Vertical Gas Smoker Model No. GM160-018 FOR OUTDOOR USE ONLY - OPERATES ON LPG Retain these instructions for future use. Important: The installer or seller must leave these instructions with the consumer.
GENERAL INFORMATION Gas Installation Codes • mokers must be used in accordance with AS/NZS S Standard 5601 “Gas Installations”. • S mokers for use with bottled gas are labelled LPG/ULPG. • S mokers for use with natural gas are labelled ‘natural gas’ and must be installed by an authorised person. Check the gas type sticker attached to the smoker. Failure to comply with these instructions could result in a fire or explosion which could cause serious bodily injury, death or property damage.
GENERAL INFORMATION Location of your Smoker Check Smoker for any Damage DO NOT use your smoker in garages, porches, sheds, breezeways, or other enclosed areas. Your smoker is to be used OUTDOORS only. DO NOT use this smoker in a manner other than its intended purpose. It is NOT intended for commercial use. The smoker is not intended to be installed in or on recreational vehicles and/or boats. The smoker is not to be used as a heater.
GENERAL ASSEMBLY • DO NOT wear loose clothing while operating the smoker. Tie back long hair while operating the smoker. ALWAYS wear fully-covering shoes while operating the smoker. • Allow the smoker and its components to cool completely before conducting any routine cleaning or maintenance. • NEVER use glassware, plastic, or ceramic cookware on or in your smoker.
EXPLODED DIAGRAM PARTS LIST Make sure you have all items listed under PARTS LIST and HARDWARE CONTENTS before you begin the assembly process. No. Description Qty No. Description Qty No.
ASSEMBLY INSTRUCTIONS Before assembling the smoker, read these Instructions carefully. Assemble the smoker on a flat, clean surface. The smoker is heavy. NOTE: Do not fully tighten all the nuts during the initial stages of assembly. 18 Caution: Sheet metal can cause injury. Wear gloves18 when assembling the smoker. Tools required: Philips head screwdriver (or cordless drill and bits). AA 18 18 19 19 19 Flat head screwdriver. 19 Adjustable spanner.
ASSEMBLY INSTRUCTIONS Step 3 Remove the air vent handle, then slot through opening in rear of cabinet. Secure using 4 x M6 x 12 screws (AA) and 4 x M6 tailor-made screws (CC) to assemble the air vent (E). Then re-attach the air vent handle. CC AA 1 30 CC AA 1 30 30 30 Step 4 Attach the side carry handles (4) to each side of the cabinet using the holes provided. Secure with 8 x M6 x 10 screws (DD), 8 x washers (GG) and 8 x M6 nuts (FF).
ASSEMBLY INSTRUCTIONS Step 5 Remove the pre-assembled screws and attach the upper door handle (11) by inserting it through the holes in upper door (8). Secure door handle bracket to the inside of the door. 11 11 screw screw 螺钉 8 8 螺钉 Step 6 Repeat Step 5 to attach the lower door handle (11) to the lower door (12).
ASSEMBLY INSTRUCTIONS Step 7 Attach the door hinges (4) using 8 x M6 x 40 screws (EE) to the side of the cabinet as shown. 4 4 EE EE Step 8 Use 8 x M6 x 40 screws (EE) to assemble the upper door (8) and lower door (12) to the hinges.
ASSEMBLY INSTRUCTIONS Step 9 Insert the support racks (3) into the four slots on each side of the inside of the upper cabinet and angle downward until they sit flat as shown. 3 3 Step 10 Slide the cooking grills (17) into the support racks as shown.
ASSEMBLY INSTRUCTIONS Step 11 Slide the water/wood chip tray (27) into the lower cabinet as shown. 27 Step 12 27 Use 1 x M6 x 12 screw (AA) to secure the regulator hose fastener (26) onto right front leg. Locate the hose through the fastener to secure the hose above the ground. By securing the hose it prevents the hose from coming in contact with the hot burner assembly. Locate the S-hook (28) onto the right side carry handle. When the smoker is not in use, hang the hose/regulator from the side handle.
ASSEMBLY INSTRUCTIONS Step 13 Use 1 x M5 x 20 screw (HH) to secure the match holder (25) to the bottom of the side panel of the smoker as shown. HH HH HH 25 25 25 Step 14 29 29 29 Remove the pre-assembled latch screws, then assemble the latches (29) as shown.
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS STEP 15 STEP 16 Ensure cylinder valve is in its full ‘CLOSE’ position. Check for any damage to either the cylinder connection or the hose. NEVER attempt to use damaged equipment. Attach the regulator and hose to your gas cylinder. Tighten the nut to a positive stop by hand. Turn on the gas cylinder ensuring that the control knob on the smoker is turned OFF at this point. DO NOT ATTEMPT TO LIGHT THE SMOKER!!.
OPERATING INSTRUCTIONS Pre-Use Procedures Adding Wood/Charcoal Before you cook food in your smoker, it is important to “season” your smoker. Seasoning seals the paint and interior of your smoker to enhance flavoring, durability, and overall performance. This is also referred to as the “breakin” process. To add wood chips before cooking, simply fill the water/ wood chip tray with your choice of flavoring hardwood chips. The amount and type of wood you use is entirely up to you.
LIGHTING PROCEDURES Igniter Lighting System: Shutting The Smoker Off 1. Perform leak test at least twice yearly or after connecting LPG cylinder. Check all connections for leaks using the “soapy water” test as explained on page 13. CAUTION: The smoker can become very hot while in use. Do not touch any portion of the smoker except for the door handle and burner control knob. It may be necessary to use protective gloves. 2. Open the smoker bottom cabinet door.
COOKING INSTRUCTIONS IMPORTANT: Before each use, clean and inspect the hose and the connection to the LPG cylinder. If there is evidence of abrasion, wear, cuts or leaks, the hose must be replaced before the smoker is used. Refer to the “leak test” instructions in the LPG cylinder connection portion of this manual. • • Fill the water/wood chip tray. First add a cup of flavouring wood chips and place the tray inside the smoker as instructed in the assembly section of this manual.
AFTER USE SAFETY AND MAINTENANCE • Use caution when lifting and moving the smoker to avoid strains or back injury. Two people are recommended to lift or move the smoker. • If rust is present on the exterior surface of the smoker, clean the area with steel wool or emery cloth and use heavy duty, heat resistant paint. • DO NOT store the smoker near gasoline or other combustible liquids or where combustible vapors may be present.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Burner will not light 1. 2. 3. 4. 5. 6. Check LPG cylinder fuel level. Bad electrode spark. Burner may not be properly seated. Burner may be obstructed. The cylinder valve may be closed. Regulator is not properly seated on cylinder valve. 1. 2. 3. 4. 5. 6. Replace LPG Cylinder. Check to see if the smoker will match light. Electrode or collector may need adjustment. Reseat burner. Clear obstructions from burner. Open cylinder valve.
SAFE APPLIANCE LOCATIONS SAFE APPLIANCE LOCATIONS This appliance shall only used an above groundground open-air situation with natural ventilation, withoutwithout stagnant areas, This appliance shallbeonly beinused in an above open-air situation with natural ventilation, where stagnant gas leakage andwhere products combustion are rapidly dispersed byare wind and natural convection. areas, gasof leakage and products of combustion rapidly dispersed by wind and natural convection.
This page has been left intentionaly blank 20
