Double Security Door

ManualsBrandsGatehouse ManualsSecurity Doors91843032

202220986-1219

Security Double Door Installation Instructions

Spanish en el reverso

PART DESCRIPTION QTY

A Security Double Door 1

AA 4 inch one-way screws 9

BB Top Bar 1

CC One-way tool 1

DD Cane-Bolt kit 1

EE End Cap 2

NOTE: All parts not shown at actual size. Handle set and lock bolt

sold seperately.

PREPARATION

Tools Recommended for Assembly

Drill 3/16” bit, level or string plumb, and pencil.

IMPORTANT: Read all instructions carefully

before starting installation.

NOTE: One-way screws are non-removeable once installed.

Questions, problems, missing parts?

Before returning to your retailer, call

our customer service department at

1-800-222-3667.

ASSEMBLY INSTRUCTIONS

FIGURE 1

Top Bar

Operating Door Stationary Door

Hinge Bar

(pre-attached)

FIGURE 5

FIGURE 2

FIGURE 3 FIGURE 6

FIGURE 4

1. Identify which side

the operating door is

located on. It can be

on either the left or

right side. Operating

door includes the

handle set lock box

(Fig. 1).

5.With the stationary door in the closed

position, position the operating door

(the one with the locksets installed)

over the remaining opening with the

lock bolt extending and protruding

into the respective holes in the

stationary door (Fig. 5).

Repeat steps 3 and 4 for the

operating door.

2. Attach your choice of locksets

(2-3/8” backset). Fully extend

the lock bolt into the “Locked”

position.

6. Insert end caps in ends of header

(Fig. 6).

Leaving approximately 1/8-in space

above the doors, mount the top bar

at top of door using the one-way tool

and 3 one-way screws.

3. Place the stationary door (the one

without locksets) in front of opening

at desired height, making sure that

the security door is vertical and

plumb. Determine where to drill by

marking through the pre-drilled holes

on the hinge bar with pencil (Fig. 3).

4. Pre-drill holes marked in Step 3.

Using the one-way tool, fasten the

door to the house using three one-

way screws. Tighten the one-way

screws only halfway at this time,

in case repositioning the door is

required later (Fig. 4).

ALL

WELDS ON THIS SIDE

OF THE DOOR NEED TO BE

GROUND FLUSH

1/4

TYP.

NOTE:

ALL DIMENSIONS ARE ±1/16" (1.5mm) unless

otherwise specified.

DOOR MUST CONFORM TO PS-022

1/4

TYP.

LARSON STANDARD TOLERANCE

UNLESS OTHERWISE SPECIFIED

0.000 TO 0.124: ±0.007

0.125 TO 0.499: ±0.010

0.500 TO 0.999: ±0.013

1.000 TO 1.999: ±0.017

2.000 TO 2.999: ±0.020

3.00 AND ABOVE: ±0.025

ANGULAR TOLERANCE: ±2°

LARSON MANUFACTURING CO.

SCALE: 1:10

DATE: 20 NOV 2012

UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES

918-23 FR DR STATIONARY PANEL - WELD DETAIL

BROOKINGS, SD

PART NUMBER: X

DRAWING NUMBER: 918-23 FRENCH DOOR ASSEMBLY (Sheet 5 of 7)

DRWN BY: DIX

THIS DRAWING AND ALL INFORMATION THERIN IS THE PROPERTY OF LARSON MANUFACTURING AND IS CONFIDENTIAL. IT MUST NOT

BE MADE PUBLIC OR COPIED. THIS DRAWING IS LOANED SUBJECT TO RETURN UPON DEMAND AND SHALL NOT BE USED DIRECTLY IN

ANY WAY DETRIMENTAL TO OUR INTEREST. OUR PRIOR SPECIFIC APPROVAL IS REQUIRED FOR EXPOSURE OF THIS DRAWING TO OTHERS

FOR ANY PURPOSE. ANY CHANGES TO THESE SPECIFICATIONS NEED WRITTEN APPROVAL.

DRAWING NUMBER: 918-23 FRENCH DOOR ASSEMBLY (SHEET 5)

ACCEPTANCE OF MATERIAL WILL BE BASED UPON THIS DOCUMENT ONLY.

DESCRIPTION

DATE

REV

DENOTES CRITICAL DIMENSION

Summary of content (4 pages)

PAGE 1
Security Double Door Installation Instructions Spanish en el reverso A PART DESCRIPTION 202220986-1219 AA CC AA CC QTY AA CC A Security Double Door 1 BB AA 4 inch one-way screws 9 BB BB Top Bar 1 CC One-way tool 1 BB DD CC DD Cane-Bolt kit 1 EE End Cap 2 DD DD DD NOTE: All parts not shown at actual size. Handle set and lock bolt sold seperately. EE PREPARATION Tools Recommended for Assembly Drill 3/16” bit, level or string plumb, and pencil.
PAGE 2
SECURITY DOUBLE DOOR 7. Cane Bolt Installation Instructions A. Position bottom bracket 1” from the bottom of the door as shown. Attach with two #10 x ¾” selfdrilling screws. B. Position top bracket with 3-1/2” of space between it and the bottom bracket. Attach with two #10 x ¾” self-drilling screws. E. Raise bolt until the bottom clears bottom bracket. Insert bolt into bottom bracket. Drill hole into sill to accept bolt. C. Insert short leg of the cane bolt through underside of top bracket. D.
PAGE 3
202220986-1219 PUERTA DOBLE DE SEGURIDAD INSTRUCCIONES DE INSTALACIÓN A PIEZA DESCRIPCIÓN AA CC AA CC CANTIDAD AA CC A PUERTA DOBLE DE SEGURIDAD 1 BB AA Tornillos de seguridad de 4 pulgadas (10.2 cm) 9 BB BB Barra superior 1 CC Herramienta de una sola función 1 BB DD CC DD Kit de cerradura antipalanca 1 EE Tapas de los extremos 2 DD DD DD EE NOTA: no se muestran todas las partes en el tamaño real.
PAGE 4
PUERTA DOBLE DE SEGURIDAD 7. Instrucciones de instalación del cerrojo B. Coloque el soporte superior A. Coloque el soporte inferior a 1” (2.5 cm) de la parte con 3 1/2” de distancia entre inferior de la puerta como se este y el soporte inferior. Fije ilustra. Fije con dos tornillos con tornillos autoperforantes autoperforantes N.º 10 de ¾” N.º 10 x ¾” (1.9 cm) (1.9 cm). C. Inserte la pata corta del cerrojo a través de la parte inferior del soporte superior. E.