Operating Guide

1
2
3
4
5
6
7
8
9
0
USER GUIDE
ELECTRONIC DEADBOLT
R
Sounds
Lights
Meaning
Successful Operation
Successful Programming
Operation Error
Code Input Error; System Shuts
Down for 45 seconds
Low Battery Power
Default Setting Restored
In Programming Mode
1 Beep
2 Long Beeps
3 Beeps
5 Beeps
10 Rapid Beeps
Flashes Green Once
Flashes Green Twice
Flashes Red 3 Times
Flashes Red 5 Times
Flashes Red 10 Times
Flashes Orange 3 Times
Flashes Orange Slowly
Restore Default Settings
Press
R
Note: Press the button for more than 5 seconds; the programming
is reset back to the original factory codes once you hear 3
long beeps.
After restoring default settings, you must run the door
handing identifying process (#1) again before
programming any other functions.
R
R
Reset
button
Do not use any chemical liquid or lubricating oil with additives to clean the lock body .
It will damage the surface or even mainboard.
The manufacturer warrants the product to be free from defects in material and workmanship for a period of 12
months from the original date of purchase. If you discover a defect in the product covered by this warranty, we will
repair or replace the item at our option using new or refurbished components.
EXCLUSIONS
This warranty covers defects in manufacturing discovered while using the products as recommended by the
manufacturer rather than occurred by the act of God, and damages caused by misuse, abuse, and unauthorized
modification.
LIMITED LIABILITY
The manufacturer will not be held liable for incidental or consequential losses or damages from any act of God.
Unit Interface
Battery Lid
Slide the lid to change the batteries.
Battery Holder
Four AA (1.5 V) alkaline batteries
(not included).
R Button (Reset)
Restore default settings.
Turn-piece
To lock/unlock the lockset from inside.
Programming Button
Programming button is for entering codes,
clearing errors and setting functions.
It is also used to lock the door.
Number Buttons
To enter user codes. Each user code is
Cylinder
To lock/unlock the lockset from outside.
Washer
Prevents water from permeating into lockset.
Operating Instructions
11
Troubleshooting
After installing the lockset and batteries,
the door can’t be locked and three short
beeps are emitted when you press the
Programming button.
The door-handing
identification process isn’t
yet complete.
Refer to step1.
When you are in the door-handing
identifying process, you get the red light
flashing three times, and three short
beeps.
Wrong door-handing or
change of the door-handing
in the memory.
Press the R button to restore the system
to factory default setting and re-execute
door-handing identifying process
( step 1)Refer to
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
(1) The depth of the latch
bolt hole is insufficient.
(2) The latch bolt is not
aimed at the opening
of the strike.
Although the electronic deadbolt has
been functioning normally, the latch bolt
suddenly locks up, and the turnpiece
inside can’t be rotated, not even with a
key.
First, take out one battery, then press
any button on the front panel for electric
discharge, and put the battery back in.
The latch bolt will automatically
re-detect its position.
Note: If the latch gets stuck frequently,
please check and fix the alignment of
the deadbolt latch & strike plate.
(1) Dig the latch bolt hole for the strike
(2) Adjust the strike to the appropriate
position.
deeper. The minimum depth is 1 in.
(2.5 cm).
You’ve installed the lockset and batteries,
but you still get no response when you
press any button.
Batteries were installed
incorrectly.
Check to see if the battery polarities
have been reversed or if the battery is
dead.
If so, re-install or change the battery.
If not, please check to see if the cable is
properly connected.
Low battery.
Replace with new alkaline batteries.
Although you succeeded in the first
execution of the door-handing identifying
process, the latch still doesn’t work.
(i.e. You can feel the motor attempting to
run, but the latch bolt is stuck, and the
turnpiece can’t be rotated.)
The door can be locked normally, but
when you try to unlock it, you hear three
short beeps and the lock won't unlock
when you enter the user code and press
the programming button.
Unlock the door with the key and
re-program the unit.
If the problem persists, call our customer
service department.
Warranty
Delete an Existing User Code
2
Delete All User Codes at Once
3
Default programming code (PC): 0000
Default user code (UC): 1234
Your new programming code (PC) ____________
Your new user code (UC) ___________________
The same programming code and user code cannot be accepted.
The lock will cease operation if unauthorized codes are entered more than
5 times. The system will unfreeze after 45 seconds.
DO THIS FIRST
Door Handing Identification Process
The lock needs to learn if your door is a right- or left-handed.handed
0
!
Toggle Auto-Lock On/Off
5
Note: The preset delay-time is 30 seconds. You can change the time by following the instructions
in Step 7. Repeat Step 6 to cancel the auto-locking function.
6
Set Auto-Lock Time Delay
Note: The delay time can be programmed for anywhere from 10 - 99 seconds
Toggle Mute On/Off
7
Note: Repeat Step 8 to toggle mute on and off.
LED illumination will still function when mute is toggled on.
Create a One-Time User Code 4–10 Digits Long
Enable/Disable All User Codes
Note:
The lock can only be operated by key during the time.
Repeat the steps to enable the user codes again.
Auto-locking and keypad locking functions will be invalid when user codes are disabled.
1
4
5
6
7
8
9
10
9
Note: The one-time user code will automatically expire after it is used one time.
Keep the door open while programming to avoid being locked out accidentally.
The lock contains one factory-preset user code but can be programmed to
store up to a total of six additional unique user codes.
Codes can be added and deleted at any time. For first-time programming, use factory
default programming code. It’s recommended to change the default programming code
and default user code right after you install the lock.
Operation Indicator Sounds and Lights
8
Add New User Code
1
Note: Up to 6 sets of user codes can be saved. User codes should be 4–10 digits in length.
Change Programming Code
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
4
Enter New PC.
Enter New UC.
Enter the UC
you want to
delete.
Enter
seconds
(10~99).
Enter
One Time
Code.
2
3
Note:
The lock can only be operated by key during that time.
Auto-locking and keypad locking functions will be invalid when user codes are deleted.
Enter PC.
The deadbolt latch is stuck
due to a warped door or
misaligned door.
The sensor did not sense
position.
1
1
5
5
6
6
7
7
8
8
2
2
3
3
4
4
While the door is locked, you hear the
latch bolt coming out when you press
the Programming button to lock the
door; however, three short beeps are
emitted. Conversely, while the door is
open, no beeps are emitted when
locking the latch bolt.
1
2
3
4
5
6
7
8
9
0
USER GUIDE
ELECTRONIC DEADBOLT
R
Sounds
Lights Meaning
Successful Operation
Successful Programming
Operation Error
Code Input Error; System Shuts
Down for 45 seconds
Low Battery Power
Default Setting Restored
In Programming Mode
1 Beep
2 Long Beeps
3 Beeps
5 Beeps
10 Rapid Beeps
Flashes Green Once
Flashes Green Twice
Flashes Red 3 Times
Flashes Red 5 Times
Flashes Red 10 Times
Flashes Orange 3 Times
Flashes Orange Slowly
Restore Default Settings
Press
R
Note: Press the button for more than 5 seconds; the programming
is reset back to the original factory codes once you hear 3
long beeps.
After restoring default settings, you must run the door
handing identifying process (#1) again before
programming any other functions.
R
R
Reset
button
Do not use any chemical liquid or lubricating oil with additives to clean the lock body .
It will damage the surface or even mainboard.
The manufacturer warrants the product to be free from defects in material and workmanship for a period of 12
months from the original date of purchase. If you discover a defect in the product covered by this warranty, we will
repair or replace the item at our option using new or refurbished components.
EXCLUSIONS
This warranty covers defects in manufacturing discovered while using the products as recommended by the
manufacturer rather than occurred by the act of God, and damages caused by misuse, abuse, and unauthorized
modification.
LIMITED LIABILITY
The manufacturer will not be held liable for incidental or consequential losses or damages from any act of God.
Unit Interface
Battery Lid
Slide the lid to change the batteries.
Battery Holder
Four AA (1.5 V) alkaline batteries
(not included).
R Button (Reset)
Restore default settings.
Turn-piece
To lock/unlock the lockset from inside.
Programming Button
Programming button is for entering codes,
clearing errors and setting functions.
It is also used to lock the door.
Number Buttons
To enter user codes. Each user code is
Cylinder
To lock/unlock the lockset from outside.
Washer
Prevents water from permeating into lockset.
Operating Instructions
11
Troubleshooting
After installing the lockset and batteries,
the door can’t be locked and three short
beeps are emitted when you press the
Programming button.
The door-handing
identification process isn’t
yet complete.
Refer to step1.
When you are in the door-handing
identifying process, you get the red light
flashing three times, and three short
beeps.
Wrong door-handing or
change of the door-handing
in the memory.
Press the R button to restore the system
to factory default setting and re-execute
door-handing identifying process
( step 1)Refer to
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
(1) The depth of the latch
bolt hole is insufficient.
(2) The latch bolt is not
aimed at the opening
of the strike.
Although the electronic deadbolt has
been functioning normally, the latch bolt
suddenly locks up, and the turnpiece
inside can’t be rotated, not even with a
key.
First, take out one battery, then press
any button on the front panel for electric
discharge, and put the battery back in.
The latch bolt will automatically
re-detect its position.
Note: If the latch gets stuck frequently,
please check and fix the alignment of
the deadbolt latch & strike plate.
(1) Dig the latch bolt hole for the strike
(2) Adjust the strike to the appropriate
position.
deeper. The minimum depth is 1 in.
(2.5 cm).
You’ve installed the lockset and batteries,
but you still get no response when you
press any button.
Batteries were installed
incorrectly.
Check to see if the battery polarities
have been reversed or if the battery is
dead.
If so, re-install or change the battery.
If not, please check to see if the cable is
properly connected.
Low battery.
Replace with new alkaline batteries.
Although you succeeded in the first
execution of the door-handing identifying
process, the latch still doesn’t work.
(i.e. You can feel the motor attempting to
run, but the latch bolt is stuck, and the
turnpiece can’t be rotated.)
The door can be locked normally, but
when you try to unlock it, you hear three
short beeps and the lock won't unlock
when you enter the user code and press
the programming button.
Unlock the door with the key and
re-program the unit.
If the problem persists, call our customer
service department.
Warranty
Delete an Existing User Code
2
Delete All User Codes at Once
3
Default programming code (PC): 0000
Default user code (UC): 1234
Your new programming code (PC) ____________
Your new user code (UC) ___________________
The same programming code and user code cannot be accepted.
The lock will cease operation if unauthorized codes are entered more than
5 times. The system will unfreeze after 45 seconds.
DO THIS FIRST
Door Handing Identification Process
The lock needs to learn if your door is a right- or left-handed.handed
0
!
Toggle Auto-Lock On/Off
5
Note:
The preset delay-time is 30 seconds. You can change the time by following the instructions
in Step 7. Repeat Step 6 to cancel the auto-locking function.
6
Set Auto-Lock Time Delay
Note: The delay time can be programmed for anywhere from 10 - 99 seconds
Toggle Mute On/Off
7
Note: Repeat Step 8 to toggle mute on and off.
LED illumination will still function when mute is toggled on.
Create a One-Time User Code 4–10 Digits Long
Enable/Disable All User Codes
Note:
The lock can only be operated by key during the time.
Repeat the steps to enable the user codes again.
Auto-locking and keypad locking functions will be invalid when user codes are disabled.
1
4
5
6
7
8
9
10
9
Note: The one-time user code will automatically expire after it is used one time.
Keep the door open while programming to avoid being locked out accidentally.
The lock contains one factory-preset user code but can be programmed to
store up to a total of six additional unique user codes.
Codes can be added and deleted at any time. For first-time programming, use factory
default programming code. It’s recommended to change the default programming code
and default user code right after you install the lock.
Operation Indicator Sounds and Lights
8
Add New User Code
1
Note: Up to 6 sets of user codes can be saved. User codes should be 4–10 digits in length.
Change Programming Code
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
4
Enter New PC.
Enter New UC.
Enter the UC
you want to
delete.
Enter
seconds
(10~99).
Enter
One Time
Code.
2
3
Note:
The lock can only be operated by key during that time.
Auto-locking and keypad locking functions will be invalid when user codes are deleted.
Enter PC.
The deadbolt latch is stuck
due to a warped door or
misaligned door.
The sensor did not sense
position.
1
1
5
5
6
6
7
7
8
8
2
2
3
3
4
4
While the door is locked, you hear the
latch bolt coming out when you press
the Programming button to lock the
door; however, three short beeps are
emitted. Conversely, while the door is
open, no beeps are emitted when
locking the latch bolt.
1
2
3
4
5
6
7
8
9
0
USER GUIDE
ELECTRONIC DEADBOLT
R
Sounds
Lights Meaning
Successful Operation
Successful Programming
Operation Error
Code Input Error; System Shuts
Down for 45 seconds
Low Battery Power
Default Setting Restored
In Programming Mode
1 Beep
2 Long Beeps
3 Beeps
5 Beeps
10 Rapid Beeps
Flashes Green Once
Flashes Green Twice
Flashes Red 3 Times
Flashes Red 5 Times
Flashes Red 10 Times
Flashes Orange 3 Times
Flashes Orange Slowly
Restore Default Settings
Press
R
Note: Press the button for more than 5 seconds; the programming
is reset back to the original factory codes once you hear 3
long beeps.
After restoring default settings, you must run the door
handing identifying process (#1) again before
programming any other functions.
R
R
Reset
button
Do not use any chemical liquid or lubricating oil with additives to clean the lock body .
It will damage the surface or even mainboard.
The manufacturer warrants the product to be free from defects in material and workmanship for a period of 12
months from the original date of purchase. If you discover a defect in the product covered by this warranty, we will
repair or replace the item at our option using new or refurbished components.
EXCLUSIONS
This warranty covers defects in manufacturing discovered while using the products as recommended by the
manufacturer rather than occurred by the act of God, and damages caused by misuse, abuse, and unauthorized
modification.
LIMITED LIABILITY
The manufacturer will not be held liable for incidental or consequential losses or damages from any act of God.
Unit Interface
Battery Lid
Slide the lid to change the batteries.
Battery Holder
Four AA (1.5 V) alkaline batteries
(not included).
R Button (Reset)
Restore default settings.
Turn-piece
To lock/unlock the lockset from inside.
Programming Button
Programming button is for entering codes,
clearing errors and setting functions.
It is also used to lock the door.
Number Buttons
To enter user codes. Each user code is
Cylinder
To lock/unlock the lockset from outside.
Washer
Prevents water from permeating into lockset.
Operating Instructions
11
Troubleshooting
After installing the lockset and batteries,
the door can’t be locked and three short
beeps are emitted when you press the
Programming button.
The door-handing
identification process isn’t
yet complete.
Refer to step1.
When you are in the door-handing
identifying process, you get the red light
flashing three times, and three short
beeps.
Wrong door-handing or
change of the door-handing
in the memory.
Press the R button to restore the system
to factory default setting and re-execute
door-handing identifying process
( step 1)Refer to
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
(1) The depth of the latch
bolt hole is insufficient.
(2) The latch bolt is not
aimed at the opening
of the strike.
Although the electronic deadbolt has
been functioning normally, the latch bolt
suddenly locks up, and the turnpiece
inside can’t be rotated, not even with a
key.
First, take out one battery, then press
any button on the front panel for electric
discharge, and put the battery back in.
The latch bolt will automatically
re-detect its position.
Note: If the latch gets stuck frequently,
please check and fix the alignment of
the deadbolt latch & strike plate.
(1) Dig the latch bolt hole for the strike
(2) Adjust the strike to the appropriate
position.
deeper. The minimum depth is 1 in.
(2.5 cm).
You’ve installed the lockset and batteries,
but you still get no response when you
press any button.
Batteries were installed
incorrectly.
Check to see if the battery polarities
have been reversed or if the battery is
dead.
If so, re-install or change the battery.
If not, please check to see if the cable is
properly connected.
Low battery.
Replace with new alkaline batteries.
Although you succeeded in the first
execution of the door-handing identifying
process, the latch still doesn’t work.
(i.e. You can feel the motor attempting to
run, but the latch bolt is stuck, and the
turnpiece can’t be rotated.)
The door can be locked normally, but
when you try to unlock it, you hear three
short beeps and the lock won't unlock
when you enter the user code and press
the programming button.
Unlock the door with the key and
re-program the unit.
If the problem persists, call our customer
service department.
Warranty
Delete an Existing User Code
2
Delete All User Codes at Once
3
Default programming code (PC): 0000
Default user code (UC): 1234
Your new programming code (PC) ____________
Your new user code (UC) ___________________
The same programming code and user code cannot be accepted.
The lock will cease operation if unauthorized codes are entered more than
5 times. The system will unfreeze after 45 seconds.
DO THIS FIRST
Door Handing Identification Process
The lock needs to learn if your door is a right- or left-handed.handed
0
!
Toggle Auto-Lock On/Off
5
Note: The preset delay-time is 30 seconds. You can change the time by following the instructions
in Step 7. Repeat Step 6 to cancel the auto-locking function.
6
Set Auto-Lock Time Delay
Note: The delay time can be programmed for anywhere from 10 - 99 seconds
Toggle Mute On/Off
7
Note: Repeat Step 8 to toggle mute on and off.
LED illumination will still function when mute is toggled on.
Create a One-Time User Code 4–10 Digits Long
Enable/Disable All User Codes
Note:
The lock can only be operated by key during the time.
Repeat the steps to enable the user codes again.
Auto-locking and keypad locking functions will be invalid when user codes are disabled.
1
4
5
6
7
8
9
10
9
Note: The one-time user code will automatically expire after it is used one time.
Keep the door open while programming to avoid being locked out accidentally.
The lock contains one factory-preset user code but can be programmed to
store up to a total of six additional unique user codes.
Codes can be added and deleted at any time. For first-time programming, use factory
default programming code. It’s recommended to change the default programming code
and default user code right after you install the lock.
Operation Indicator Sounds and Lights
8
Add New User Code
1
Note: Up to 6 sets of user codes can be saved. User codes should be 4–10 digits in length.
Change Programming Code
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
Enter PC.
4
Enter New PC.
Enter New UC.
Enter the UC
you want to
delete.
Enter
seconds
(10~99).
Enter
One Time
Code.
2
3
Note:
The lock can only be operated by key during that time.
Auto-locking and keypad locking functions will be invalid when user codes are deleted.
Enter PC.
The deadbolt latch is stuck
due to a warped door or
misaligned door.
The sensor did not sense
position.
1
1
5
5
6
6
7
7
8
8
2
2
3
3
4
4
While the door is locked, you hear the
latch bolt coming out when you press
the Programming button to lock the
door; however, three short beeps are
emitted. Conversely, while the door is
open, no beeps are emitted when
locking the latch bolt.
WARRANTY
The retailer of this product hereby warrants, subject to the conditions set forth below, that it will either repair or replace, at its
option, this product if it proves to be defective by reason of improper workmanship or materials within the original purchaser’s
limited time. In order to obtain repairs or replacement under this limited warranty you must bring this product to the retailer’s
store in which you bought it. Original purchaser: This limited warranty is limited to the original purchaser at retail of this product
from retailer. Limited 25 years mechanical and 1 year electronic warranty. Except to the extent prohibited by applicable law, no
other warranties, whether express or implied, including the warranties of merchantability and tness for a particular purpose,
shall apply to this product. Under no circumstances shall retailer be liable for consequential or incidental damages in connection
with this product. To the extent retailer is prohibited by applicable law from excluding implied warranties, the duration of such
implied warranties which are not excludable shall be the original purchaser’s limited warranty time. Some states do not allow
the limitation on how long an implied warranty lasts, so the above limitation on the duration of implied warranties which are
not excludable, if any, may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion of incidental or consequential damages may not apply to you. Retailer neither
assumes nor authorizes any representative or other person to assume for it any obligation or liability other than such as
is expressly set forth herein. This limited warranty gives you specic legal rights, and you may also have other rights which
vary from state to state. For warranty service, please call 1-877-442-8347, 8:00 a.m. - 8:00 p.m., EST, Monday - Friday.
66482 / 02
FEDERAL COMMUNICATIONS COMMISSION STATEMENT
This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation. Changes or modications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
SAFETY INFORMATION
Read the precautions and instructions in this manual before installing
and using this lock. Save this manual for future reference.
WARNING: Do not use an electric screwdriver during installation.
CAUTION : Please use four alkaline batteries (not included) for the best performance.
A. Do not attempt to disassemble any internal components of
the lockset. Doing so will void the limited warranty.
B. Do not drop or hit the lockset. Too much shock may result in permanent damage.
C. Do not use pins or sharp objects to press the keypad.
D. Always create a backup of information you wish to
keep (Programming Code, user code, etc.).
E. Promptly change the Programming Code before operating this lockset.
Item #0817538
ELECTRONIC KEYPAD DEADBOLT
Model #G2X2D01
Questions
Call customer service at 1-877-442-8347,
8:00 a.m. - 8:00 p.m., EST, Monday - Friday.
Questions/¿Preguntas?
ATTACH YOUR RECEIPT HERE
Serial Number
Purchase Date
CARE AND MAINTENANCE
THE FOLLOWING CARE INSTRUCTIONS SHOULD BE FOLLOWED TO ENSURE A
LONG LASTING FINISH:
1. Remove locks, or do not install locks, prior to painting your door.
2. Do not use any chemical liquid or lubricating oils with additives to clean the lock.
WARNING: The Manufacturer advises that no lock can provide complete security
by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualied locksmith or other security professional.
Printed in Taiwan