Corporate Headquarters GarrettCom, Inc. 47823 Westinghouse Dr. Fremont, CA 94539 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com Magnum S14 Convenient Switch & PS14P Power Source Switch (PoE) (Members of the Converter Switches family) email support@garrettcom.com Installation and User Guide www . GarrettCom . com www . GarrettCom .
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Magnum™ S14 & PS14P (PoE) Convenient Switches Installation and User Guide Part #: 84-00100 Rev. B (01/06) Trademarks GarrettCom, Magnum, Link-Loss-Learn, S-Ring, Convenient Switch and Converter Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Federal Communications Commission Radio Frequency Interference Statement This equipment generates, uses and can radiate frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer's instructions, may cause interference to radio communication.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Contacting GarrettCom, Inc Please use the mailing address, phone and fax numbers and email address listed below: GarrettCom, Inc. 47823 Westinghouse Dr. Fremont, CA 94539 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com Email: support@garrettcom.com www . GarrettCom .
S14 & PS14P (PoE) Convenient Switches TABLE OF CONTENTS Installation and User Guide (01/06) Page 1.0 SPECIFICATIONS ............................................................................... 1 1.1 Technical Specifications ..................................................................... 1 2.0 INTRODUCTION ............................................................................... 11 2.1 Inspecting the Package and the Product............................................. 12 2.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 3.7 S14H & S14P, DC-powered, Installation ......................................... 52 3.7.1 Power Requirement for PS14P(PoE) Power Source Switch.......... 54 3.8 Connecting Twisted Pair (RJ-45 ports).............................................. 55 3.8.1 Connecting Twisted Pair ( Unshielded or Shielded)................. 56 3.8.2 Connections to NICs which support Auto-Neg RJ-45 ports...... 57 4.0 OPERATION ............................
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 10/04: Small edit and updates on power supply option. 09/04: Small edit and updates on UL. 06/04: Small revision of the Agency Approvals Rev A 03/04: Initial release of this user manual for the S14 Converter Switch GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or model offerings without notice. www . GarrettCom .
S14 & PS14P (PoE) Convenient Switches 1.0 SPECIFICATIONS 1.1 Technical Specifications Installation and User Guide (01/06) Ports Performance When a port is operating at 100Mbps: Data Rate: 100Mbps When a port is operating at 10 Mbps: Data Rate: 10 Mbps Network Standards 100Mb: Ethernet IEEE 802.3u, 100BASE-TX, IEEE 802.1p 10 Mb: Ethernet IEEE 802.3, 10BASE-T Power Over Ethernet: IEEE 802.3af (PS14P model only) Auto-sensing for speed: IEEE 802.3u Data packets that have the 4-bytes tagged VLAN field (802.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Packet-Processing Between Domains Filter / Forwarding Rate from 100Mbps ports: 148,800 pps max Filtering and Forwarding Rate from 10 Mbps ports: 14,880 pps max. Processing type: Store and Forward, non-blocking Auto-learning: 2K address table Address buffer age-out time: 300 sec.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Operating Environment Ambient Temperature (S14): 32ºF to 104ºF (0ºC to 40ºC) (S14H): -13ºF to 140ºF (-25ºC to 60ºC) Long term per independent agency tests (UL) -40ºF to 167ºF (-40ºC to 75ºC) Short term per IEC Type tests (S14P & PS14P): -40ºF to 185ºF (-40ºC to 85ºC) Long term per independent agency tests (UL) -40ºF to 167ºF (-40ºC to 75ºC) Short term per IEC Type tests Storage Temperature, All models: -40ºF to 185ºF (-40ºC to 85ºC)
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Note: H and P models are designed for NEBS compliance, including, vibration, shock and altitude. Packaging: Enclosure: Robust sheet metal (Steel). Dimensions, Switch unit: Height x Width x Depth S14, S14H, S14P & PS14P: 3.5 in H x 3.0 in W x 1.0 in D (8.9 cm x 7.6 cm x 2.5 cm) Weight: all S14 models: 4.6 oz. (130g); power supply, –d, and i: 5.9 oz (170g) –Hd, and Hi: 5.8 oz (165g) –Pd, and =Pi: 7.9 oz (225g) PS14P units: 9.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) POWER SUPPLY (S14 Model only) These products are intended to be supplied by a Listed, Direct Plug-In power unit, marked “Class 2”, or a Listed ITE Power Supply, marked “LPS”, which has suitably rated output voltage (i.e. 9vdc, 12vdc, 24vdc, 48vdc), and suitably rated output current (i.e. 100mA to 500mA).When connected to a 48 V centralized dc source these products shall be provided with a Listed 5 A DC fuse in the supply circuit.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) DC to unit: 12V DC, 2.5mm jack, center +ve, 6ft. cord Power Supply ( Direct DC ): built-in screw terminal block for +, -, ground. The 12V DC jack is also present. 12V DC internal (range of 8.0 to 15V DC), 24V DC internal (range of 18 to 36V DC) -48V DC internal (range of 36 to 60V DC) t. Power Consumption: 3 watts typical, 4 watts max.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Terminal block for -48v DC input (range of 46 to 60V dc), built in for +, - , ground. The 815V DC jack is also present, but it can only be used to power the PS14P unit itself, not PoE devices attached. POWER OUTPUT: (PS14P(POE) unit only) PoE available on all four RJ-45 ports via Ethernet twisted pair cabling on port pins using spare pairs 4,5(+) 7,8(-), not the data pair 1,2(-), 3,6(+) 802,3af Power Consumption: 61.6 watts max.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) LED Indicators (Dual- front and end, port #4 has front only) POWER: Steady ON when power applied (S14 model) ON for -48V power applied to the PS14P unit PoE, ports 1,2,3,4: ON when delivering power (PS14P) 10/100: = 100Mbps; OFF = 10 Mbps LK/ACT: Steady ON for LINK with no traffic, blinking indicates port is transmitting / receiving.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Agency Approvals and Standard Compliance: UL Listed (UL 60950), cUL, CE, Emissions meet FCC Part 15, Class A. NEBS L3 and ETSI compliant H & P models: IEEE P1613 Env.
S14 & PS14P (PoE) Convenient Switches 1.2 Installation and User Guide (01/06) Summary of models and descriptions: S14-d,i = four 10/100 RJ-45 ports Switch, for office and wiring closet env., ext. AC Pwr Supply S14H-Hd, Hi = Hardened, four 10/100 RJ-45 ports Switch, Factory floor, Int. 8-15VDC, Ext. AC Hardened power supply included . S14H-12VDC = Same as S14H model, except Ext.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Magnum PS14P (PoE) Power Source Switch (model and descriptions) PS14P = ,Premium rated, four 10/100 RJ-45 ports Switch in a compact package, rated for uncontrolled(outdoor) env. All four RJ-45 Ethernet ports support Power Source PoE as per the IEEE 802.3ad standard. Includes integral -48V DC terminal block for power unit.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 2.1 Inspecting the Package and the Product Examine the shipping container for obvious damage prior to installing this product; notify the carrier immediately of any damage which you believe occurred during shipment or delivery. Inspect the contents of this package for any signs of damage and ensure that the items listed below are included.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Remove the Magnum S14-Series Switch from the shipping container. Be sure to keep the shipping container should you need to ship the unit at a later date. In the event there are items missing or damaged contact your supplier. If you need to return the unit use the original shipping container. Refer to Section 5 Troubleshooting, for specific return procedures. 2.
F/H PWR 3 LA3 10/100 LA1 PORT 4 1 Magnum S14 Convenient Switch LA2 GarrettCom PORT 2 LK/ACT 10/100 2 PORT 3 Installation and User Guide (01/06) PORT 3 PORT 2 LK/ACT 10/100 LK/ACT LK/ACT 10/100 PORT4 PORT 1 POWER S14 & PS14P (PoE) Convenient Switches PORT 1 Fig2.2a. Magnum S14, Front view (three RJ-45 ports on Front 10/ 100 9VDC. 1AMP 8 WWW.GarrettCom.Com GarrettCom Magnum S14 Convenient Switch side of the unit, as shown in Fig GarrettCom S14 –15V DC Fig. 2.2b Fig2.2b.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) The Yellow label S14 shown above are for office and wiring closet environments and use an external AC power supply. A metal case with convection cooling is featured. Operation may be in 0° to 50°C ambient temperature. The units can be mounted securely on a closet wall or metal cabinet, or by using the metal panel mounting clips included. The orange-label Magnum S14H as shown above in Fig 2.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Ambient temperature rating is up to –25°C to +60°C for any of the power input types, AC F/H PWR 3 LA3 10/100 LA4 GarrettCom F/H + 4 - 8 – 15V DC PORT 2 LK/ACT 10/100 2 PORT 3 10/ 100 PORT 3 PORT 2 LK/ACT 10/100 LK/ACT LK/ACT 10/100 PORT4 PORT 1 POWER or DC. GarrettCom S14 Left Side View Fig 2.2d 10/ 100 9VDC. 1AMP PORT 1 1 Magnum S14H Hardened Convenient Switch LA2 LA1 PORT 4 WWW.GarrettCom.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) F/H PWR 3 LA3 10/100 PORT 2 LA1 1 PORT 1 WWW.GarrettCom.Com GarrettCom Magnum S14P Premium Rated Convenient Switch Fig. 2.2e options include panel-mounting, DIN-rail, or rack-mount tray. Choices of models for external AC or internal DC powers 10/ 100 9VDC. 1AMP Magnum S14P Premium Rated Convenient Switch extended temperature components, the S14P uses similar thermal techniques as the S14H hardened units for cooling.
S14 & PS14P (PoE) Convenient Switches 2.2.1: Installation and User Guide (01/06) Magnum PS14P : 4-port PoE Power Source Switch GarrettCom’s continuous efforts of designing reliable and premium-rated Industrial Ethernet products with the latest technology while being a cost effective solution has successfully yielded their first Industrial PoE switch called the Magnum PS14P Convenient Switch.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) PS14P’s Ethernet ports can provide Power as well as 10/100 Mb data transmission over the inter-connecting Ethernet cables. So a single Ethernet twisted pair cable will be able to transmit voice, data and power from the attached devices. The PS14P switches are Power Sourcing Equipment (PSE), and are fully compatible with Powered Devices (PD)(e.g wireless access points, IP phones) that comply with the IEEE 802.3af PoE standard.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) successfully The PS14P is a standards-compliant way to power and connect a few small Ethernet devices at the edge of a network where AC power is not cost-effective to deploy.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) These are applications where the Magnum PS14P can be used to provide the power and data for these PoE Powered Devices, which require 12-13watts maximum. - Wireless LAN access points and WLAN Mobility system - VOIP phones - Remote Security Camera - SNTP Clock - Factory floor and building control monitoring (Temperature, Smoke, Heat and other environmental sensors).
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Because of the approval of 802.3af PoE standard, the RJ-45 Ethernet jack will become the first worldwide standard power plug. The futuristic applications of PoE look promising as a convenient point (providing Notebook computer, Cell phone charger, and PDA games through the PoE devices).
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Source Convenient Switch models come with two (2) sets of LED indicators. One set is mounted in the end adjacent to three of the RJ-4 ports for easy viewing when the unit is mounted in a rack mount tray. The Magnum PS14P Power Source Switch requires a heavy-duty power supply of 48VDC 1.4Amps (66 watts total consumption) to provide 13-15w power on each port to the PoE unit.
S14 & PS14P (PoE) Convenient Switches Note: Installation and User Guide (01/06) The 8-15vdc option is also present, but can only be used to power the PS14P unit when no PoE devices are attached. While using a 12vdc Adaptor to power on the switch, the unit will not function as a PoE power source switch but as a non-PoE switch only. 2.3 Magnum PS14P & S14-Series, with four (RJ-45) Copper ports The Magnum S14-Series & PS14P chassis house one main PC board.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) and Activity (LK/ACT) LEDs indicating traffic that are mounted on the top of the unit as well as the end. LEDs mounted next to each port indicate (LK/ACT as LA1, LA2, LA3, LA4), 10/100 (ON for 100Mbps), and full/half duplex (F/H is ON for full duplex). The DC power plug connector or “jack” is in the right rear of the chassis. The internal DC input terminal block is also provided on the rear side of the unit. 2.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) While other switching technologies such as "cut-through" or "express" impose minimal frame latency, they will also permit bad frames to propagate out to the Ethernet segments connected. This "cut-through" technique permits collision fragment frames, which are a result of late collisions, to be forwarded which add to the network traffic.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) buffering and processing resumes. This flow-control sequence occurs in a small fraction of a second and is transparent to an observer. See Section 4.6 for additional details. Another feature implemented in Magnum S14-Series & PS14P(PoE) Convenient Switches is a collision-based flow-control mechanism (when operating at half-duplex only).
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 2.5 Features and Benefits Small 4-port 10/100 Switch unit for edge-of-network applications Expansion of Ethernet connectivity is needed to connect edge devices into the LAN, the Magnum S14-Series & Switches provide 10/100 switching in a convenient and compact package that fits right into the site.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Installation is “Plug and Play”, operation is transparent to software The Magnum S14-Series & PS14P Switches operate as LAN switches only forwarding those packets from each domain that are needed on the other domains. Internal address tables are self-learning. All ports are autocross. Two sets of LEDs for viewing status from any angle.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) AC and DC Power Supplies with extended temperature ratings S14-Series power input may be a variety of types, external AC and internal DC at 12V, 24V, or -48VDC. AC may be at extreme temperatures. DC-input models can operate as dual-source (S14-series) The 12V DC jack is present on DC-input models, so that the unit can operate from an external AC PS, or from DC applied to the terminal block, either or both present.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Efficient Compact design, for all-purpose convenient mounting Featuring a compact metal case, Magnum S14-Series & PS14P(POE) can be installed in minimal space in a rack-mount MC14-TRAY, on DINRail (optional) or panel mounting. 2.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) of 10 Mbps and 100Mbps users. The switching full / half duplex capability on all four ports provide bandwidth for high performance. Port #1 (on the back end) is typically used for an up-stream connection. When expansion is needed, add another S14 and connect it into port #1 with twisted pair cabling to add 3 more ports. Example 1.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Magnum 6K25 LA3 F/H PWR LA1 1 Magnum S14 Convenient Switch LA2 PORT 2 10/100 LK/ACT GarrettCom PORT 4 LA3 9VDC. 1AMP LA3 F/H PWR WWW.GarrettCom.Com GarrettCom Magnum S14 Convenient Switch GarrettCom Magnum S14 Convenient Switch 100 Server 12V, 1.5Am ps Magnum DS80C Dual Speed Personal Hub Po wer PORTS 1SW F/H PORT S F/H GARR ET T Lin k/Act Speed Error GARRET T Link/Act Speed Error LA2 1 10/ 100 9VDC.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Mbps. High performance users need a high bandwidth up-link for access to a central LAN and central file servers. Any attached node can change speed at any time without affecting network operation or impacting other users. The multi-functional S14 Convenient switches provide this solution very efficiently and economically.
LA3 F/H PWR F/H PWR LA3 3 LA2 10/100 LK/ACT 10/100 LK/ACT PORT 3 PORT 2 PORT 1 GarrettCom IBM Compatible Magnum S14 Convenient Switch IBM Compatible PORT 1 WWW.GarrettCom.Com 1 10/ 100 9VDC. 1AMP PORT 4 F/H X 2 3 6 8 7 8 PORT 2 PORT 3 X 3 1S W 1 H 2 3 4 4 5 6 5 7 8 6 7 8 PORT 1 PORT 2 PORT 3 100Mb Servers and Workstations PORT 1 LA3 LA2 10/ 100 WWW.GarrettCom.Com PORT 1 GarrettCom Magnum S14 IBM Compatible Convenient Switch 10/ 100 9VDC. 1AMP WWW.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Built with high-grade components, efficient thermal techniques of cooling, and equipped with a wide variety of options of AC and DC power supplies, the cost-effective Magnum S14Hs Convenient Switches easily qualify to be used in highly controllable industrial applications. The S14H Switches act as a network edge connectivity unit to satisfy ongoing needs very efficiently and economically.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Magnum 6K25 W W W .G a rr e ttC o m .
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) mounted above the ceiling in the building. The steel enclosure and wide selections of DC power inputs qualifies the Magnum S14Ps to provide a dependable, reliable and economical solution for any temperature un-controlled environments. This sleek designed convenient Switch can easily meet the ongoing demand of a growing network. Example 4a.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Magnum WWW.GarrettCo GarrettCom Magnum 6K25 10/100/1000 Configurable Ethernet Switch 1 L P 1 L 1 L 0/ K/ O 0/ K/ 0/ K/ W A PORT PORTPORT P O R P F/W L H A P O R PORT Magnum S14 Convenient SwitchP -48vdc power Video L 1 L 1 L P 1 K/ 0/ K/ 0/ K/ O 0/ A A W PORT PORTPORT P O R P O R P O R PORT Magnum S14 Convenient SwitchP 1010 / 0 1 L P 1 L 1 L 0/ K/ O 0/ K/ 0/ K/ AW PORT PORTPORT P O R WWW.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) The PS14P(PoE) is being recommended to fulfill this requirement to make the upgrade more cost-effective and avoid another un-necessary electrical cable expansions. The sleek industrial proof Magnum PS14P(PoE) with its power Source Switch capability, easily meets the demand to provide power through its RJ-45 cable, and allows for a very neat Network setup.
S14 & PS14P (PoE) Convenient Switches NCM Installation and User Guide (01/06) NEA PLC PLC SCADA Magnum 6K25 SCADA WWW GarrettC -48vdc power PW LA F/H R 3 POR P O POR POR P O LA 1 POR Magnum S14 PW LA F/H R 3 POR P O POR POR Router P O GarrettCo L1 K 0/ LA 2 Convenient Switch P O P O 9 V D C P O 10/100 GarrettCo L1 K 0/ LA 1 POR Magnum S14 IBM LA 2 Convenient Switch P O -48vdc power 9 V D C 10/ IBM IBM IBM IBM Wireless points Workstatio 48vdc power IBM IBM PS14P Po
S14 & PS14P (PoE) Convenient Switches 3.0 Installation and User Guide (01/06) INSTALLATION This section describes the installation of the Magnum S14-Series & PS14P(PoE) Convenient Switches, including location, mountings, power supply and media connection. 3.1 Locating the Convenient Switch Unit All the S14-Series & PS14P(PoE) Switches operate in transparent half-and full-duplex mode.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) associated cabling. Make sure the unit is installed in a location that is easily accessible to an AC power outlet or power strip and where convection cooling is not inhibited. The green Power (PWR) Led must turn ON when power is applied through the internal DC input 12V, 24V or –48V DC or external AC through 9V DC jack. 3.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) the front. Any mix of the Convenient Switches, Media Converters may be placed on a tray, up to a maximum of 16 units. (The mounting spaces of the MC14-TRAY are specific to the “S14”-series, and do not permit other models).
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) and supporting up to 10 Switches for MC14-TR+PS9 and 16 units S14-Series for MC14TR+PS9X2. The MC14-TR+PS9X2 Model has two groups of eight units per power supply. These models are equipped with auto-ranging AC input to the power supplies for use worldwide.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) installation of the model MC14-TR+PS9, 19” rack-mount tray, holding a few S14-Series , 10Mbps FT14’s and 100Mb 14E Media Converters, each with their power input plugged into the built-in common AC power supply in the rear area of the tray. (PS units that come with the MC’s are not used). Metal mounting screws in the bottom-front hold each of the media converters secure in the tray, separately removable for service.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 3.4 DIN-Rail mounting option The Magnum PS14P, S14HR & S14PR Convenient Switches, designed for use in “Factory Floor” Industrial Ethernet environments, are also available for DIN-Rail mounting in an enclosure having DIN Rails. The metal DIN-Rail mounting hardware is optional and needs to be ordered as a separate item, e.g. Model # DIN-RAIL-MC2. It comes with four screws to attach the bracket to the MC unit.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) bracket The Magnum S14 Models with “HR” have 24VDC power, and have the DINRail-MC2 bracket included and assembled with the MC unit at the factory. 3.5 Power Requirements, Power Supply Types for S14-Series Switches Magnum S14-Series Switches are power-efficient and can work with an external AC power supply. Magnum S14-Series require a nominal 12VDC input (range 8 to 15V, see Specifications) at the jack in the rear.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) The S14-Series are designed to provide reliable operation, withstand higher temperature environments, and provide the Direct DC power choices to the user to deploy in uncontrolled temperature environments. 12VDC 24VDC -48VDC The Internal 12V DC (8 – 15V DC) has a built-in terminal block for +, -, ground. The 9V DC jack is also present.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 3.6 Powering the S14H & S14P (DC internal) with 12V, 24V or –48VDC power input Each Magnum S14H/S14P is reliably equipped with a Direct DC power supply, and have built-in screw terminals for secure attachment of the power leads. Three models support a range of power input types. The three model choices are for use with 12VDC, 24VDC or -48VDC power. DC power input may be chosen for high-availability.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) present and optionally can be used with an external P-rated AC power supply to provide “dual source” power input. DC Power Terminals: “+”, “-”, floating GND: Terminal for “earth” or ground wire connection to the S14H chassis Input Voltage: 8 - 15V DC (12V DC) 18 – 36V DC (24V DC) 36 – 60V DC (-48V DC) Input current: 0.8 amp.(12V DC) 0.4 amp max.(24V DC) 0.2 amp max.(-48V DC) Power Consumption: 3 watts typical, 4 watts max. www .
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 3.7 S14H & S14P, DC-powered, -48VDC, 24VDC and 9VDC Installation This section describes the proper connection of the -48VDC leads (or 24VDC, 12VDC leads) to the Direct DC power terminal block on the Magnum S14H hardened media converter (as shown in Figure above). The DC terminal block on the Magnum S14H is located on the left side of the unit and is equipped with three (3) screw-down lead posts.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) The connection procedure is straightforward. Simply insert the DC leads to the S14H’s power terminals, positive (+) and negative (-) screws. The use of Ground (GND) is optional; it connects to the S14H chassis. Ensure that each lead is securely tightened from the top, as shown here. NOTE: Always use a voltmeter to measure the voltage of the incoming power supply and figure out the +ve potential lead or -ve potential lead.
S14 & PS14P (PoE) Convenient Switches 3.7.1 Installation and User Guide (01/06) Power Requirement for Magnum PS14P(PoE) Power Source Switch POWER INPUT: Total Power Consumption: 66 watts max. (1.4A @48VDC) Terminal block for -48v DC input (range of 46 to 60V dc), built in for +, - , ground. Note: The 8-15V DC option is also present, but can only be used to power the PS14P(POE) unit when no PoE devices are attached.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 3.8 Connecting Twisted Pair (RJ-45 ports) The Magnum S14-Series & PS14P(POE) Convenient Switches can be connected to only one media type with two different speed i.e. 100BASE-TX and 10BASE-T. CAT 5 cables should be used when making 100BASE-TX connections. When the ports are used as 10BASE-T ports, CAT 3 may be used. In either case, the maximum distance for unshielded twisted pair cabling is 100 meters (328 ft).
S14 & PS14P (PoE) Convenient Switches 3.8.1 Installation and User Guide (01/06) Connecting Twisted Pair (RJ-45, CAT 3 or CAT 5, Unshielded or Shielded) The following procedure describes how to connect a 10BASE-T or 100BASE-TX twisted pair segment to the RJ-45 port. The procedure is the same for both unshielded and shielded twisted pair cables. 1. Using standard twisted pair media, insert either end of the cable with a RJ-45 plug into the RJ-45 connector of the port.
S14 & PS14P (PoE) Convenient Switches 3.8.2 Installation and User Guide (01/06) Connections to NICs which support Auto-Negotiation, RJ-45 ports The copper ports of Magnum S14-Series Convenient Switches will function properly with NICs (Network Interface Cards) which support Auto-Negotiation, and the Fast Link Pulse (FLP) coding for the 100BASE-TX signaling system.
S14 & PS14P (PoE) Convenient Switches 4.0 OPERATION Installation and User Guide (01/06) 4.1 Dual-Speed Functionality, and Switching The Magnum S14-Series & PS14P(PoE) Convenient Switches provide four switched ports(three ports in the front and one on the rear). The architecture supports a dual speed switching environment, with auto-negotiation capability. The switched RJ-45 ports are full-duplex and auto-sensing for speed. (See section 2.2).
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Switching, Filtering and Forwarding Each time a packet arrives on one of the switched ports, the decision is taken to either filter or to forward the packet. Packets whose source and destination addresses on the same port segment will be filtered, constraining them to one port and relieving the rest of the network from processing them.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Switching, Address Learning The Magnum S14-Series & PS14P(PoE) units have address table capacity of 2K node addresses, and are suitable for use in large networks. They are self-learning, so that as nodes are added or changed, the S14-Series & PS14P(PoE) automatically keeps up with node locations. An address-aging algorithm causes least-used addresses to fall out in favor of new frequently-used addresses.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) switches where the switch manager fixes the port settings via software, and the result of the auto-negotiation is changed in the managed switch by the manager commands. In such cases, the 10/100 speed or the F/H mode may be affected, but auto-cross in the S14 and PS14P(PoE) Switches will still work. The auto-cross function cannot be disabled.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 4.3: Dual LEDs, Front-panel and side-panel (Magnum S14-Series & PS14P(PoE)) LED Description PWR Illuminates GREEN to indicate power applied. LK/ ACT Steady ON for LINK w/no traffic, blinking for activity per port. LINK will turn off in the event connectivity is lost between the ends of the twisted pair segment or a loss of power occurs in the unit or remote device. The Link ports are also represented by LA1, LA2, LA3, & LA4.
S14 & PS14P (PoE) Convenient Switches 5.0 TROUBLESHOOTING Installation and User Guide (01/06) All Magnum Ethernet products are designed to provide reliability and consistently high performance in all network environments. The installation of Magnum S14-Series & PS14P(PoE) 10/100 Mb/s Switches is a straightforward procedure (see INSTALLATION, Section 3.0); the operation is also straightforward and is discussed in Section 4.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 5.1 Before Calling for Assistance 1. If difficulty is encountered when installing or operating the unit, refer back to the Installation Section of the applicable chapter of this manual. Also check to make sure that the various components of the network are interoperable. 2.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) the Magnum S14-Series & PS14P(PoE) Switch and its associated cables are functioning properly. 5. If the problem continues after completing Step 4 above, contact your supplier of the Magnum S14-Series & PS14P(PoE) 10/100 Mb/s Switch unit or if unknown, contact GarrettCom, Inc by fax, phone or email (support@garrettcom.com) for assistance. 5.2 When Calling for Assistance Please be prepared to provide the following information. 1.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 3. It is useful to include other network equipment models and related hardware, including Convenient computers, workstations, terminals and printers; plus, the various network media types being used. 4. A record of changes that have been made to your network configuration prior to the occurrence of the problem. Any changes to system administration procedures should all be noted in this record. 5.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) Packing List Number (or Sales Order Number) Date of installation Failure symptoms, including a full description of the problem. GarrettCom will carefully test and evaluate all returned products, will repair products that are under warranty at no charge, and will return the warranty-repaired units to the sender with shipping charges prepaid (see Warranty Information, Appendix A, for complete details).
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) 1. Package the unit carefully. It is recommended that you use the original container if available. Units should be wrapped in a "bubble-wrap" plastic sheet or bag for shipping protection. ( You may retain all connectors and this Installation Guide.) CAUTION: Do not pack the unit in Styrofoam "popcorn" type packing material. This material may cause electro-static shock damage to the unit. 2.
S14 & PS14P (PoE) Convenient Switches Installation and User Guide (01/06) APPENDIX A: WARRANTY INFORMATION GarrettCom, Inc. warrants its products to be free from defects in materials and workmanship for a period of three (3) years from the date of shipment by GarrettCom.
