User Manual

ManualsBrandsGasmate ManualsHeatersStellar Black Flame Heater

Important: Retain these instructions for future use

Model No. FH200ODS

03908 04/19

Gasmate® is a registered trademark of: Sitro Group Australia Pty Ltd www.gasmate.com.au

Aber Living, N.Z. www.gasmate.co.nz

FOR YOUR SAFETY

If you smell gas:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂame.

3. If odour continues, immediately call your gas supplier.

Do not store or use gasoline or other ﬂammable vapour

and liquids in the vicinity of this or any other appliance.

WARNING

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

Read the instructions thoroughly before installing or

servicing this equipment.

FOR OUTDOOR USE ONLY

PROPANE GAS

The ideal solution for extending the season of

outdoor entertaining

Push button electronic ignition

Includes a safety ‘tip-over’ switch that halts supply of

gas to the unit should it be accidentally knocked over

Oxygen depletion system for enhanced safety

Complete with hose and POL regulator

Efﬁcient and powerful 33MJ/h output

Adjustable heat output

Operates for approximately 14 hours on a properly

ﬁlled 9Kg Propane cylinder

For outdoor use only

Gas certiﬁed to Australian standards

STELLAR BLACK

FLAME HEATER

Summary of content (12 pages)

PAGE 1
STELLAR BLACK FLAME HEATER Model No.
PAGE 2
INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Prior to assembling your appliance, the following must be reviewed. Compliance with the following should result in satisfactory heater operation. This instruction manual should be retained for future reference. The installation must conform with local codes or authority having jurisdiction. IMPORTANT SAFETY RULES This appliance must only be used in a well ventilated area. 1.
PAGE 3
d. The flame should be visually checked whenever heater is operated. If flames extend beyond surface of the chimney or black spot is accumulating on the burner or glass, the heater should be turned off immediately. The heater should not be operated again until the unit is serviced and or repaired. POL CYLINDER CONNECTION DEVICE e. Any cleaning agent used on the appliance should be of a non-combustible and non-corrosive nature. 7.
PAGE 4
PARTS LIST 1. Middle Plate 1pc 2. Control Box 1pc 3. Bottom Panel 1pc 4. Lower Support Leg 4pcs 5. Upper Support Post 4pcs 80cm Long Rubber Foot 7. Lower Plate 1pc 6. Upper Plate 1pc 8. Glass Tube 1pc Pre-assembled in Middle Plate 11. Protection Guard 4pcs 12. Guard Fixing Bracket 4pcs 9. Radiant Head 1pc 10. Reflector 1pc Pre-assembled in Upper Plate 13. Side Panel 3pcs 14. Front Panel 1pc 15. Screw 67pcs All pre-assembled in relative parts 16. Knob 1pc 17.
PAGE 5
ASSEMBLY INSTRUCTIONS Note: Remove any transit protection material. Tools required: Phillips head screw driver and 2 adjustable spanners. STEP 1 The lower support leg has a rubber foot at the bottom. Remove the five screws from each leg, using them to attach the bottom panel and middle plate from the inside. Ensure the magnets on the side of the middle plate are aligned with the ‘T’ shaped holes on the side of the bottom panel.
PAGE 6
STEP 3 Attach the control box to the underside of the middle plate with the controls facing the magnets, using 4 screws from underneath. Unscrew and remove the igniter cap, insert a ‘AA’ battery with the + facing outwards, then re-attach the cap. STEP 4 Carefully slide the glass tube up into the radiant head, ensure the rubber ring is located onto the glass tube and also at the bottom of the tube and lower it into the hole in the middle plate.
PAGE 7
STEP 5 Attach the reflector to the studs on the radiant head using the washers and wing nuts supplied. STEP 6 Attach the side and back panels using the 4 screws supplied per panel.
PAGE 8
STEP 7 Attach the guards by aligning the hooks with the slots in the upper support posts and secure at the top with the bracket and screw supplied. STEP 8 Attach the knob to the outside top of the door panel with the chain on the inside. The bent tabs at the bottom are positioned into the ‘T’ shaped holes in the bottom panel and held at the top with magnets.
PAGE 9
OUTDOOR FLAME HEATER - FOR OUTDOOR USE ONLY 650mm Hose connection point 700mm 1950mm 800mm Minimum Clearance from Combustible Surfaces*: 500mm *Combustible materials are considered to be wood, compressed paper, plant fibres, plastic or other materials that are capable of being ignited and burned.
PAGE 10
OPERATION Insert a ‘AA’ battery with the ‘+’ facing outwards. Connect hose POL to cylinder and leak test before use (Cylinder not included) LIGHTING INSTRUCTIONS STEP 1 Ensure that the control knob is OFF. Slowly open the gas cylinder valve. STEP 2 Press and turn the control knob to LIGHT position, push the igniter to generate spark while keeping control knob pressed in. STEP 3 Check for the pilot flame through glass tube.
PAGE 11
TROUBLE SHOOTING Problem Main burner will not light Pilot will not stay on Possible Causes Solution Gas valve may be OFF Turn the gas valve ON LPG cylinder empty Refill LPG cylinder Orifice blocked Clean or replace orifice Air in supply system Purge air from lines Loose connection Check all fittings Debris around pilot Clean dirty area Loose connection Check all fittings Thermocouple faulty Replace thermocouple Gas leak in line Check connections Lack of gas pressure LPG cylinder is n
PAGE 12
SAFE APPLIANCE LOCATIONS This appliance shall only be used in an above ground open-air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection. Any enclosure in which the appliance is used shall comply with one of the following: An enclosure with walls on all sides, but at least one permanent opening at ground level and no overhead cover (see Example 1).