Corporate Headquarters GarrettCom, Inc. 47823 Westinghouse Dr. Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com Magnum 6K32T & 6K32TRC email support@garrettcom.com 6K32T 6K32TRC Managed Switch Installation and User Guide Hardware User Manual www . GarrettCom . com www . GarrettCom .
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07) Magnum™ 6K32T & 6K32TRC Managed Switch Hardware Installation and User Guide Part #: 84-00138 (Rev.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07) Contacting GarrettCom, Inc Please use the mailing address, phone and fax numbers and email address listed GarrettCom, Inc. below: 47823Westinghouse Dr. Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com email support@garrettcom.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07) TABLE OF CONTENTS.......................................................................... Page SPECIFICATIONS ................................................................................ 2 1.0 1.1 Technical Specifications....................................................................... 2 1.2 Ordering Information ........................................................................... 5 2.0 INTRODUCTION.................
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07) 4.4 Flow-control, IEEE 802.3x standard.................................................. 49 5.0 6K32T & 6K32TRC MANAGED SWITCH PORT MODULES..... 49 5.1 Inspecting the Package and Product................................................... 50 5.2 6KPM Module Description ................................................................ 50 5.2.1 6KP6-RJMST multi-mode FX-ST “twist lock” Module ............ 51 5.2.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide(05/07) The Magnum Line INDUSTRIAL NETWORKING PRODUCTS "DESIGNED AND MANUFACTURED IN THE USA" OVERVIEW GarrettCom, Inc. offers the premium-quality Magnum™ line of INDUSTRIAL conectivity products with industry-standard functionality and built-in fiber configurability. Magnum products are designed for use in demanding Industrial Grade, Carrier Class, POWER UTILITY and OEM applications where reliability is a primary consideration.
Magnum 6K32T & 6K32TRC Managed Switch 1.0 1.1 Installation and User Guide 05/07) SPECIFICATIONS Technical Specifications Performance Filtering / Forwarding Rate: Ethernet:14,880 pps Fast Ethernet: 148,800 pps Gigabit Ethernet: 1,488,000 pps Switching Processing Type: Store and Forward with IEEE 802.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Maximum Standard Gigabit Ethernet Segment Lengths: 1000BASE-T (CAT5E or higher is recommended) - 100 m 1000BASE-SX, full-duplex, multi-mode(62.5µm cable) - 220m 1000BASE-SX, full-duplex, multi-mode(50µm cable) - 550m 1000BASE-LX, full-duplex, single-mode(62.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Fuse Required – 2Amps 24VDC Power Input Voltage : 20 to 40VDC Fuse Required – 3Amps 125VDC Power and 100VDC Input Voltage : 88 to 300VDC Fuse Required – 1Amps Std. Terminal Block : “ -, GND, + ” Power Consumption: same as for AC models, see above Warning- All the fuse replacment must be replaced with same value.
Magnum 6K32T & 6K32TRC Managed Switch 1.2 Installation and User Guide 05/07) Ordering Information Magnum Managed Switch MODEL DESCRIPTION Magnum 6K32T 16 10/100 RJ-45 ports managed switch with two optional port modules (6K32T) which may be configured with a selection of 10/100/1000Mb fiber and copper connector types, max.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) 6KP8-45-2SLC “6+2” module, w/six RJ-45 ports and two 100Mb 15km sgl.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) 6K32T/6K32TRC PoE Modules with 48VDC Pass-Through Configuration options: only one A or B module slot of 6K-Series switch with 48VDC power input may be configured with a PoE Modules New P6KP8-RJ45 8 port PoE module for 6ks with 48vdc PS, w/eight PoE power source 10/100 auto-negotiating auto cross RJ-45 ports.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) New PI6KP8-45RJ “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power source and four 10/100 auto-negotiating auto cross RJ-45 ports New PI6KP8-45MT “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power source and four 100 Mb 2km mm FX MTRJ connectors New PI6KP8-45MLC “4+4” port PoE module for 6ks with 48vdc PS, w/four PoE power source and four 100 Mb 2km mm FX LC connectors New PI6KP8-45SLC “4+4” port PoE module for
Magnum 6K32T & 6K32TRC Managed Switch 2.0 2.1 Installation and User Guide 05/07) Introduction Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product; notify the carrier of any damage that you believe occurred during shipment or delivery. Inspect the contents of this package for any signs of damage and ensure that the items listed below are included.
Magnum 6K32T & 6K32TRC Managed Switch 2.2 Installation and User Guide 05/07) Product Description - Magnum 6K32TRC Managed Switch The IEC61850 complied and attributed with “green” environmentally friendly, Magnum 6K32TRC Managed Switch is specially designed with a convection cooled thermal design techniques to minimize heat generation to provide an efficient, highly reliable and secured Ethernet solution for heavy duty Industry, Power substations and temp-uncontrolled outdoor applications.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) LANs, it offers S-ring, RS-Ring, Link-Loss-Learn, STP and RSTP. Security features include SNMPv3, SSL/SSH, 802.1X, TACACS+, Port Security, and Tagged VLANs and a secured user friendly web based option. The IGMP feature for multicast traffic and streaming video application and IGMP-L2 mode feature is an attempt to provide a Layer 3 solution with 6K-Switches effectively and economically.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) managed networks software functionality with plenty of secure and remote monitoring features, all in convenient 1U rack-mount packages. 2.2.1a Magnum 6K32T Managed Switch Chassis The high port density and fan cooled Magnum 6K32T was designed for heavy duty Carrier class and Industrial applications that require high port density and secure devices which save in cost, rack space and running cool to provide reliable solutions.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) The Magnum 6K32T is preloaded with robust and intuitive MNS-6K Managed Network Software to handle industry-standard IEEE 802.1p QOS prioritization and nonblocking wire speed on all ports. It provides high performance switching services for both “smooth” streaming and “bursty” data traffic. For redundant LANs, it offers S-ring, RS-Ring, Link-Loss-Learn, STP and RSTP. Security features include SNMPv3, SSL/SSH, 802.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) In an eight-port SFF fiber port module, all of the fiber ports are of the same speed (100Mb), mode, and connector type. Models that are available with Small Form Factor (SFF) are multi-mode MT-RJ or LC-type connectors, and single-mode LC-type connectors. The 100Mb fiber eight-port modules for the Magnum 6K32T & 6K32TRC normally are set (factory default) to operate in full-duplex mode for best fiber distance and performance.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) On the model 6K8-RJ45 module, there are four LEDs for each port, two in the connector and two separate. The LK (Link) LED indicates “ready for operation” on that port when lit. The blinking ACT (Activity) LED indicates receiving Activity on that port when lit. The 10/100 LED indicates operation at 100Mb speed when ON and at 10 Mb speed when OFF (when autonegotiation is not disabled).
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) PoE LED is ON when connected properly to a 803.af compliant PD device on that port. When non-PoE devices are connected, the PoE LED is OFF. Operation of Ethernet data traffic is not affected by PoE. LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK/ACT, as shown in the diagram. 2.2.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) SC or single mode SC or Long Reach SC ports. For ports numbering, ports 1,3,5,7 are copper, ports 2 and 6 are fiber, ports 4 and 8 are not present. The four RJ-45 ports operate just like the 8-port copper module with auto-cross (MDIX) feature to eliminate the use of cross-over cable, and the two fiber ports operate at 100Mbps full-duplex (default). User mode control per port through the MNS software is also the same.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) 6K32TRC modules. The fiber ports support fiber cabling distances according to the 10BASE-FL standard, i.e., 2km distance for multi-mode fiber. (Single-mode for up to 10Km distance may be available as a special order configuration). 2.2.6 Gigabit (1000Mbps) port modules The Magnum 6K32T & 6K32TRC & 6K32’s offer wide options for Gigabit speed with multiple choices for the modular slot.
Magnum 6K32T & 6K32TRC Managed Switch 2.2.7 Installation and User Guide 05/07) Packet Prioritization, 802.1p QOS Quality of Service means providing consistent predictable data delivery to users from datagram paths that go all across a network. As a LAN device, the Magnum 6K32T & 6K32TRC can do its part to prevent any QOS degradation while it is handling Ethernet traffic through its ports and buffers. The Magnum 6K32T & 6K32TRC switching hardware supports the IEEE 802.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Another feature implemented in Magnum 6K32T & 6K32TRC Switches is a collision-based flow-control mechanism (when operating half-duplex only). When the Switch detects that its free buffer queue space is low, the Switch prevents more frames from entering by forcing a collision signal on all receiving half-duplex ports to stop incoming traffic. 2.2.
Magnum 6K32T & 6K32TRC Managed Switch 2.3 Installation and User Guide 05/07) Features and Benefits Managed switching for high performance Ethernet LANs Magnum 6K32T & 6K32TRC & 6K32TRC Switches provide non-blocking (all ports can run at full speed at once) performance with standard Managed Networks Software (MNS-6K) included. They are typically used in LAN traffic centers with 24 10/100Mb ports or one or two Gigabit ports for backbone connections where managed network services are desired.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) MNS-6K licensed Network Management Software included, S-Ring/RS-Ring optional Release 3.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) for each of them. The Magnum 6K32T’s VLAN capability can be configured in two types of virtual LANs; Port-based VLANs and Tag-based VLANs. In an office environment where departments such as Finance, Engineering, R&D, and Marketing need to each keep a secure LAN, the 6K32T’s VLAN feature will prevent traffic cross-over among traffic domains and thus keep sensitive data and information controlled.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) The Magnum 6K32T Managed Switch equipped with copper and optional dual Gigabit fiber ports on modular slots provide an economical and seamless solution to the requirements. The user-configurable Magnum 6K32T provides an extra boost to the network requirements by providing copper/fiber media along with the higher bandwidth support of 10/100 and 1000Mb. The user can utilize the SNMP feature equipped with VLAN, Port security, 802.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) 1 15 F/H 10 / 100 LK/ ACT F/H 2 4 6 8 10 12 14 16 1 15 F/H LK/ACT 10/100 F/H 2 4 6 8 10 12 14 16 15 1 F/H 10/1 00 LK/ ACT F/H 2 1 4 6 8 10 12 14 16 1 15 F/H 15 F/H LK/ACT 10/100 LK/ACT 10/100 F/H F/H 2 4 6 8 10 12 14 16 2 4 6 8 10 12 14 16 1 15 F/H 10/1 00 LK/ACT F/H 2 1 4 6 8 10 12 14 16 15 F/H 10/ 100 LK/ ACT F/H 2 1 15 4 6 8 10 12 14 16 1
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Equipped with IGMP-L2 mode enhanced features allow the Magnum 6K32TRC to meet the fastest growing application of video monitoring or video surveillance demand of industry and provide an economical and effective solution to meet that expectation.
Magnum 6K32T & 6K32TRC Managed Switch 3.0 Installation and User Guide 05/07) Installation Before installing the equipment, it is necessary to take the following precautions: 1.) If the equipment is mounted in an enclosed or multiple rack assembly, the environmental temperature around the equipment must be less than or equal to 55C FOR 6K32T and 60C for 6K32TRC. 2.) If the equipment is mounted in an enclosed or multiple rack assembly, adequate airflow must be maintained for proper and safe operation. 3.
Magnum 6K32T & 6K32TRC Managed Switch 3.2 Installation and User Guide 05/07) Connecting Ethernet Media The Magnum 6K32T & 6K32TRC Switches are specifically designed to support all standard Ethernet media types within a single Switch unit. This is accomplished by using a family of different port Modules which can be individually selected and configured per-port. See Section 2.4 for a description of the PMs. The various media types supported along with the corresponding IEEE 802.3 and 802.
Magnum 6K32T & 6K32TRC Managed Switch 3.2.2 Installation and User Guide 05/07) Connecting Fiber Optic SC-type, "Snap-In" The following procedure applies to installations using a PM with SC-type fiber connectors, i.e., using 6K-MSC or 6K-SSC (single mode) etc. When connecting fiber media to SC connectors, simply snap the two square male connectors into the SC female jacks of the 6KPM until they click and are secure. 3.2.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) NOTE: for Power Substations: In support of the IEEE 1613 Class 2 standard, GCI advises that, for substation applications, the RJ-45 ports are intended for connectivity to other communication equipment such as routers or telecommunication multiplexers installed in close proximity (i.e., less than 2 meters or 6.5ft) to the 6K32.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) to its compact, hot pluggable characteristics, SFPs are becoming a very popular choice for various applications. The small-chassis Magnum 6K is designed for industry-standard Gb-SFPs and Gb-SFPCU (copper) for user selection of the SFP gigabit media type as desired. All SFPs used in Magnum 6Ks are compliant with the industry standard Multi-Source Agreement (MSA) ensuring compatibility with a wide range of networking kit.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) The various SFPs transceivers supported by GarrettCom 6KQs D slot are- Module Model# Gigabit Gb Modules, fixed ports--SFP (Small Form Factor) 6KP2-2GSFP 2 SFP 6KP2-1GSFP1CU 1SFP 1 CU 6KP1-1SFP 1SFP 6KP1-1GCU 1 CU Gb SFP fiber optic transceivers SFP-SX Gb SX, 850nm wavelength, 500 m distance SFP-LX10 Gb LX, 1310nm wavelength, 10km dist SFP-LX25 Gb LX, 1310nm wavelength, 25km distance SFP-ZX40 Gb ZX, 1550nm wavelength
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) and the “Cable Loss” for 100/140 (Multi-mode) is 3.3 dB/km, and the “Cable Loss” for 9/125 (Single-mode) is 0.5 dB/km and the “Cable Loss” for 9/125 (Single-mode) is 0.4 dB/km (LXSC25) and the “Cable Loss” for 9/125 (Single-mode) is 0.25 dB/km(LXSC40) and the “Cable Loss” for 9/125 (Single-mode) is 0.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) • The 100Mb fiber segment must operate in full-duplex (FDX) mode, i.e. the full-duplex (factory default) setting for 100Mbps fiber ports must be used, and • The worst-case OPB of the fiber link must be greater than the fiber cable’s passive Attenuation. (Attenuation = Cable loss + LED aging loss + Insertion loss + safety factor) 3.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) the Magnum 6K32T & 6K32TRC Switches. These brackets are popular in the Telco industry where they are a standard for Central Office rack-mounting purposes. The 23” and the ETSI brackets are mainly used for larger equipment These brackets are rack-mounted in a frame typically accessed in operation from both sides. The bracket mounting holes in the sides of the Magnum 6K32T & 6K32TRC permits it to be mounted in various ways.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) There are three options of brackets available to mount in the standard 19” frame, 23” frame, or ETSI (21”) frame. The 19” brackets are included with each unit, the other two may be purchased as separate options. With each bracket type, there are three different mounting options as shown in Fig. 3.3.2. The case of the Magnum 6K32T has mounting holes prepared for each of the mounting arrangements.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Security violation or an S-Ring Fault, causes the contact to open and thus trigger an alarm in the user’s monitoring system The second (bottom position) NC Alarm Contact is held close when there is power on the main board inside of the 6K32T & 6K32TRC.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Front panel face plate package. The Front panel faceplate package includes 3 retainer brackets and six #2-56 flat head screws. NOTE: Every 6KPM Card package comes with their matching Daughter and Granddaughter board. The copper 6KPM card should not work properly if mixed with other Fiber combo 6KPM card packages. Always install the PM module separately one by one to avoid the mixing.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Fig 3.5.1b: Pulling out the top coved from the chassis base Caution: Be careful not to disturb the power supply. Looking down into the Magnum 6K32T & 6K32TRC unit, notice that there are individual PM installation spaces and female latch (white) connectors provided on the far right side of main board along with four stand-off’s for 6KPM card position. (See Figure 3.5.1c). Figure 3.5.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) the PM Face plate card slot securely. These six screws shown in the picture below are used to secure a PM face plate in position, but unscrew only four of the screws as shown in Fig. below. These screws are also used to secure the individual 6KPM cards screen plate which can be subjected to significant forces from the attached cables. (See Figure 3.5.1d) Figure 3.5.1d: Top View – 6KPM retaining screws hold Face Plate 3.5.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Step 3. The figure here illustrates the basic layout of an individual PM card. 6KPM card fits into the space provided on the main board over the grand-daughter Bd. and the male latched cream color connector( as shown in above fig. with arrow mark). Fig 3.5.2d: Daughter Board shown upside down with two male latch connectors Step 4.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Fig.3.5.2f: Securely latching up 6KPM Cards into a Magnum 6K32T & 6K32TRC & 6K32 NOTE:. When leaving 6KPM slots empty, always use a face plate (Magnum 6K8-BLNK) to cover the slot opening in the front panel. This will maintain proper cooling air flow, safety, and operation as required by FCC, CE, and other regulations. Step 6.
Magnum 6K32T & 6K32TRC Managed Switch Step 8. Installation and User Guide 05/07) Once the 6KPM cards have been installed, the chassis top cover should be replaced by matching at the two front corners properly and slide in until it reaches the rear end and fit properly to match the holes. Make sure the chassis cover is aligned properly before securing the enclosure. Place the front panel part at the end by sliding in to the front side and secure it with 12 screws as being mentioned earlier. 3.5.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) connectors as shown in Fig. 3.5.3b . If the now empty slot is to remain unused, be sure to install a 6KPM-BLNK face plate cover. Figure 3.5.3b: Removing a 6KPM Card Follow the step 8 to complete the process successfully. NOTE:1.
Magnum 6K32T & 6K32TRC Managed Switch 3.6.1 Installation and User Guide 05/07) RS-232 (DB-9) Console Com port (Serial port) pin assignments.
Magnum 6K32T & 6K32TRC Managed Switch 4.0 Installation and User Guide 05/07) OPERATION This chapter describes the functions and operation of the Magnum 6K32T & 6K32TRC Switch. 4.1 Switching Functionality A Magnum 6K32T & 6K32TRC provides switched connectivity at Ethernet wire-speed among all of its ports. The Magnum 6K32T & 6K32TRC support 10/100Mbs for copper media and 10 or 100Mb separate traffic domains for fiber ports to maximize bandwidth utilization and network performance.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) An address-aging algorithm causes least-used addresses to fall out in favor of frequently-used addresses. To reset the address buffer, cycle power down-and-up. 4.2 Status LEDs For all Magnum 6K32T & 6K32TRC models : PWR LK ACT F/H 100/10 4.3 : Power LED, ON when external power is applied to the unit. : Steady ON, Link status for 10 Mbps and 100Mbps operation. : ON with port activity for 10 Mbps and 100Mbps operation.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) remote device. Standard commercially available Fast Ethernet media converters mostly do not support auto-negotiation properly, and require that the switched port to which they are connected be at 100Mb fixed speed. Attachment to 10/100 autonegotiation ports typically will not work properly.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) RJ-45 ports will try to detect its idle signal to determine 10 or 100 speed, and will default to half-duplex at that speed per the IEEE standard. When operating in 100Mb half-duplex mode, cable distances and hop-counts may be limited within that collision domain. The Path Delay Value (PDV) bit-times must account for all devices and cable lengths within that domain.
Magnum 6K32T & 6K32TRC Managed Switch 5.1 Installation and User Guide 05/07) Inspecting the Package and Product This section applies only to PMs shipped as separate items, i.e., 6K32T & 6K32TRC PMs not factory installed in a Magnum 6K32T & 6K32TRC modular slot. Examine the shipping container for obvious damage prior to installing a 6K32T & 6K32TRC PM; notify the carrier of any damage you believe occurred during shipment or delivery.
Magnum 6K32T & 6K32TRC Managed Switch 5.2.1 Installation and User Guide 05/07) 6KP6-RJMST, 4@10/100Mbps RJ-45 and 2@100Mb multi-mode FX-ST “twist 6KP6-RJMST, lock” Combo 4 Port@ 10/100Mbps and 2 @100 Mb ST Fiber Port Module 2 The Magnum 6KP6- 1 RJMST is a combo 6 port module of RJ-45’s at 10/100Mbps and fiber optic ports at 100MB.
Magnum 6K32T & 6K32TRC Managed Switch 5.2.1b Installation and User Guide 05/07) 6KP4-F10ST, 4@10Mb multi-mode FX-ST “twist lock” Module The Magnum 6KP4-F10ST 6KP4-RJ10MST, 4 Port@ 10Mb ST Fiber Port is a 10Mb multi-mode 2 fiber module with 4 STFiber ports. All four fiber ACT F/H ports are ST connectors and configured as 10Mb ACT F/H 1 TX LK RX 3 ACT F/H Half-duplex by default.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) connectors and configured as 10Mb Half-duplex by default for 10Mb fiber and 100Mb Full duplex for the 100Mb fiber. The 10Mb ST-fiber ports allow the user to connect their legacy 10Mb network to the Magnum 6K32T & 6K32TRC switch. They also provide a convenient way for the half duplex hub to connect to the switch through 10Mb fiber ports. Whereas the 100Mb ST module allow to connect the 100Mb demand of Switch devices.
Magnum 6K32T & 6K32TRC Managed Switch 5.2.3 Installation and User Guide 05/07) 6KP6-RJSSC 4@ 10/100Mbps RJ-45 Ports and 2@100Mbps single-mode FX-SC-type, 6KP6-RJMSSC, “snap-in” 4 Port@ 10/100Mbps and 2 @100 Mb SSC Fiber Port connector 2 The Magnum 6KP6-RJSSC 1 is also a Combo module equipped with 4 dual speed copper ports and 2 Singlemode SC-type connectors.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Each port has an Activity (ACT) LED indicating packets being received, a Link (LK) LED indicating proper connectivity with the remote device when lit, and a FDX/HDX LED indicating full-duplex mode when lit (or half-duplex when off). The 10/100 LED indicates the speed for the copper port, which is 100Mbps when the LED is ON and 10 Mb when the LED is OFF. 5.2.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) connectivity. When installed in a Magnum 6K32T & 6K32TRC Switch, it supports fiber optic cable distances up the IEEE-standard 100Mbps distance limits, i.e., typically 2km at full-duplex and 412m at half-duplex. The functionality of this 100BASE-FX multi-mode 8 Port module is essentially the same as the ST and SC-types. It has the same LEDs per port indicating port activity (ACT), Link (LK), and FDX or HDX operation. 5.2.
Magnum 6K32T & 6K32TRC Managed Switch 5.2.6 Installation and User Guide 05/07) 6KP8-45MT, 4@ 10/100Mbps RJ-45 and 4@100Mb multi-mode FX , MTRJ Small-Form-Factor The Magnum 6KP8-45MT 6KP8-45MT Module is a combo module with 4 Port@ 10/100Mbps & 4 port @ 100Mbps Multi-Mode Fiber port 2 copper and fiber (Small Form Factor) MTRJ type ports. The small size of 1 MTRJ connectors give an advantage of placing more ports on one module.
Magnum 6K32T & 6K32TRC Managed Switch 5.2.8 Installation and User Guide 05/07) 6KP8-45LC, Combo 4@ 100Mbps multi-mode -LC small-form factor and 4@ 10/100 Mbps RJ-45 Connector The Magnum 6KP8- 45LC Module is a combo module 4 Port@ 10/100Mbps & 4 port @ 100Mbps Multi-Mod LC Fiber port with a combination of copper and 2 Fiber (Small Form Factor) LC 1 type ports. The small size of LC 3 1 5 LK 10/10 connectors allows an advantage of 4 ACT F/ having more ports on one module.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) ports for cascaded connection. This feature eliminates the need for a special twisted pair crossover cable when connecting to a hub or another switch.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) The LEDs on 6KP8-RJ45- PoE modules are slightly different compared to regular (non-PoE) RJ-45 modules as shown in Fig 2. When the PoE port is in use, the PoE LED is ON when connected properly to an 803.af compliant PD device on that port. When non-PoE devices are connected, the PoE LED is OFF. PoE does not affect operation of Ethernet data traffic.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Inside) option in one 6K-unit. In this Fig. the top 4-RJ45 ports are enhanced with POE option whereas as bottom 4- RJ-45 are normal MDIX ports. The 4-RJ45 POE module are also available with mix –n-match with fiber modules. Please check the ordering information Sec.1.2. for all the various PI6K PoE modules option. The LEDs on 6KP8-RJ45- PoE module are slightly different compared to regular (non-PoE) RJ-45 modules as shown in Fig 2.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) 5.2.11 6KP8-45-2MT, 6@ 10/100Mbps RJ-45 and 2@100Mb multi-mode FX , MTRJ Small-Form-Factor The Magnum 6KP8-45-2MT eight port Module is a combo module with copper and fiber (Small Form Factor) MTRJ type ports. The small sizes of MTRJ connectors give an advantage of placing more fiber ports on one module. The 6KP8-45-2MT is equipped with six 10/100 RJ-45 ports and two 100Mb MTRJ fiber ports.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) The GBIC transceiver has been offered in the modular slot with multiple options as per the user requirement. The two Giga port has been offered as GBPM-2OTX (fiber or RJ45), whereas the single Gigabit module comes in flavor of G+2 (100Mb fiber ports) or G+4(10/100 RJ-45 ports) as shown in the above figure. The GBIC transceiver is fastened using snap-in clips.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Each port has an Full and Half Duplex (F/H) Activity, (ACT) LED indicating packets being received and a Link (LK) LED indicating proper connectivity with the remote device when lit 5.2.12b GBIC-LXSC Gigabit fiber (1000Mb), multi-mode SC Connector The Magnum GBIC-LXSC is a single-mode Gigabit fiber connector equipped with SC type connectors and can be easily snapped in and out.
Magnum 6K32T & 6K32TRC Managed Switch 6.0 Installation and User Guide 05/07) TROUBLESHOOTING All Magnum Ethernet products are designed to provide reliability and consistently high performance in all network environments. The installation of a Magnum 6K32T & 6K32TRC Switch is a straightforward procedure (see INSTALLATION, Section 3.0); the operation is also straightforward and is discussed in Section 4.
Magnum 6K32T & 6K32TRC Managed Switch 5. Installation and User Guide 05/07) If the problem continues after completing Step 4 above, contact your supplier of the Magnum 6K32T & 6K32TRC Switch unit or if unknown, contact GarrettCom, Inc.by fax, phone or email (support@garrettcom.com) for assistance. 6.2 When Calling for Assistance Please be prepared to provide the following information. 1. A complete description of the problem, including the following points: a.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) Product name Serial Number (or Invoice Number) Packing List Number (or Sales Order Number) Date of installation Failure symptoms, including a full description of the problem.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) During this warranty period, GarrettCom will repair or, at its option, replace components in the products that prove to be defective at no charge other than shipping and handling, provided that the product is returned pre-paid to GarrettCom. This warranty will not be effective if, in the opinion of GarrettCom, the product has been damaged by misuse, misapplication, or as a result of service or modification other than by GarrettCom.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) correctly applied to the two inputs. It protects the Switch from incorrect DC input connections. An incorrect polarity connection, for example, will neither affect the Switch, its internal power supply, nor will it blow the fuse in the internal power supply. The manual power “On-Off” Switch (optional) is used for powering the unit on and off when it is placed into or taken out of service. B3.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) The actual connection procedure is very straightforward. Simply connect the leads to the Magnum unit, beginning with ground. Ensure that each lead is securely tightened. Note: The GND should be hooked up first. The 6K32T & 6K32TRC unit has a floating ground, so the user may elect to Ground either + or - terminal to suit the customer’s use.
Magnum 6K32T & 6K32TRC Managed Switch B7.0 Installation and User Guide 05/07) TROUBLESHOOTING Please refer to Section 6.0 for troubleshooting APPENDIX C: Internal DC Dual-Source Power Option C1.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) C3.0 DUAL-SOURCE OPTION, THEORY OF OPERATION The Dual-Source DC power option is designed using diodes inside of the chassis on each DC power input line. A diode is placed in each of the four input lines (behind the four external power connection terminals) so that power from an external source can only flow into the unit. This allows the unit to operate whenever DC power is correctly applied to either or both of the two inputs C4.
Magnum 6K32T & 6K32TRC Managed Switch Installation and User Guide 05/07) lead from 48V or –48V supply must be connected to the post labeled “+”. The connection procedure is straightforward. Simply connect the DC leads to the Switch’s power terminals, positive (+) and negative (-) screws. Ensure that each lead is securely tightened. The 24VDC and 125VDC terminal block on Magnum 6K32T & 6K32TRC’s is similar to that described in the –48VDC information above. C5.
