Installation Guide

ManualsBrandsGatehouse ManualsElectronic Entry Door DeadboltsGCX2D01

PROGRAMMING

OVERVIEW OF FUNCTIONS

PROGRAMMING

HOW TO LOCK / UNLOCK

MASTER CODE (6 digits)

After changing your Master Code, do not pass your Master Code to anyone else.

WRITE YOUR MASTER CODE HERE FOR EASY ACCESS



KEYPAD

Unlock the lockset with a valid key.



KEY OVERRIDE

Yellow light ashes when the

batteries are low in power.



INTERIOR INDICATOR LIGHT

Lock or unlock the lockset

manually.



INTERIOR THUMBTURN

Scan for

Programming

https://goo.gl/ENGLFG

To unlock

Enter valid User Code or

Master Code.



RESTORE TO FACTORY SETTINGS



HOW TO PROGRAM THE LOCKSET BY FUNCTION CODES (Programming Mode)

Press and hold SET button while inserting the

battery back. Hold the set button until a long

beep is heard followed by a short beep.

Enter the default Master Code (123456)

to complete the bolt direction setting.

Remove one battery

SET



SET BUTTON

SET

SETSET

To lock

Use a valid key to lock.

Use a valid key to unlock.

This will erase all stored information, including bolt direction.

The preset Master code is 123456.

Alarm sounds for 10 seconds and unit deactivates for 1 minute after 4 consecutive incorrect code access attempts.

ACCESS CODE LIST

WARRANTY

The retailer of this product hereby warrants, subject to the conditions set forth below, that it will either repair or replace, at its option, this product if it proves

to be defective by reason of improper workmanship or materials within the original purchaser's limited time. In order to obtain repairs or replacement under

this limited warranty you must bring this product to the retailer's store in which you bought it.

Original purchaser: This limited warranty is limited to the original purchaser at retail of this product from retailer. Limited 25 years mechanical and 1 year

electronic warranty.

Except to the extent prohibited by applicable law, no other warranties, whether express or implied, including the warranties of merchantability and tness for

a particular purpose, shall apply to this product. Under no circumstances shall retailer be liable for consequential or incidental damages in connection with

this product. To the extent retailer is prohibited by applicable law from excluding implied warranties, the duration of such implied warranties which are not

excludable shall be the original purchaser's limited warranty time. Some states do not allow the limitation on how long an implied warranty lasts, so the

above limitation on the duration of implied warranties which are not excludable, if any, may not apply to you. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion of incidental or consequential damages may not apply to you.

Retailer neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than such as is expressly set forth

herein. This limited warranty gives you specic legal rights, and you may also have other rights which vary from state to state.

For warranty service, please call 1-877-4GATEHS, 8:00 a.m. - 8:00 p.m., EST, Monday - Friday.

FEDERAL COMMUNICATIONS COMMISSION STATEMENT

This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Name User Code (4-6 digits)

SETSET

→



ENTER / LOCK BUTTON

Exterior indicator light:

1. Green light indicates the user code entered is a

valid code.

2. Red light indicates the user code entered is an

invalid code or the unit is in programming mode.

3. Yellow light ashes when the batteries are low

in power.

Press button

TROUBLESHOOTING

INSTALLATION



OPERATION



ANSWERSQUESTIONS

A. The latch does not operate

correctly after installation.

B. Feel bump while turning

the thumbturn or the key?

1. The batteries may be low in power. Replace with four new batteries for best performance.

(Alkaline batteries only)

ANSWERSQUESTIONS

A. Battery indicator keeps

ashing.

ANSWERSQUESTIONS

B. Keypad not responding.

C. Master Code cannot be

changed.

D. What should I do if wrong

code was entered?

E. Cannot delete all

User Codes.

1. Make sure the whole code entering process is completed within 10 seconds, otherwise the unit will time out.

2. Make sure the Master Code has been entered correctly.

F. Cannot add a new

User Code.

G. "Auto Lock" does not

function.

H. Lockset is not able

to unlock / lock by keypad.

I. Lockset is unable to reset.

J. How to operate the

lockset in darkness?

If the lock appears to be damaged or does not operate properly,

please contact customer service at 1-877-442-8347, 8 a.m - 8 p.m., EST, Monday - Friday.

K. The red indicator is still on

after setting is completed.

M. I cannot remove my key

unless it is in the locked

position.

1. Make sure the backset on the latch is set to the proper length.

2. Make sure prior to installation that the latch bolt is retracted and key is not in lockset when installing the deadbolt.

3. Please restore to factory setting and enter the default Master Code to set up the lock.

1. Please execute lock & unlock function to allow the motor to reposition itself again.

2. Please restore to factory setting and enter the default Master Code to set up the lock.

C. Fail to set up the lock.

1. Please make sure the lock is installed correctly.

2. Please install fresh batteries and make sure the cable is connected correctly.

1. Check to make sure the batteries are installed properly.

2. The batteries are getting low if the battery indicator keeps ashing. Replace batteries for best performance

(Alkaline batteries only).

3. Make sure the cable is well-connected to the port and was not damaged during installation.

4. Please make sure the lock has been set up and complete the bolt direction determination.

1. Make sure you have entered the correct User Code.

2. The battery is low if the battery indicator light keeps ashing. Please replace with four new batteries.

3. Make sure the cable is rmly connected.

4. Check the cable for any damage that may have occurred during installation.

5. Make sure the batteries are properly installed. (Alkaline batteries only)

6. Check the strike plate to make sure it is properly aligned and clear so the bolt can freely move in the hole.

1. Press any button to activate the lockset back light.

1. Check if [SET] button is jammed.

2. Re-install the batteries.

1. Please refer to the instructions given above to restore factory settings and reprogram all codes.

2. The battery is low if the battery indicator light keeps ashing. Please replace with four new batteries.

1. Make sure the whole code entering process is completed within 10 seconds, otherwise the unit will time out.

2. Make sure the Master Code has been entered correctly.

3. The new User Code will not be accepted when the capacity is full. Try to delete some existing User Codes

and then add new one(s) again. A User Code must be at least 4 to 6 digits.

1. The batteries are low on power if the battery indicator keeps ashing. Please replace with four new batteries for

best performance. (Alkaline Batteries Only).

2. Please refer to the instructions given above to enable the Auto-Lock function.

1. Un-install the interior and exterior assemblies.

Before re-installation, please follow these guidelines:

1) Make sure the bolt is in the retracted position.

2) Do not have any key in the cylinder during installation.

3) Make sure the torque blade is inserted horizontally.

2. Reset the unit to factory settings and reprogram the Master Code and user codes.

1. Un-install the interior and exterior assemblies.

Before re-installation, please follow these guidelines:

1) Make sure the bolt is in the retracted position.

2) Do not have any key in lock cylinder.

3) Make sure the torque blade is inserted horizontally.

1. Please refer to the instructions given above to restore factory settings and reprogram all codes.

L. The lockset locks when I

enter my code and unlocks

when I press the .

1. Press button once and continue to input code according to regular procedures.

・A Master Code can be used to program or unlock the lockset.

・The preset Master Code is 123456.

・Please change the Master Code before operating the lock.

Change the existing

Master Code

Enter New Master Code (6 digits)

Add user code(s)

・The unit can store up to 10 customized User Codes (4-6 digits long).

Enter New User Code (4-6 digits)

Enter unwanted User Code (4-6 digits)

Delete individual user or

single-entry code(s)

Delete all user /

single-entry codes

・Delete one or more codes at a time, including User Codes or Single-

entry Codes.

・Users/Single-entry codes cannot be retrieved after they are deleted.

・Delete ALL User Codes at once.

・Use the existing Master Code (6 digits) to unlock the unit after the

deletion of User/Single-entry Codes.

Delete another code

Add another code

BASIC

SETTINGS

Press and hold the [SET] button until the

unit beeps, then release the [SET] button

Press and hold the [SET] button until the

unit beeps, then release the [SET] button

Press and hold the [SET] button until the

unit beeps, then release the [SET] button

Press and hold the [SET] button until the

unit beeps, then release the [SET] button

Press

Enter current Master Code

(6 digits) then press

Enter current Master Code

(6 digits) then press

Enter current Master Code

(6 digits) then press

Enter current Master Code

(6 digits) then press

・The single-entry user code can be used for only one successful entry

and will be invalid when the lockset is locked again.

・The unit can store up to 5 single-entry user codes (4 digits long).

Add single-entry code(s)

Enter New Single-entry Code (4 digits)

Vacation mode

・Disabled by default.

・All User / Single-entry Codes (if any) will be temporarily disabled

when Vacation Mode is enabled. Only the existing Master Code can

unlock the unit.

・The existing User / Single-entry Codes will be re-activated once the

Vacation Mode is turned off.

Volume Control

・The beeper can be turned off if desired. Beeps will still sound during

programming.

Auto-lock function

・Disabled by default.

・When enabled, the lock will automatically re-lock after unlocking

(Default: 10 seconds).

Auto-lock delay timer

Enter new digits (10 - 99 seconds)

・Auto-lock timer can be set from 10 to 99 seconds according to your

demand.

Add another code

ADVANCED

SETTINGS

Press and hold the [SET] button until the

unit beeps, then release the [SET] button

Press and hold the [SET] button until the

unit beeps, then release the [SET] button

Press and hold the [SET] button until the

unit beeps, then release the [SET] button

Press and hold the [SET] button until the

unit beeps, then release the [SET] button

Press and hold the [SET] button until the

unit beeps, then release the [SET] button

Press

Enter current Master Code

(6 digits) then press

Enter current Master Code

(6 digits) then press

Enter current Master Code

(6 digits) then press

Enter current Master Code

(6 digits) then press

Enter current Master Code

(6 digits) then press

Turn On.

＋

Turn Off.

＋

Turn On.

＋

Turn Off.

＋

Turn On.

＋

Turn Off.

＋

・Programming Mode will automatically time out after 10 seconds of inactivity.

・If you make a mistake during programming, press the interior SET BUTTON (as shown in above diagram) to leave Programming Mode and start over.

AB16206 Printed in Taiwan