Corporate Headquarters GarrettCom, Inc. 47823 Westinghouse Dr. Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com Magnum 6K32T email support@garrettcom.com Managed Switch Installation and User Guide Hardware User Manual www . GarrettCom . com www . GarrettCom .
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Magnum™ 6K32T Managed Switch Hardware Installation and User Guide Part #: 84-00138 (Rev. B) Trademarks Ethernet is a trademark of Xerox Corporation NEBS is a trademark of Telcordia Technologies UL is a registered trademark of Underwriters Laboratories GarrettCom, Magnum, Personal Switch, S-Ring, Link-Loss-Learn, Converter Switch and Convenient Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Contacting GarrettCom, Inc Please use the mailing address, phone and fax numbers and email address listed GarrettCom, Inc. below: 47823Westinghouse Dr. Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com email support@garrettcom.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) TABLE OF CONTENTS.......................................................................... Page SPECIFICATIONS ................................................................................ 1 1.0 1.1 Technical Specifications....................................................................... 1 1.2 Ordering Information ........................................................................... 4 2.0 INTRODUCTION.................
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 4.5 Flow-control, IEEE 802.3x standard.................................................. 41 4.6 Power Budget Calculations for Magnum 6K32T PM’sError! Bookmark n 5.0 MAGNUM 6K32T MANAGED SWITCH PORT MODULES ....... 41 5.1 Inspecting the Package and Product................................................... 41 5.2 6KPM Module Description ................................................................ 42 5.2.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) The Magnum Line ETHERNET CONNECTIVITY PRODUCTS "DESIGNED AND MANUFACTURED IN THE USA" OVERVIEW GarrettCom, Inc. offers the premium-quality Magnum™ line of Ethernet LAN connectivity products with industry-standard functionality and built-in fiber configurability. Magnum products are designed for use in demanding Carrier Class, Industrial Grade and OEM applications where reliability is a primary consideration.
Magnum 6K32 & 6K32T Managed Switch 1.0 1.1 Installation and User Guide (12/05) SPECIFICATIONS Technical Specifications Performance Filtering / Forwarding Rate: Ethernet:14,880 pps Fast Ethernet: 148,800 pps Gigabit Ethernet: 1,488,000 pps Switching Processing Type: Store and Forward with IEEE 802.
Magnum 6K32 & 6K32T Managed Switch Fiber connector types supported: ST-type (twist-lock) SC-type (snap-in) MTRJ-type Small Form Factor (SFF) LC-type Installation and User Guide (12/05) Small Form Factor (SFF) GBIC modules LEDs: Per Port LK: Steady ON when media link is operational ACT: ON with receiver port activity FDX/HDX: ON = Full-Duplex Mode OFF = Half-Duplex Mode 100/10: ON = 100Mbps speed OFF = 10 Mbps Operating Environment UL 60950 “Component Parts” temp.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) For (Optional) DC internal power supplies at –48VDC, 24VDC and 125VDC, including Dual Source options (for continuity of operation when either of the DC input sources are interrupted), see Appendices B and C. Relay Alarm Contact (Optional) The Alarm Contact option is offered as a configuration option.
Magnum 6K32 & 6K32T Managed Switch 1.2 Installation and User Guide (12/05) Ordering Information Magnum Managed Switch MODEL DESCRIPTION Magnum 6K32T 24 10/100 RJ-45 ports and either two optional port modules (6K32T) or one optional port module slot (6K32), which may be configured with a selection of 10/100/1000Mb fiber and copper connector types, 8 ports max.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) GBIC-SXSC GBIC transceiver module for use in GBPM-xOTX.
Magnum 6K32 & 6K32T Managed Switch 2.0 2.1 Installation and User Guide (12/05) Introduction Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product; notify the carrier of any damage that you believe occurred during shipment or delivery. Inspect the contents of this package for any signs of damage and ensure that the items listed below are included.
Magnum 6K32 & 6K32T Managed Switch 2.2 Installation and User Guide (12/05) Product Description - Magnum 6K32T Managed Switch The Magnum 6K32T Managed Switch provides high port density, with up to 32 ports in a 1U rack-mount package. It is used to boost the performance of large Ethernet LANs, typically serving as a “backbone” switch in carrier-class (Telco) or Industrial applications of various media requirements of copper and Fiber.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) accommodated include standard 19” RETMA, ETSI, and 23” Telco. Input power may be AC, or –48VDC for Telco environments, or 24VDC for Industrial applications. Designed for use in network traffic centers, the Magnum 6K32T provides high performance plug-and-play hardware operation, 802.1p packet prioritization in hardware, and industry-standard managed networks software functionality, all in convenient 1U rack-mount packages. 2.2.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Magnum 6K32T is easy to deploy, manage and maintain. Addresses of attached nodes are automatically learned and maintained, adapting the switching services to network changes and expansions to provide pug-n-play operation. 2.2.1b New Magnum 6K32T Chassis The New 6K32T Switches have 16port fixed 10/100Mb RJ-45 ports and 2 modular slots available to configure with numerous options.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 2.2.2 Eight-port SFF fiber modules (6K8-MTRJ, 6K8-MLC), 100Mb fiber 1 3 5 7 ACT ACT F/H ACT F/H ACT F/H F/H LK LK LK LK ACT ACT F/H F/H ACT ACT F/H LK 2 4 LK LK 6 8 Fig.2.2.2 : SFF Fiber Port Modules, 6K8-MTRJ (to the left) and 6K8-MLC or -SLC (below) F/H LK In an eight-port SFF fiber port module, all of the fiber ports are of the same speed (100Mb), mode, and connector type.
Magnum 6K32 & 6K32T Managed Switch 2.3 Installation and User Guide (12/05) Eight-Port Copper 1 3 5 7 LK 10/100 Module, 6K8-RJ45 The 6K-Series’s 8-port Copper F/ H port module, model 6K8-RJ45, 2 4 6 8 ACT 10/100 LK F/H ACT provides eight 10/100Mb switched RJ-45 ports. The 10/100Mb switched ports normally (as a default setting) are independently N-way auto-negotiating, and auto-crossover(MDIX) for operation at 10 or 100Mb speed in full- or half-duplex mode, i.e.
Magnum 6K32 & 6K32T Managed Switch 2.2.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) The 4port @10Mb ST fiber modules behave the same as the 8@100Mb ST fiber modules except for the 10Mb speed. For port numbering, ports 1, 2, 5, 6 are present, ports 3, 4. 7, 8 are not present. The default setup on the 10Mb fiber module is halfduplex, which allows the Magnum 6K32T Switch to connect to any 10Mb hub or media converter or almost any other device with a 10Mb fiber Ethernet port.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) port is by default configured to AUTO mode, and can be fixed at 1000Mbps speed fullduplex mode at any time. The Gigabit fiber port has LEDs that indicate LK (Link status) and ACT (receiving activity) on that port when lit. 2.2.7 Packet Prioritization, 802.1p QOS Quality of Service means providing consistent predictable data delivery to users from datagram paths that go all across a network.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) devices sending packets to cause “flow control”. This tells the sending devices to temporarily stop sending traffic, which allows a traffic catch-up to occur without dropping packets. Then, normal packet buffering and processing resumes. Another feature implemented in Magnum 6K32T Switches is a collision-based flow-control mechanism (when operating half-duplex only).
Magnum 6K32 & 6K32T Managed Switch 2.3 Installation and User Guide (12/05) Features and Benefits Managed switching for high performance Ethernet LANs Magnum 6K32T Switches provide non-blocking (all ports can run at full speed at once) performance with standard Managed Networks Software (MNS-6K) included. They are typically used in LAN traffic centers with 24 10/100Mb ports or one or two Gigabit ports for backbone connections where managed network services are desired.
Magnum 6K32 & 6K32T Managed Switch 2.4 Installation and User Guide (12/05) Applications Magnum 6K32T Fiber Switches offer high performance along with one or two modular slot options to fulfill the choice of copper/Fiber, 10,100 or 1000Mb requirements. The 6K32T also offers MNS-6K management software.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) fire hazards can be connected to one or two full duplex Gigabit Fiber ports. Full-duplex future proof fiber media can easily connect long distance subnets and provide a stable secure network to all applications. The SNMP management capability of the Magnum 6K32T Switch helps create a database of all the network subnets to easily manage the network.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) support of 10/100 and 1000Mb. The user can utilize the SNMP feature equipped with VLAN, Port security, 802.1X, and other security features to provide a secure and stable network as per the requirement The 6K32T Managed Switch with NEBS Level 3 compliance and management flexibility allows the user more than one configuration alternative.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Example 4: In a “ (video+data)” application where a network being designed to catered the need of multicast and broadcast traffic of higher bandwidth to provide a video conferencing and video in demand channel option to the user. The Magnum 6K32T with two slots to filled with Gigaport module and a robust management firmware with MNS-6K qualify this requirement efficiently.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Figure 4: A multicast traffic through a 6K32T Switches with Gigabit redundancy www . GarrettCom .
Magnum 6K32 & 6K32T Managed Switch 3.0 Installation and User Guide (12/05) Installation Before installing the equipment, it is necessary to take the following precautions: 1.) If the equipment is mounted in an enclosed or multiple rack assembly, the environmental temperature around the equipment must be less than or equal to 500C. 2.) If the equipment is mounted in an enclosed or multiple rack assembly, adequate airflow must be maintained for proper and safe operation. 3.
Magnum 6K32 & 6K32T Managed Switch 3.2 Installation and User Guide (12/05) Connecting Ethernet Media The Magnum 6K32T Switches are specifically designed to support all standard Ethernet media types within a single Switch unit. This is accomplished by using a family of different port Modules which can be individually selected and configured per-port. See Section 2.4 for a description of the PMs. The various media types supported along with the corresponding IEEE 802.3 and 802.
Magnum 6K32 & 6K32T Managed Switch 3.2.2 Installation and User Guide (12/05) Connecting Fiber Optic SC-type, "Snap-In" The following procedure applies to installations using a PM with SC-type fiber connectors, i.e., using 6K-MSC or 6K-SSC (single mode) etc. When connecting fiber media to SC connectors, simply snap the two square male connectors into the SC female jacks of the 6KPM until they click and are secure. 3.2.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 3.2.5 Connecting Twisted Pair (CAT-5e or better, Unshielded or Shielded) The RJ-45 1000BASE-TX Gigabit ports of the Magnum 6K32T can be connected via copper media with the following minimum specifications; 1000BASE-T, CAT-5e, or for better results, 100-ohm UTP shielded twisted pair (STP) balanced cable.
Magnum 6K32 & 6K32T Managed Switch Fiber Port Module Speed, 6KP4F10ST 10Mb MultiMode FL Std. Installation and User Guide (12/05) Std. Wave Cable X’mitr R’cvr Worst Worst* typical typical* Size Output Sens. OPB, distance OPB, distance Mode km fdx length µm dB Km, fdx PT , dB PR ,dB dB Km, fdx (hdx) nm 850 62.5/125 -15.0 100/140 -9.5 50/125 -19.5 -31 -31 -31 14 19.5 19.5 5 5.9 3.4 17 23.5 13.5 6 7 4.8 100Mb Multi2 1300 62.5/125 -20 FX mode (0.4) 50/125 -23.
Magnum 6K32 & 6K32T Managed Switch 3.3 Installation and User Guide (12/05) Table-Top or Shelf Mounting The Magnum 6K32T Managed Switches can be easily mounted on a table-top or any suitable horizontal surface. They have four rubber feet to provide stability without scratching finished surfaces. 3.3.1 Rack-mounting (for 19” RETMA racks), Magnum 6K32T’s Installation of a Magnum 6K32T Fiber Switch in a 19” rack is a simple procedure. The units are 1U (1.70”) high.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Fig 3.3.1 Dual Side-Mountings for Magnum 6K32T units These brackets are rack-mounted in a frame typically accessed in operation from both sides. The bracket mounting holes in the sides of the Magnum 6K32T permits it to be mounted in various ways. The same holes fit all three types (19”, ETSI, and 23”) of brackets. The mounting for the 23” is illustrated in Figure 3.3.1 below.
Magnum 6K32 & 6K32T Managed Switch 3.4 Installation and User Guide (12/05) Powering the Magnum 6K32T Managed Switch The Magnum 6K32T Switches incorporate an internal universal power supply and have a recessed male IEC connector for the AC power cord at the left-rear. A manual power ON-OFF switch is adjacent. A six-foot 115 VAC 60 Hz standard power cord is supplied with each unit shipped within the United States and Canada.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 4. By default it is NC (normally closed) 5. The software operation needs to be enabled and set to get the Alarm traps. For detailed information about the Software Alarm and software control of SNMP alarm traps, please reference the Magnum MNS-6K Software User Manual. (Chapter 19th). 3.
Magnum 6K32 & 6K32T Managed Switch Step 2. Installation and User Guide (12/05) Remove Chassis Cover The Magnum 6K32T chassis are combined with top, bottom and front panel parts and assembled together with the help of 17 Philips-head screws. There are 5 screws located on the front-bottom and 3 at rear-top of the unit and one each on the front and rear sides. First Remove the front panel screws (total 12) as shown in the fig 3.5.1a.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Looking down into the Magnum 6K32T unit, notice that there are individual PM installation spaces and female latch (white) connectors provided on the far right side of main board along with four stand-off’s for 6KPM card position. (See Figure 3.5.1c). Figure 3.5.1c: Magnum 6K32T modular slot side (front-right side), without chassis cover Step 3.
Magnum 6K32 & 6K32T Managed Switch Step 2. Installation and User Guide (12/05) Placed Granddaughter board (as shown in fig. 3.5.2a and 3.5.2b) on the chassis built in stand off (female) provided at the front of the 6K32T Main Board and screw down tightly with the three 5/16 stand-off (male) on the top of the Granddaughter board The 5/16 stand off has been used to place the daughter board on the top of the granddaughter board and latch it securely. Fig 3.5.
Magnum 6K32 & 6K32T Managed Switch Step 4. Installation and User Guide (12/05) Hold the daughter board with both hands at the end and align the two cream color latching connectors (male) placed at the bottom of the daughter board with the other female connector placed on the Granddaughter and main board. As shown above in Fig. 3.5.2e Step 5.
Magnum 6K32 & 6K32T Managed Switch Step 8. Installation and User Guide (12/05) Once the 6KPM cards have been installed, the chassis top cover should be replaced by matching at the two front corners properly and slide in until it reaches the rear end and fit properly to match the holes. Make sure the chassis cover is aligned properly before securing the enclosure. Place the front panel part at the end by sliding in to the front side and secure it with 12 screws as being mentioned earlier. 3.5.
Magnum 6K32 & 6K32T Managed Switch Step 3. Installation and User Guide (12/05) Remove 6KPM Card Carefully and gently pull out the daughter board from the latching connectors, using both hands, gripping the board near the latch-up connectors as shown in Fig. 3.5.3b . If the now empty slot is to remain unused, be sure to install a 6KPM-BLNK face plate cover. Figure 3.5.3b: Removing a 6KPM Card Follow the step 8 to complete the process successfully. NOTE:1.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Note: For detail description of Managed Network Software (MNS-6K) and Magnum 6K32T Switch configuration for Network Management, please refer to Magnum 6K32T Software Manual available on GarrettCom‘s FTP site. Detail info. about the MNS is available on 2.2.9 ( see page no. 13) of this manual. 3.6.1 RS-232 (DB-9) Console Com port (Serial port) pin assignments.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 6K32T, but local traffic on a port will not consume any of the bandwidth on any other port. Magnum 6K32T units are plug-and-play devices. There is no software configuring necessary to be done for basic operation at installation or for maintenance. The only hardware configuration settings are user options for an UP-LINK Switch (resides inside the unit) on the 6K8-RJ45 (modular port).
Magnum 6K32 & 6K32T Managed Switch 4.3 Installation and User Guide (12/05) Up-link Cross-over Switch on RJ-45 port modules, for port#1 only The modular slot provided on Magnum 6K32T managed switch can be filled with 6KP8-RJ45 port module among all the multiple choices of port modules. The upper part of the copper port module (6KP8-RJ45) has a manual Up-link switch, located on the inside of the unit on the port module board next to the RJ45 port # 1 which it controls.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) negotiation ports typically will not work properly. The 6K32T Switch’s RJ-45 ports handle this situation by configuring the ports as per desire through MNS software port settings and can check the port status of each port after the change.
Magnum 6K32 & 6K32T Managed Switch 4.5 Installation and User Guide (12/05) Flow-control, IEEE 802.3x standard Magnum 6K32T Switches incorporate a flow-control mechanism for Full- Duplex mode. The purpose of flow-control is to reduce the risk of data loss if a long burst of activity causes the switch to save frames until its buffer memory is full. This is most likely to occur when data is moving from a 100Mb port to a 10 Mb port and the 10Mb port is unable to keep up.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) at a later date. In the event there are items missing or damaged, contact your supplier. If you need to return the unit, use the original shipping container if possible. Refer to Chapter 5 for specific return procedures. 5.2 6KPM Module Description An important feature of the Magnum 6K32T is the use of one Port Modules for flexible mixed-media connectivity to RJ-45 and fiber media in the modular slot.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Each port has an Activity (ACT) LED indicating packets being received, a Link (LK) LED that indicates proper connectivity with the remote device when lit, and FDX/HDX LED to indicate full-duplex mode when lit (or half-duplex when off). The 10/100 LED indicates the speed, if the LED is ON 100Mbps if it is OFF 10Mbps. 5.2.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Each port has an Activity (ACT) LED indicating packets being received, a Link (LK) LED indicating proper connectivity with the remote device when lit, and FDX/HDX LED indicating full-duplex mode when lit (or half-duplex if off). 5.2.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 5.2.2. 6KP6-RJMSC 4@10/100Mbps RJ-45 and 2@100Mb multi-mode FX-SC “snap-in” Fiber connector 6KP6-RJMSC, The Magnum 6KP6- 4 Port@ 10/100Mbps and 2 @100 Mb SC Fiber Port 2 RJMSC is also a Combo 6 Port module equipped with 4 10/100Mb 1 3 5 1 7 LK 10/100 RJ-45 ports along with 2 multimode 100Mbps fiber optic ACT F/H F/H 2 transceivers all in one module. This 1 is similar to the 6K6-RJMST.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 10/100 LED indicates 100Mbps speed when lit and 10Mbps speed when off. To distinguish the single-mode 6 K6-RJSSC from the multi-mode 6K6-RJMSC, the label “Sgl. M.” is at the top of the faceplate of the 6K6-RJSSC. 5.2.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 5.2.5 6KP8-MTRJ, 8 @100Mb multi-mode FX , MTRJ Small-Form-factor Magnum 6KP8-MTRJ is a multi-mode fiber optic 8-port module equipped with a small-form-factor MTRJ-type 6KP8-MTRJ,“small-form-factor” connector. It looks almost like 8 Port@ 100Mbps Multi-Mode Fiber port an RJ-45 port, but it is black in 1 color.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) indicating port activity (ACT), Link (LK), and FDX or HDX operation 5.2.6 6KP8-45MT, 4@ 10/100Mbps RJ-45 and 4@100Mb multi-mode FX , MTRJ Small-Form-Factor The Magnum 6KP8-45MT 6KP8-45MT Module is a combo module with 4 Port@ 10/100Mbps & 4 port @ 100Mbps Multi-Mode Fiber port 2 copper and fiber (Small Form Factor) MTRJ type ports. The small size of 1 MTRJ connectors give an advantage of placing more ports on one module.
Magnum 6K32 & 6K32T Managed Switch 5.2.8 Installation and User Guide (12/05) 6KP8-45LC, Combo 4@ 100Mbps multi-mode -LC small-form factor and 4@ 10/100 Mbps RJ-45 Connector The Magnum 6KP8- 45LC Module is a combo module 4 Port@ 10/100Mbps & 4 port @ 100Mbps Multi-Mod LC Fiber port with a combination of copper and 2 Fiber (Small Form Factor) LC 1 type ports. The small size of LC 3 1 5 LK 10/10 connectors allows an advantage of 4 ACT F/ having more ports on one module.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Link (LK) LED that indicates proper connectivity with the remote device when lit, a FDX/HDX LED to indicate full-duplex mode when lit (or half-duplex when off), and a “10/100” LED indicating 100Mb when lit (or 10 Mbps when off).
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) 2SLC is equipped with 6 10/100 RJ-45 ports and 2 Single-mode fiber ports. When installed in a Magnum 6K32T Switch, it supports the standard distances as mentioned on 5.2.4. and the LEDs also act similarly. 5.2.11 GBIC-SXSC Gigabit fiber(1000Mb), multi-mode SC Connector The Magnum GBIC-SXSC is a multi-mode Gigabit fiber connector equipped with SC type connectors and can be easily snapped in and out.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) ACT F/ TX LK RX ACT ACT F/ F/ TX L TX RX LK RX 1@ 1000Mb Fiber SC + 2@ 100Mb SC The two Giga port has been offered as GBPM-2OTX (fiber or RJ-45), whereas the single Gigabit module comes in flavor of G+4(10/100 RJ-45 ports) or G+2 (100Mb fiber ports) as shown below in the above figure.
Magnum 6K32 & 6K32T Managed Switch 5.2.12 Installation and User Guide (12/05) 6KM-BLNK The 6K8-BLNK is a blank face plate or cover plate that must be installed in any empty 6K32T PM slot to maintain proper cooling air flow, safety, etc. Two screws underneath the front panel hold the 6KM-BLNK in place. 6.0 TROUBLESHOOTING All Magnum Ethernet products are designed to provide reliability and consistently high performance in all network environments.
Magnum 6K32 & 6K32T Managed Switch 5. Installation and User Guide (12/05) Always check your Switch configuration, specially Auto-negotiation behavior with other connected device to have proper setup tested. 5. If the problem continues after completing Step 4 above, contact your supplier of the Magnum 6K32T Switch unit or if unknown, contact GarrettCom, Inc.by fax, phone or email (support@garrettcom.com) for assistance. 6.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) Product name Serial Number (or Invoice Number) Packing List Number (or Sales Order Number) Date of installation Failure symptoms, including a full description of the problem.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) than shipping and handling, provided that the product is returned pre-paid to GarrettCom. This warranty will not be effective if, in the opinion of GarrettCom, the product has been damaged by misuse, misapplication, or as a result of service or modification other than by GarrettCom. GarrettCom reserves the right to make a charge for handling and inspecting any product returned for warranty repair which turns out not to be faulty.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) The manual power “On-Off” Switch (optional) is used for powering the unit on and off when it is placed into or taken out of service. B3.0 APPLICATIONS FOR DC POWERED SWITCHES Magnum 6K32T Fiber Switches are easily installed in a variety of applications where -48VDC, 24VDC and 125VDC power is used as the primary power source.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) lead from 48V or –48V supply must be connected to the post labeled “+”. An ON-OFF manual switch is optional for DC power. This can be used to cut off power connections and as a RESET for the Magnum 6K32T Switch. B4.1 1. 2. 3. 4. 5. 6. B5.0 UL Requirements for DC-powered units Minimum 18AWG cable for connection to a Centralized DC power source. Minimum 14AWG cable for connection to a earthing wiring.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) GND: Terminal for “earth” or ground wire connection to the hub chassis Input: Two separate sources, each at 20 - 36 VDC Power Supply (Internal, 125VDC Dual-Source, model # Dual-Src-24V) DC Power Connector: First Source: “A+”, “A-“, 2nd Source “B-“, “B+” GND: Terminal for “earth” or ground wire connection to the hub chassis Input: Two separate sources, each at 88 - 150 VDC With the exception of the dual DC input power connections and the
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) reversed while the Switch is operating from the other source. e) The Switch will not receive power (and will not work) when both inputs are simultaneously absent or are both incorrectly connected. C5.
Magnum 6K32 & 6K32T Managed Switch Installation and User Guide (12/05) C5.1 UL Requirements The following must be adhered to in order to conform to UL requirements: 1. Minimum 18 AWG cable for connection to a Centralized DC power source. 2. Minimum 14 AWG cable for connection to earthing wiring. 3. Use only with Listed 10 A circuit breaker provided in building installation. 4. “Complies with FDA radiation performance standards, 21 CFR subchapter J.” or equivalent. 5.
