User's Manual
Table Of Contents
- Section 1 Introduction
- 1.1 Purpose of This Manual
- 1.2 General Description
- 1.3 General Specifications
- Section 2 Installation / Initial Turn-On
- 2.1 Introduction
- 2.2 Installation Checkboxes
- 2.3 Transmitter Cabinet Placement
- 2.4 Transmitter AC Connection
- 2.5 Signal and Ground Connections
- 2.6 Interlock Connections
- 2.7 3 Port Patch Panel
- 2.8 Motorized RF Switch Connections
- 2.9 Install PA and PS Modules
- 2.10 Initial Turn-On
- 2.11 Parallel Remote Control Connections
- 2.12 Remote Status Outputs, J15 & J16
- Section 3 Operation/ Adjustments
- 3.1 Introduction
- 3.2 Transmitter Control Panel
- 3.3 Graphical User Interface (GUI)
- 3.4 GUI Home Page
- 3.5 Drive Chain Main Menu
- 3.6 Power Amp Main Menu
- 3.7 Output Main Menu
- 3.8 Power Supply Main Menu
- 3.9 System Main Menu
- 3.10 GUI Menu Structures
- Section 4 Theory of Operation
- 4.1 Introduction
- 4.2 Block Diagram Descriptions
- 4.3 Transmitter Control System
- 4.4 Transmitter RF System
- 4.5 Power Supplies
- Section 5 Replacement Procedures
- 5.1 Introduction
- 5.2 PA Module Removal
- 5.3 PA Module Pallet Replacement
- 5.4 Power Supply Module Replacement
- 5.5 Circulator Removal/Replacement
- 5.6 Blower Assembly Removal
- Section 6 ISP (In-System Programming)
- 6.1 Introduction
- 6.2 Installing the ISP Program
- 6.3 ISP Procedures
- Section 7 Parts List
- 7.1 Parts List Index
10/19/07 888-2687-001 2-17
WARNING: Disconnect primary power prior to servicing.
Section 2 Installation / Initial Turn-On
Ranger ™ Mobile Series
• J13 and J14 - Remote Transmitter Control Functions
• J15 and J16 - Remote Status Outputs
• J17 - Remote Analog Metering Outputs
NOTE:
The forward slash ( / ) in front of a signal name means active low. The signal /
INPUT 1 for example is activated by momentarily bringing that input low. Signal
names without the forward slash are considered active high. This convention is
used throughout the schematics.
Figure 2-10 External I/O Connector Locator
2.11.1 Transmitter Control Functions, J13 and J14
All control inputs use opto-isolators for surge protection. The opto-isolators are
powered by an internal +5Vdc from an isolation protection circuit, U54. All transmitter
GND A
/INPUT 1
/INPUT 2
/INPUT 3
/INPUT 4
GND
GND
/INPUT 5*
/INPUT 6*
/INPUT 7
/INPUT 8*
GND
GND
INPUT 9
/INPUT 10
/INPUT 11
/INPUT 12*
GND
GND
/INPUT 13*
/INPUT 14*
/INPUT 15*
/INPUT 16*
GND
GND B
+5VDC ISOLATED
OUTPUT 1
OUTPUT 2
OUTPUT 3
OUTPUT 4
OUTPUT 5
OUTPUT 6
OUTPUT 7
OUTPUT 8
+VDC EXT SUPPLY
GND
GND B
+5VDC ISOLATED
OUTPUT 9
OUTPUT 10
OUTPUT 11
OUTPUT 12
OUTPUT 13
OUTPUT 14
OUTPUT 15
OUTPUT 16
+VDC EXT SUPPLY
GND
GND A
VOUTA
VOUT B
VOUT C
VOUT D
GND
GND
VOUT E
VOUT F
VOUT G
VOUT H
GND
SYSTEM
FAULT OFF
INTERLOCK
RF SWITCH
INTERLOCK
(MUTE)
11
1
12
12
12
12
1
1
12
12
1
1
12
12
1
NOT USED FOR RANGER
J11
J12
J15
J16
J13
J14
J17
J18
1-2
3-4
5-6
7-8
9-10
11-12
EXTERNAL I/O BOARD
REMOTE CONNECTOR
LOCATIONS AND PINOUTS
NOTE:
Left half of PC
Board not shown
* Not Used