CATERER 4 & 6 BURNER BBQ Model No. BQ1050 Model No. BQ1051 Ideal heavy duty BBQ for sporting and social clubs or anywhere large groups are entertained Solid 5mm thick steel hotplate Castors for easy moving Stainless steel burners Removable lid that doubles as a windshield Foldable side shelves Propane Gas Gas Certified to Australian and New Zealand Standards Important: Retain these instructions for future use. Gasmate® is a registered trademark of: Sitro Group Australia Pty Ltd www.gasmate.com.
CONTENTS GENERAL INFORMATION Gas Installation Codes Section Page General Information 2-4 Parts List & Hardware List 5-6 Assembly Instructions 7-11 • B arbecues for use with bottled gas are labelled ‘Propane Gas’. Care & Maintenance 12 Lighting Procedure 13 Burner Operation & Operating Procedure 14 • B arbecues for use with natural gas are labelled ‘natural gas’ and must be installed by an authorised person. Check the gas type sticker attached to the barbecue.
Gas Cylinder Use & Safety FOR YOUR SAFETY This is a low pressure barbecue and must only be used with the hose and regulator supplied. Your barbecue is designed for use with 4.5Kg or 9Kg gas cylinders certified to AS 2469. • Do not store empty or full spare gas cylinders under or near this or any other appliance. The gas cylinder should be filled by a reputable gas supplier and visually inspected and re-qualified at each filling.
WARNINGS • Do not test for gas leaks with an open flame • If this information is not followed exactly, a fire causing death or serious injury may occur. • Failure to comply with these instructions could result in a fire or explosion which could cause serious bodily injury, death or property damage. • Do not store a spare gas cylinder under or near this barbecue. Never fill the cylinder beyond 80% full. This barbecue is only to be used and stored outdoors. • Accessible parts may be very hot.
COMPONENTS - 4 BURNER No. Description QTY No.
COMPONENTS - 6 BURNER No. Description QTY No.
HARDWARE M6x40mm (x12) M6x12mm (x6) M5x12mm (x8) M6 Shoulder Screws (x8) IMPORTANT: Remove any transit protection material before use. TOOLS: Phillips Head Screwdriver Adjustable Spanner ASSEMBLY INSTRUCTIONS STEP 1 Attach the legs to the body using 8 x M6x40mm screws ensuring the side shelf nutserts (circled) are on the outer edge of the legs and the lower support beams using 4 x M6x40mm long screws. Screw the castors into the legs as shown.
STEP 2 Attach the handles to the top of the legs using 8 x M5x12mm long screws, then attach the cylinder hanging hook, heat shiled and fat cup holder as shown using 4 x M6x12mm long screws.
STEP 3 Attach the folding side shelves as shown using 8 x M6 shoulder screws.
STEP 4 Attach the handle to the lid ensuring the lid hook is oriented as shown on the underside using 2 x M6x12mm screws. The lower wire rack and warming rack can be installed as required.
STEP 5 The completed assembly. Note: Before use always leak test the connection to the gas cylinder and appliance using a soapy water solution. If bubbles are present, tighten and then re-test the connection.
CARE & MAINTENANCE GENERAL ASSEMBLY Care & Maintenance Connecting & Disconnecting to Gas Source As with all appliances, proper care and maintenance will keep them in top operating condition and prolong their life. Your new gas barbecue is no exception. By following these cleaning procedures on a timely basis, your barbecue will be kept clean and working properly with minimum effort. Familiarise yourself with the general information and safety guidelines located at the front of this manual. Check 1.
LIGHTING PROCEDURE WARNINGS Burner Operation & Ignition System Check 1. With cylinder valve in ‘OFF’ position push and turn the far left or right control knob anti-clockwise to `HIGH’. Check for sparking to the burners. • Before connecting and disconnecting barbecue to gas source, make sure burner controls are in ‘OFF’ position. 2. If spark is not evident at the burner ignition point, check for any loose leads at either the electrode or the ignition pack.
BURNER OPERATION & IGNITION SYSTEM CHECK Problem Burner will not ignite Food is not cooking or is taking too long Possible Reason Solution Valve on gas bottle closed Open valve on gas bottle Control knob is closed Turn knob to high when lighting Igniter is faulty Use a long barbecue match.
SAFE APPLIANCE LOCATIONS Within a partial enclosure that includes an overhead cover and no more than two walls (see Example 2 & 3). This appliance shall only be used in an above ground open-air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection.
For any queries or assistance call Customer Service (Australia Only) 1300 174 876 Hours of operation: Monday to Friday 8am - 5pm EST Do not return to place of purchase. Keep your purchase receipt, this will be required to make any claims under the 12 month warranty.
