (10/07) Contacting GarrettCom, Inc Please use the mailing address, phone and fax numbers and email address listed GarrettCom, Inc. below: 47823 Westinghouse Dr. Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com email support@garrettcom.
Magnum Gigabit Fiber Switch Installation and User Guide (10/07) TABLE OF CONTENTS Page 1.0 SPECIFICATIONS ................................................................................ 1 1.1 Technical Specifications....................................................................... 1 1.2 Ordering Information ........................................................................... 4 2.0 INTRODUCTION.................................................................................. 7 2.
Magnum Gigabit Fiber Switch Installation and User Guide (10/07) 5.0 6K25E MANAGED FIBER SWITCH PORT MODULES .................... 42 5.1 Inspecting the Package and Product................................................... 43 5.2 6KPM Module Description ................................................................ 43 5.2.1 6KP6-RJMST, multi-mode FX-ST “twist lock” Module ........... 44 5.2.1a 6KP6-RJ10ST FX-ST “twist lock” Combo Module .................. 44 5.2.1b 6KP4-F10ST, “twist lock” Module .......
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) The Magnum Line INDUSTRIAL NETWORKING PRODUCTS "DESIGNED AND MANUFACTURED IN THE USA" OVERVIEW GarrettCom, Inc. offers the premium-quality Magnum™ line of INDUSTRIAL conectivity products with industry-standard functionality and built-in fiber configurability. Magnum products are designed for use in demanding Industrial Grade, Carrier Class, POWER UTILITY and OEM applications where reliability is a primary consideration.
Magnum 6K25e Gigabit Fiber Switch 1.0 1.1 Installation and User Guide (10/07) SPECIFICATIONS Technical Specifications Performance Filtering / Forwarding Rate: Ethernet:14,880 pps Fast Ethernet: 148,800 pps Gigabit Ethernet: 1, 488,000 pps Switching Processing Type: Store and Forward with IEEE 802.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Fiber Multi-mode connector types supported: Fiber Port, ST-type (twist-lock):Fiber multi-mode, 10Mb 10BASE-FL Fiber Port, MTRJ-type (plug-in):SFF Fiber multi-mode100BASE-FX Fiber Port, SC-type (snap-in):Fiber optic multi-mode, 100BASE-FX Fiber Port, ST-type (twist-lock): Fiber optic m.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) For DC internal power supplies at –48VDC, 24VDC and 125VDC, including Dual Source options (for continuity of operation when either of the DC input sources are interrupted), see Appendices B and C. Per-port MDI or MDIX on RJ-45 The copper daughter board has MDI-MDIX Auto-crossover on all the RJ-45 ports., and eliminate the use of cross-over cable between the devices.
Magnum 6K25e Gigabit Fiber Switch 1.2 Installation and User Guide (10/07) Ordering Information Magnum Managed Fiber Switch MODEL DESCRIPTION Magnum 6K25e Magnum 6K25e Managed Fiber Switch, base unit. May be configured with a selection of 10/100/1000 6K25e fiber and copper port connector types, 25 total ports max. Wire speed filtering and forwarding across all ports, 802.3x flow control, 802.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) For Gigabit module configuration options GBPM-COTX One slot Gigabit 6K module for 6K25e Switches, uses one 6K25e slot and provides one GBIC open transceiver port for a user-selectable GBIC transceiver module GBIC-SXSC GBIC transceiver module for use in GBPM-xOTX, one 1000BASE-SX port with mm SC fiber connector GBIC-LXSC10 GBIC transceiver module for use in GBPM-xOTX, one 1000BASELX/LH port with 1310nm sgl.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) New P6KP8-452SLC “6+2” port PoE module for 6ks with 48vdc PS, w/four PoE power source and four 100 Mb 15km Sm FX LC connectors New P6KP6-RJMST “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power source and two 100 Mb 2km mm FX ST connectors New P6KP6-RJMSC “4+2” port PoE module for 6ks with 48vdc PS, w/four PoE power source and two 100 Mb 2km mm FX SC connectors New P6KP6-RJSSC “4+2” port PoE module for 6ks with 48vdc PS, w/fo
Magnum 6K25e Gigabit Fiber Switch 2.0 2.1 Installation and User Guide (10/07) Introduction Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product; notify the carrier of any damage that you believe occurred during shipment or delivery. Inspect the contents of this package for any signs of damage and ensure that the items listed below are included.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Gigabit port in the same unit. This flexibility is achieved via a family of 6K25e port modules for copper and fiber-built-in (emphasizing Small Form Factor fiber for high fiber port density), 6-port modules for fiber and RJ-45 combinations, and 1Gb port module selections using GBICs.
Magnum 6K25e Gigabit Fiber Switch 2.2.1 Installation and User Guide (10/07) Magnum 6K25e and 6K25eR chassis The Magnum 6K25e is a 19” rack-mountable Ethernet Switch with three eight-port slots (A, B, and C) and one Gb-only slot (D) for configuration flexibility. Slots A, B and C may be configured with any of a large selection of fiber and copper port types and combinations of types, typically eight ports per module, but sometimes 6 or 4 ports or even one Gb port.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) In an eight-port SFF fiber port module, all of the fiber ports are of the same speed (100Mb), mode, and connector type. Models are available with Small Form Factor (SFF) are multi-mode MT-RJ or LC1 3 5 7 AC ACT F/H AC F/H ACT F/H LK LK 2 4 LK 6 AC ACT F/H ACT LK LK 2 4 LC-type connectors.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) eliminate the need of cross-over cable. On the model 6K8-RJ45 module, there are four LEDs for each port, two in the connector and two separate. The LK (Link) LED indicates “ready for operation” on that port when lit. The blinking ACT (Activity) LED indicates receiving Activity on that port when lit. The 10/100 LED indicates operation at 100Mb speed when ON and at 10 Mb speed when OFF (when autonegotiation is not disabled).
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) ordering information Sec.1.2. for all the various PI6K PoE modules option. The LEDs on 6KP8-RJ45- PoE module are slightly different compared to regular (non-PoE) RJ-45 modules as shown in Fig 2. When the PoE port is in use, the PoE LED is ON when connected properly to a 803.af compliant PD device on that port. When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data traffic is not affected by PoE.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) (MDIX) feature to eliminate the use of cross-over cable, and the two fiber ports operate at 100Mbps full-duplex (default). User mode control per port through the MNS software is also the same. On Magnum “4+2” Combo modules, there are four LED’s for each RJ-45 port, which indicate status the same as described for the 6K8-RJ45 in Section 2.2.3 above.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) fiber modules except for the 10Mb speed. For ports numbering, ports 1, 2, 5, 6 are present, ports 3, 4. 7, 8 are not present. The default setup on the 10Mb fiber module is half-duplex, which allows the Magnum 6K25e Switch to connect to any 10Mb hub or media converter or almost any other device with a 10Mb fiber Ethernet port. User mode control per port through the MNS software is the same as the other 6K25e modules.
Magnum 6K25e Gigabit Fiber Switch 2.2.9 Installation and User Guide (10/07) Packet Prioritization, 802.1p QOS Quality of Service means providing consistent predictable data delivery to users from datagram paths that go all across a network. As a LAN device, the Magnum 6K25e can do its part to prevent any QOS degradation while it is handling Ethernet traffic through its ports and buffers. The Magnum 6K25e switching hardware supports the IEEE 802.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) its free buffer queue space is low, the Switch prevents more frames from entering by forcing a collision signal on all receiving half-duplex ports in order to stop incoming traffic. 2.2.11 Managed Network Software (MNS-6K ) for Magnum 6K25e-Series Magnum 6K25e’s come with Rel3.
Magnum 6K25e Gigabit Fiber Switch 2.3 Installation and User Guide (10/07) Features and Benefits Managed switching for high performance Ethernet LANs Magnum 6K25e Switches provide non-blocking (all ports can run at full speed at once) performance with standard Managed Networks Software (MNS-6K) included. They are typically used in LAN traffic centers with eight Gigabit ports or 16 to 24 100Mb ports and one or 2 Gigabit ports for backbone connections, where managed network services are desired.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) client for time-of-day; BootP and DHCP client for IP configuring, and password security. Supplied and updated via Internet and GCI FTP Server. RJ-45 ports are MDI/MDIX supported The RJ-45 modules are equipped with MDI/MDIX capability to eliminate the use of cross-over cable. The Auto-MDIX capability allow the Magnum 6K25e to cascade any Hub, switches or media converters with normal straight cable.
Magnum 6K25e Gigabit Fiber Switch 2.4 Installation and User Guide (10/07) Applications Magnum 6K25e Fiber Switches offer high performance and modularity. They provide the flexibility of 100Mbps fiber and copper ports as well as Gigabit ports, with industry-standard LAN management software.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) The Magnum 625e Managed Switch equipped with copper and optional dual Gigabit fiber ports on modular slots provide an economical and seamless solution to the requirements. The user-configurable Magnum 6K25e provides an extra boost to the network requirements by providing copper/fiber media along with the higher bandwidth 10/100 15 F/H 10/100 support of 10/100 and 1000Mb.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) The Dual Giga option on each of the two slot add 4 Gigaport to handle the bandwidth requirement and 16 10/100 RJ-45 ports to feed the other needs of equipment connected to the 6K25e. The robust Tag based vlan feature will able to segregates different ports belong to one group and provide an effective solution for bandwidth. The SNMP option and secure web based will allow the remote capability and monitoring the network securely.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Locate an AC receptacle that is within six feet (2 meters) of the intended Magnum 6K25e site. The rugged metal case of the Magnum 6K25e will normally protect it from accidental damage in a lab or workplace setting. Maintain an open view of the front to visually monitor the status LEDs. Keep an open area around the unit so that cooling can occur from the small fan on the left side, while the unit is in operation. See figure below. 3.
Magnum 6K25e Gigabit Fiber Switch 3. 4. 5. 3.2.2 Installation and User Guide (10/07) Connect the Transmit (TX) port (light colored post) on the Magnum PM to the Receive (RX) port of the remote device. Begin with the color-coded strand of the cable for this first TX-to-RX connection. Connect the Receive (RX) port (dark colored post on the PM) to the Transmit (TX) port of the remote device. Use the non-color coded fiber strand for this.
Magnum 6K25e Gigabit Fiber Switch 1. 2. 3. Installation and User Guide (10/07) The following procedure describes how to connect a 10BASE-T or 100BASETX twisted pair segment to the RJ-45 port. The procedure is the same for both unshielded and shielded twisted pair cables. Using standard twisted pair media, insert either end of the cable with an RJ-45 plug into the RJ-45 connector of the port. Note that, even though the connector is shielded, either unshielded or shielded cables and wiring may be used.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) illuminated when the unit is powered and proper connection is established 3.2.6 Gigabit SFP (Small Form-factor Pluggable) Optical Transceivers The small form-factor pluggable (SFP) is a compact optical transceiver used in optical communications for both telecommunication and data communications applications. Due to its compact, hot pluggable characteristics, SFPs are becoming a very popular choice for various applications.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) The various SFPs transceivers supported by GarrettCom 6K25e, D slot are- Module Model# Gigabit Slot D only for 6K25e 6KE-2GSFP 2 SFP 6KE-2GCUSFP 1 CU, 1SFP 6KE-2GCU/1GCU 2 CU / 1 CU 6KE-1GSFP 1 SFP GBPM-DOTX 1 GBIC Gb SFP fiber optic transceivers SFP-SX Gb SX, 850nm wavelength, 500 m distance SFP-LX10 Gb LX, 1310nm wavelength, 10km dist SFP-LX25 Gb LX, 1310nm wavelength, 25km distance SFP-ZX40 Gb ZX, 1550nm wavelengt
Magnum 6K25e Gigabit Fiber Switch 3.3.1 Installation and User Guide (10/07) Rack-mounting (for 19” RETMA racks), regular Magnum 6K25es Installation of a Magnum 6K25e Fiber Switch in a 19” rack is a simple procedure. The units are 1U (1.70”) high. When properly installed, the front-mounted LED status indicators should be in plain view and easy to read. Rack-mount installation requires special 19” rack-mounted brackets and screws (included with each Magnum 6K25e unit).
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) package, along with the necessary screws for attaching the brackets to the sides of the Magnum Switch unit. They must be ordered as line items. 3.3.2 Rack-mounting, Reverse version of the Magnum 6K25es The optional Reverse Magnum 6K25e Model has all of the cabling (Ethernet cabling, power cabling and console port cabling) connectors in the rear, and the status LEDs in the front.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Ethernet cabling, there is no need to power down the unit. Individual segments can be connected or disconnected without concern for AC power-related problems or damage to the unit.
Magnum 6K25e Gigabit Fiber Switch 3.5 Installation and User Guide (10/07) 6K25e Port Module (6KPM) Installation The Magnum 6K25e Switches are normally received from the factory with all required 6KPM modules installed. There may be situations where 6KPM cards need to be added or replaced. In cases where additional 6KPM cards are needed, the faceplate for an available front-mounted slot must be removed. The following procedure describes this operation. 3.5.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) assembled together with the help of 22 Philips-head screws. There are 7 screws located on the front-bottom and rear-top of the unit and four screws each on the sides. Remove these screws. Once these are removed, the top cover is easily lifted off the chassis base. When the chassis top cover has been removed, the interior of the unit is exposed. Figure 3.5.1a: Removing Chassis Cover Caution: Be careful not to disturb the power supply.
Magnum 6K25e Gigabit Fiber Switch 3.5.2 Installation and User Guide (10/07) Installing 6KPM Cards in the Magnum 6K25e Up to four front-mounted 6KPM cards may be installed in one Magnum 6K25e Managed Fiber Switch unit. Follow these steps to install a 6KPM. Step 1. Remove top chassis cover. See procedure in Section 3.5.1 above. Step 2. Placed Granddaughter board (as shown in fig. 3.5.2a and 3.5.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Fig. 3.5.2c Daughter Board, top view of version for 4 copper 10/100 ports. Port# 1 Uplink Can be configured as uplink (x) crossed ports for cascading as shown in the Fig. Fig 3.5.2d Daughter Board shown upside down with two male latch connectors Step 4.
Magnum 6K25e Gigabit Fiber Switch Step 5. Installation and User Guide (10/07) Once the latching connectors are aligned properly and the mounting holes are aligned with stand offs then press slowly and firmly with two fingers (as shown below in Fig. 3.5.2f) on the top of the latching connectors until the connectors latched up securely. Figure 3.5.2f: Securely latching up 6KPM Cards into a Magnum 6K25e NOTE: All 6KPM slots need not be filled in order for the Magnum 6K25e unit to be operational.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) brackets and 6 #256 flat head screws. The brackets and screws have been installed inside of the top cover as shown in Fig. 3.5.2h. Fig. 3.5.2h Inside view of chassis cover (from the rear), showing the front panel screen plates installed inside the chassis cover using brackets and screws Step 8. Once all 6KPM cards have been installed (including faceplates for empty slots), the chassis cover should be replaced.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) the 4 screws and bracket while holding it down firmly. Figure 3.5.3a: Top View - 6 retaining s crews shown by arrows Step 3. Remove 6KPM Card Carefully and gently pull out the daughter board from the latching connectors, using both hands, gripping the board near the latch-up connectors as shown in Fig. 3.5.3b . If the now empty slot is to remain unused, be sure to install a 6KPM-BLNK face plate cover. Figure 3.5.
Magnum 6K25e Gigabit Fiber Switch 3.6.1 Installation and User Guide (10/07) RS-232 (DB-9) Console Com port (Serial port) pin assignments. Pin 1 Pin 5 DB-9 (Console port connector) Pin Signal 1 2 3 4 5 6-9 CD RXD TXD open GND open Description Carrier detect (not used) Receive Data (input) Transmit Data (output) not used Signal Ground not used The above provided information enables a managed station( a PC or Console terminal) to connect directly to the switch using a straight through cable.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Magnum 6K25e units are plug-and-play devices. There is no software configuring necessary to be done for basic operation at installation or for maintenance. The only hardware configuration settings are user options for an UP-LINK Switch (resides inside the unit) on the 6K8-RJ45. Optional Half / Full duplex mode and 10 or 100Mbps selection for the switched ports must be configured through MNS software per unit as per the requirement.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) on the inside of the unit on the port module board next to the RJ45 port # 1 which it controls. It enables the port’s cable to be cascaded (X) to a 10/100Mb repeater or switching hub in the network. The manual Up-link switch position is configured as (=) position as default factory setting, where used for all-copper module or combo modules. 4.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) arrive at the highest order mode that both devices can support at that time. (Since autonegotiation is potentially an externally controlled process, the original “highest order mode” result can change at any time depending on network changes that may occur).
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Magnum 6K25e Switches implement the 802.3x flow control (non-blocking) on Full-Duplex ports, which provides for a “PAUSE” packet to be transmitted to the sender when the packet buffer is nearly filled and there is danger of lost packets. The transmitting device is commanded to stop transmitting into the 6K25e Switch port for sufficient time to let the Switch reduce the buffer space used.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) 6KPM- 100Mb Multi2 1300 62.5/125 -20 FX mode (0.4) 50/125 -23.5 100Mb Single- 18+ -15 6KPM-SSC FX mode (0.4) 1300 9/125 100Mb Single- 40 6KPM-5 FX mode (0.4) 1300 9/125 SSCL -31 -31 9.0 5.5 3.0 2.0 14 12 5 4 -31 14 28 17.5 35 -34 29 58 32.5 65 6KPMMTRJ 100Mb Multi2 1300 62.5/125 -20 FX mode (0.4) 50/125 -23.5 -31 -31 9.0 5.5 3.0 2.0 15.8 12.2 5.5 4.0 6KPMMLC 2 100Mb Multi1300 62.5/125 FX mode (0.
Magnum 6K25e Gigabit Fiber Switch 5.1 Installation and User Guide (10/07) Inspecting the Package and Product This section applies only to PMs shipped as separate items, i.e., 6K25e PMs not factory installed in a Magnum 6K25e PM slot. Examine the shipping container for obvious damage prior to installing a 6K25e PM; notify the carrier of any damage you believe occurred during shipment or delivery.
Magnum 6K25e Gigabit Fiber Switch 5.2.1 Installation and User Guide (10/07) 6KP6-RJMST, 4@10/100Mbps RJ-45 and 2@100Mb multi-mode FX-ST “twist lock” Combo Module The Magnum 6KP6-RJMST is a combo 6 port module of RJ-45’s at 10/100Mbps and fiber optic ports at 100MB. The Combo module is equipped with dualmode ST-type connectors and dual speed copper ports.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) The Magnum 6KP4-F10ST 6KP4-RJ10MST, 4 Port@ 10Mb ST Fiber Port is a 10Mb multi-mode 2 fiber module with 4 STFiber ports. All four fiber ACT F/H ports are ST connectors and configured as 10Mb ACT F/H 1 TX LK RX 3 ACT F/H Half-duplex by default.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) fiber ports. Whereas the 100Mb ST module allow to connect the 100Mb demand of Switch devices. It supports distances according to the 10Base-FL standard i.e, 2Km distance for multi-mode fiber. (Single-mode for 10Km distance may be available as a special order).
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) The 6KP6-RJSSC, when installed in a Magnum 6K25e Switch operates on copper at the 100m distance. The Fiber is single-mode and cable lengths can be as much as 25+ Km (see Power Budget, Section 4.5) Each port has an Activity (ACT) LED indicating packets being received, a Link (LK) LED that indicates proper connectivity with the remote device when lit, and a FDX/HDX LED to indicate full-duplex mode when lit (or half-duplex when off).
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) proper connectivity with the remote device when lit, and a FDX/HDX LED indicating full-duplex mode when lit (or half-duplex when off). The 10/100 LED indicates the speed for the copper port, which is 10Mbps when the LED is ON and 10 Mb when the LED is OFF. 5.2.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Fiber connector supports the standard fiber optic distance limit of 2Km at Full and Halfduplex both. The functionality of this 100BASE-FX multi-mode 4 port module is essentially the same as the ST and SC-types. It has the same LEDs per port indicating port activity (ACT), Link (LK), and FDX or HDX operation 5.2.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) one housing that cannot be improperly inserted. Each port has an Activity (ACT) LED indicating packets being received, a Link (LK) LED indicating proper connectivity with the remote device when lit, and a FDX/HDX LED indicating full-duplex mode when lit (or half-duplex when off). 5.2.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Crossover (MDI-X) switch, which controls all ports for cascaded connection. This feature eliminates the need for a special twisted pair crossover cable when connecting to a hub or another switch.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) The LEDs on 6KP8-RJ45- PoE module are slightly different compared to regular (non-PoE) RJ-45 modules as shown in Fig 2. When the PoE port is in use, the PoE LED is ON when connected properly to a 803.af compliant PD device on that port. When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data traffic is not affected by PoE.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data traffic is not affected by PoE. LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK/ACT, as shown in the diagram. PoE LEDs Summary • For PoE devices, each RJ-45 PoE port supports only 802.3af complaint devices. The PoE LED is ON when the attached PD is drawing power from the port.
Magnum 6K25e Gigabit Fiber Switch The Magnum 6KP8- Installation and User Guide (10/07) 6KP8V 6 Port@ 10/100Mbps 45SLC eight port Module is a & 2 port @ 100Mbps Single-Mode Fiber port (LC) 2 combo module with copper and fiber (Small Form Factor) LC type 1 3 4 L 6KP8-45-2SLC AC F/H 10/100 The small size of LC connectors 1 5 10/10 fiber ports. ACT F/H ACT give an advantage of placing more F/H ports on one module.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Each port has an Activity (ACT) LED indicating packets being received and a link (LK) LED indicating proper connectivity with the remote device when lit. 5.2.14 6KM-BLNK The 6KM-BLNK is a blank face plate or cover plate that must be installed in any empty 6K25e PM slot to maintain proper cooling air flow, safety, etc. Two screws underneath the front panel hold the 6KM-BLNK in place. 6.
Magnum 6K25e Gigabit Fiber Switch 4. Installation and User Guide (10/07) If the problem is isolated to a network device other than the Magnum 6K25e Switch product, it is recommended that the problem device be replaced with a known good device. Verify whether or not the problem is corrected. If not, go to Step 5 below. If the problem is corrected, the Magnum 6K25e Switch and its associated cables are functioning properly. 5.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) GarrettCom will carefully test and evaluate all returned products, will repair products that are under warranty at no charge, and will return the warranty-repaired units to the sender with shipping charges prepaid (see Warranty Information, Appendix A, for complete details). However, if the problem or condition causing the return cannot be duplicated by GarrettCom, the unit will be returned as: No Problem Found.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) APPENDIX B : Internal DC Power Supply Options B1.0 SPECIFICATIONS FOR MAGNUM 6K25E SWITCHES, DC POWER Power Supply (Internal -48VDC Option) DC Power Connector: 3 terminals: “-“, “GND”, “+” Input Voltage: 36 - 70 VDC Power Consumption: Same as for AC models (see Section 1.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) other communication companies. In addition, many high availability equipment services, such as broadcasters, publishers, newspaper operations, brokerage firms and other facilities often use a battery backup system to maintain operations in the event of a power failure. It is also frequently used for computer system backup, management and operations monitoring equipment.
Magnum 6K25e Gigabit Fiber Switch B4.1 1. 2. 3. 4. 5. 6. B5.0 Installation and User Guide (10/07) UL Requirements for DC-powered units Minimum 18AWG cable for connection to a Centralized DC power source. Minimum 14AWG cable for connection to a earthing wiring. Use only with Listed 10 A circuit breaker provided in building installation. “Complies with FDA radiation performance standards, 21 CFR subchapter J.” or equivalent. Fastening torque of the lugs on the terminal block: 9 inch-pound max.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) With the exception of the dual DC input power connections and the power supply, all specifications and configuration options for the Magnum 6K25e -48VDC, 24VDC and 125VDC models with this Dual-Source option are identical to those listed in the Magnum 6K25e Fiber Switches Installation and User Guide, including Appendix B “Internal DC Power Supply Option” C2.
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) The -48VDC terminal block on the Magnum 6K25e Switch, as shown in Fig C5.0 is located on the right rear of the unit and A+ A- B- B+ is equipped with five (5) screw-down lead posts. If it is the reverse model it is located on the left rear. The primary terminals are identified as positive (A+), negative (A-), and the secondary 36-70VDC 36-70VDC GND power terminals as negative (B-), positive(B+).
Magnum 6K25e Gigabit Fiber Switch Installation and User Guide (10/07) Dual-Src24V for regular models with no ON-OFF switch Or Dual-Src125V-Switch for models with the ON-OFF switch C7.0 OPERATION Operation of the Dual-Source Magnum 6Ks-48VDC, 24VDC and 125VDC Switch models are identical to that of the standard models. www . GarrettCom .
