User's Manual

ManualsBrandsGatesAir ManualsElectronicsRanger CZ725F

1

2

3

4

5

6

7

8

9

Table Of Contents

Section 1 Introduction
1.1 Purpose of This Manual
1.2 General Description
- 1.2.1 System Block Diagrams
- 1.2.2 Transmitter Control System
- 1.2.3 PA Module
- 1.2.4 Power Supplies
- 1.2.5 Apex™ Exciter
1.3 General Specifications
Section 2 Installation / Initial Turn-On
2.1 Introduction
- 2.1.1 Installation Drawings
2.2 Installation Checkboxes
2.3 Transmitter Cabinet Placement
2.4 Transmitter AC Connection
2.5 Signal and Ground Connections
2.6 Interlock Connections
- 2.6.1 External Interlocks
- 2.6.2 RF Mute Interlock
2.7 3 Port Patch Panel
2.8 Motorized RF Switch Connections
2.9 Install PA and PS Modules
2.10 Initial Turn-On
- 2.10.1 RF Initial Turn ON
2.11 Parallel Remote Control Connections
- 2.11.1 Transmitter Control Functions, J13 and J14
2.12 Remote Status Outputs, J15 & J16
- 2.12.1 Remote Power Metering, J17
Section 3 Operation/ Adjustments
3.1 Introduction
3.2 Transmitter Control Panel
- 3.2.1 Main Menu “Hardware” Buttons
3.3 Graphical User Interface (GUI)
- 3.3.1 Global Status and Navigation
3.4 GUI Home Page
3.5 Drive Chain Main Menu
- 3.5.1 Drive Service
- 3.5.2 Drive Meter Calibration
3.6 Power Amp Main Menu
- 3.6.1 PA Faults
  - 3.6.1.1 Module 3 strike Routine
- 3.6.2 PA Meters
- 3.6.3 PA Data
- 3.6.4 PA Service
  - 3.6.4.1 PA Setup (Gain Balance)
3.7 Output Main Menu
- 3.7.1 Output Service
- 3.7.2 Module Phasing Procedure
  - 3.7.2.1 Output Setup
- 3.7.3 Forward and Reflected Power Calibrations
3.8 Power Supply Main Menu
- 3.8.1 PS Service
  - 3.8.1.1 AC Mains Meter Calibration
3.9 System Main Menu
- 3.9.1 Control System
- 3.9.2 System Log
- 3.9.3 System Service
  - 3.9.3.1 System Setup
  - 3.9.3.2 Software Revisions (SW REVs)
    - 3.9.3.2.1 Hardware Revisions
3.10 GUI Menu Structures
Section 4 Theory of Operation
4.1 Introduction
4.2 Block Diagram Descriptions
4.3 Transmitter Control System
- 4.3.1 Active Logic Symbols
- 4.3.2 Micro Module
- 4.3.3 CPLD, Complex Programmable Logic Device
  - 4.3.3.1 I/O Expansion
  - 4.3.3.2 Life Support Backup
- 4.3.4 Controller Area Network (CAN) Bus
- 4.3.5 System Control Bus
- 4.3.6 Main Controller
- 4.3.7 External I/O Board
  - 4.3.7.1 External Interlocks
  - 4.3.7.2 RF Mute Interlock
4.4 Transmitter RF System
- 4.4.1 CZ500F RF System Description
- 4.4.2 CZ1000F RF System Description
- 4.4.3 ApexR Exciter
- 4.4.4 Backplane Interface Board
  - 4.4.4.1 Control Distribution
  - 4.4.4.2 Low Voltage Power Supply Distribution
- 4.4.5 PA Module
- 4.4.6 PA Module Circulators
- 4.4.7 PA Module Combiner (CZ1000F only)
  - 4.4.7.1 Combiner Isolation Load (CZ1000F only)
- 4.4.8 RF Monitor Board
4.5 Power Supplies
- 4.5.1 AC Input
- 4.5.2 PA Power Supply Module
- 4.5.3 Low Voltage Power Supply (LVPS)
- 4.5.4 Power Supply Monitor Board
Section 5 Replacement Procedures
5.1 Introduction
5.2 PA Module Removal
- 5.2.1 CZ1000F PA Module Air Block
5.3 PA Module Pallet Replacement
5.4 Power Supply Module Replacement
5.5 Circulator Removal/Replacement
5.6 Blower Assembly Removal
Section 6 ISP (In-System Programming)
6.1 Introduction
6.2 Installing the ISP Program
6.3 ISP Procedures
- 6.3.1 Control System ISP Procedure
- 6.3.2 PA Module ISP Procedure
- 6.3.3 ISP Errors
Section 7 Parts List
7.1 Parts List Index

10/19/07 888-2687-001

WARNING: Disconnect primary power prior to servicing.

1
...
2
3
4
5
6
7
...
...
156

Who We Are: About Us; Company; Careers; Terms & Privacy

Resources: List of Manufacturers; Support; For the Press; Media assets; FAQ

Get in touch: Blog; Email; DMCA

ManualShelf © 2013-2024