Operating Instructions Design Fleischwolf Pro M Art.-No.
Carefully read all provided instructions before you start running the appliance and pay regard to the warnings mentioned in these instructions. Table of Contents Knowing Your Design Mincer Pro M.................................................27 Important Safeguards......................................................................28 Important Safeguards for Electrical Appliances..............................29 Moving Parts – Risks of Injuries....................................................
Dear Customer! Congratulations! A variety of new possibilities for delicious meals comes with your new mincer; even for vegetarian dishes. Effortless you mince and mix the ingredients for meatballs, vegetable burgers and minced meat. With great refinement you can prepare your own sausage specialities, or fillings for ravioli or tortellini—always really fresh! These instructions for use will inform you about the various functions and features which makes it easy to take pleasure in your new mincer.
Important Safeguards Carefully read all instructions before operating this appliance, and save for further reference. Do not attempt to use this appliance for any other than the intended use, described in these instructions. Any other use, especially misuse, can cause severe injuries or damage by electric shock, moving parts, heat or fire.
process bones, nuts, frozen foods or any other hard items. • Do not place the appliance or any part of it on or near hot surfaces (e.g. burner, heater or oven). Do not use any parts or tools of the appliance with any other device. • Do not grasp in the gear hole of the motor housing, with the appliance connected to the power supply. If you have forgotten to switch OFF the appliance, before disconnecting from the power supply, wait at least 10 seconds, before inserting the plug into the power socket again.
the edge of the table or counter. The power cord may not touch hot surfaces. Ensure that no one will pull the appliance by the power cord. Take care not to entangle in the power cord. Always grasp the plug to disconnect the power cord. Do not touch the power plug with wet hands when the appliance is connected to the power supply. • Do not place or immerse the motor housing or the power cord in water or any other liquid. Do not spill or drip any liquids on the power cord or exterior of the motor housing.
Before First Use WARNING: DO NOT let young children play with the appliance, or any part of it, or the packaging! 1. Unpack the appliance and all accessories carefully and check that no parts are damaged or missing. Tip: The pusher is hollow, and some tools may be stored in its interior. Remove the cover of the pusher (just lift it) and take out the tools. 2. Carefully remove all shipping materials and promotional materials, but DO NOT remove any warning labels or the model label.
cutter housing. Do not let the motor work continuously for more than 3 minutes. Usually, during this time, you have processed a tablet full of meat. Thereafter, switch OFF the motor for 15 minutes to let the motor cool down. It is a good idea to use this time for preparing the next portion. • Reverse operation is only intended for loosening blocked foods in the worm shaft (see: Loosing Blocked Food—Reverse Operation).
Operation WARNING: The mincer is intended for mincing food. For this, the appliance is equipped with sharp-edged knives and other electrically driven moving parts. Do not insert your hands or any foreign objects (e.g. cooking utensils) in the feed tube, or outlet of the cutter housing while the appliance is connected to the power supply, to avoid risks of injuries.
• Mincing and mixing Use the cutter blade and one of the grinding discs. Place the cutter blade on the worm shaft, the edges of the cutter blade facing upwards, and turn the cutter blade gently until it settles on the shaft. It may not protrude the brim of the cutter housing. Select a suitable grinding disc (see: Tools), and place the grinding disc onto the worm shaft. Ensure that the notch of the grinding disc fits onto the protrusion of the cutter housing.
Then place the sausage horn on the separator disc. The wide brim of the sausage horn must lie firmly on the separator disc. C D • Making Kebbe (Middle Eastern meat pâté) Use the plastic finger and the cone. Place the plastic finger on the worm shaft. The plastic finger settles into the cutter housing only in one way. Thus, ensure that the notch in the brim of the plastic finger fits onto the protrusion of the cutter housing. Then place the cone on the plastic finger.
• Preparing Cookies Use the separator disc, cookie maker and former. Place the separator disc over the worm shaft. The separator disc settles into the cutter housing only in one way. Thus, ensure that the notch in the brim at one side of the separator disc fits onto the protrusion of the cutter housing. Then place the cookie maker on the separator disc. The notch in the brim of the cookie maker must fit into the protrusion on the brim of the separator disc. Tip: the former is installed later on. 4.
Do not process frozen foods. 1. Prepare the foods for processing. Remove bones, gristle and sinews as much as possible. Cut meat into strips (about 10 cm length and 2 cm thick (see: Tips for Best Results). Assemble the mincer according to the instructions above (see: Assembling the Appliance Place a sufficiently large bowl or dish under the outlet of the cutter housing). 2. Put the meat on the tray. Connect the appliance to the power supply and switch the power switch on.
7. After processing your food, switch OFF the appliance (ON/OFF switch and power switch). Then unplug the appliance. Clean the appliance according to the instructions in section Care and Cleaning. Always clean the appliance immediately after operation. Do not leave any food dry on the appliance. Making Kebbe 1. Assemble the mincer with cutter blade and grinding disc, and mince the meat and other ingredients of the Kebbe sleeves and filling separately to the desired consistency, according to your recipe.
7. Bake the cookies according to your recipe. Solving Problems If any problems occur during operation, you will find solutions in the following table. Additionally, you can contact your vendor. Problem Possible Cause The motor does not work, The appliance is not live. the indicators are dark. Solution Insert the power plug in the power outlet. The power switch is switched OFF. Switch on the power switch. The circuit breaker activates. Press the red button at the bottom of the appliance.
The motor works too slowly. The cutter housing is blocked. Switch to reverse operation for a moment (See: Loosing Blocked Food – Reverse Operation). You push down the pusher too violently. Decrease the pressure of pushing. Too hard parts are still in the foods. Remove any hard parts before processing your foods. The food is too hard. Only process foods that have a similar consistency as meat. Cook hard vegetables before processing. Cut the food in smaller pieces.
completely (ON/OFF button and power switch), unplug and clean the appliance according to the instructions in chapter Care and Cleaning. However, if the problem persists, slow down working and cut your foods to smaller pieces, before processing in the mincer (See: Properties of Your Design Mincer Pro M). Overheat Protection This appliance is equipped with an overheat protection that will automatically shut off the appliance in case of overheating. If your appliance suddenly stops running: 1.
3. Grasp the cutter housing with one hand, then press the release button near the gear hole in the front plate of the appliance. (See: Knowing Your Design Mincer) 4. With the release button pressed, unlock the cutter housing by turning it clockwise. Then pull the cutter housing out of the motor housing. 5. Unscrew the screw ring and, thereafter, hold the cutter housing close over a plastic bowl or kitchen sink and carefully turn the cutter housing with the outlet downwards.
2. It is good a advice to re-assemble the cutter housing with cutter blade and a grinding disc before storage, (See: Assembling the Appliance) to avoid injuries by the cutter blade. 3. Additionally, you can insert some tools in the pusher. For this, remove the cover of the pusher and place the tools into the interior, as shown in the figure. Then insert the pusher in the feed tube of the cutter housing. 4. Carefully roll up the power cord without knotting or bending it.
Recipes Stuffed Kebbe Kebbe (Bebble) is a traditional Middle Eastern dish made primarily of lamb and bulgur wheat, which are minced together to form a paste. This mixture is extruded through a Kebbe maker and cut into short tubes that can be stuffed with a minced meat mixture, the ends pressed together and then fried.
Index |A| abroad operation.................................. 29 accessories..................................... 28, 42 assembling........................................... 33 |B| blade.................................................. 27 buttons..................................... 27, 31, 40 |C| care and cleaning........................... 41, 42 cone........................................ 27, 35, 36 cookie maker.................................. 27, 38 cutter blade....................................
Notizen/Notes 46
GASTROBACK GmbH Gewerbestraße 20 . D-21279 Hollenstedt / Germany Telefon +49 (0)41 65/22 25-0 . Telefax +49 (0)41 65/22 25-29 info@gastroback.de . www.gastroback.
