Your Gateway Computer componentguide FPD 1540 Monitor Operating Maintaining
www.gateway.
Contents Using Your FPD 1540 Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Connecting the monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Starting the monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Adjusting monitor settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 External controls . . . . . . . .
ii
Using Your FPD 1540 Monitor The FPD 1540 monitor is a high-resolution color LCD with: ■ Over 16 million colors ■ Excellent contrast and legibility ■ Space-saving and lightweight design ■ Reduced power usage 1
Using Your FPD 1540 Monitor Connecting the monitor To connect the monitor: 2 1 Position your computer and the monitor so you can easily reach the back panel of each. 2 3 Make sure that your computer is turned off. 4 Lay the monitor face down. Avoid the scratching the screen by placing it on a towel or other non-abrasive surface. Remove the cable cover on the back of the monitor. www.gateway.
Connecting the monitor 5 Connect one end of the video cable to the video port on the back of the monitor. 6 Connect the power cord to the power connector on the back of the monitor. www.gateway.
Using Your FPD 1540 Monitor 4 7 Connect the other end of the video cable to the video port on the back of your computer. 8 Plug the other end of the power cord into a grounded electrical outlet. www.gateway.
Connecting the monitor 9 Thread the video cable and the power cord through the cable cover slot, then replace the cover. www.gateway.
Using Your FPD 1540 Monitor Starting the monitor To start the monitor: 1 Press the power button on the front of the monitor. Power Button 2 6 Turn on your computer. www.gateway.
Starting the monitor 3 After your computer is running, the power LED on the monitor should be green. Power LED Allow about 10 seconds for the display image to appear. If the power LED is not green or you do not see a display image, check the connections. For more troubleshooting information, see “Troubleshooting” on page 21. 4 5 Adjust the tilt of the monitor for the best viewing angle. Use the on-screen display (OSD) to adjust other monitor settings.
Using Your FPD 1540 Monitor Adjusting monitor settings Use the external controls (located on the monitor itself) and software controls (accessible in Windows) to adjust the display image. For more information about software controls, see “Software controls” on page 14. External controls This monitor features an on-screen display (OSD) that lets you adjust and save contrast, brightness, and other settings. The monitor saves changes you make to the settings, even if you turn off the monitor.
Adjusting monitor settings Monitor buttons ■ Arrows OSD active: Press to select OSD menus or controls. OSD inactive: If the Hot Key option on the Tools menu is off, press to open the OSD. If the Hot Key option on the Tools menu is on, press to adjust brightness. ■ +– OSD active: Press to adjust an OSD control. OSD inactive: If the Hot Key option on the Tools menu is off, press to open the OSD. If the Hot Key option on the Tools menu is on, press to adjust the contrast.
Using Your FPD 1540 Monitor OSD menus You can access any of these menus in the OSD: OSD Menu Description Brightness/Contrast Controls Brightness Adjusts the brightness of the display image. Use the lowest brightness setting you are comfortable with to maximize the life of the monitor backlights. COLOR You may need to readjust brightness after the monitor has warmed up. FH : 48.3 kHz NEG. FV : 60.0 Hz NEG. Contrast Adjust the contrast of the display image.
Adjusting monitor settings OSD Menu Description Image Controls Horizontal image position Adjusts the horizontal position of the display image. COLOR Vertical image position Adjusts the vertical position of the display image. FH : 48.3 kHz NEG. FV : 60.0 Hz NEG. Horizontal image size Adjusts the horizontal size of the display image. Fine-tune image Adjusts the focus, clarity, and image stability. Color Control Systems Color Control Systems Select one of six preset color settings.
Using Your FPD 1540 Monitor OSD Menu Description Tools Language Changes the language on the OSD menus. COLOR AA OSD Position z Manually adjusts the position of the OSD on the screen. FH : 48.3 kHz NEG. FV : 60.0 Hz NEG. OSD Turn Off The OSD automatically closes when it is not being used. Use this control to select the number of seconds the OSD waits before it closes. You can select 10, 20, 30, 45, 60, or 120 seconds. OSD Lock Out Prevents access to the OSD.
Adjusting monitor settings OSD Menu Description Tools (continued) Off Timer The monitor turns off automatically when the computer is not being used. If you do not want the monitor to turn off automatically, turn this timer off. Factory Preset Use this control to activate the Reset button. To reset all settings to the factory default, press and hold the Reset button for several seconds. To reset an individual control, select a control, then press and hold the Reset button for several seconds.
Using Your FPD 1540 Monitor Software controls Adjusting the color depth and screen resolution are two of the most basic monitor settings you may need to change. Adjusting the color depth Color depth is the number of colors your video card uses. Most images look best displayed with the maximum number of colors available. Windows lets you choose from several color depth settings for the monitor. We recommend that you use the 32-bit True Color setting or the highest setting available at all times.
Adjusting monitor settings 3 Click the Settings tab. 4 Click the arrow button to open the Color quality or Colors list, then click the color depth you want. 5 To save your changes in Windows XP, click OK, then click Yes. - OR To save your changes in Windows 2000, click OK, then click OK again. Help and Support For more information about adjusting monitor settings in Windows XP, click Start, then click Help and Support.
Using Your FPD 1540 Monitor Adjusting the screen resolution You can change the screen resolution. For example, you can increase the resolution to fit more icons on your desktop, or you can decrease the resolution to make reading and identifying objects on the monitor easier. The higher the resolution, the smaller individual components of the screen (such as icons and menu bars) appear. To change the screen resolution: 1 In Windows XP, click Start, then click Control Panel.
Adjusting monitor settings 4 5 Drag the Screen resolution or Screen area slider to the resolution you prefer. To save your changes in Windows XP, click OK, then click Yes. - OR To save your changes in Windows 2000, click OK, then click OK again. Help and Support For more information about adjusting screen resolution in Windows XP, click Start, then click Help and Support. Type the keyword changing screen resolution in the HelpSpot Search box , then click the arrow. www.gateway.
Using Your FPD 1540 Monitor Video modes The monitor supports several video modes. The best screen resolution is: ■ 1024 × 768 The supported video modes are: Screen Resolution (display mode) Horizontal Frequency Vertical Frequency 640 × 480 31.5 kHz to 37.5 kHz 60 Hz to 75 Hz 800 × 600 37.9 kHz to 46.9 kHz 75 Hz to 60 Hz 1024 × 768 48.
Power management Power management ENERGY STAR As an ENERGY STAR® Partner, Gateway has determined that this product meets the ENERGY STAR guidelines for energy efficiency. This monitor complies with the EPA's International ENERGY STAR Program, which is a program designed to encourage manufacturers of computer equipment to build circuitry into their products to reduce energy consumption during time of non-use.
Using Your FPD 1540 Monitor Maintenance To keep the monitor in optimal working order: ■ Do not block the ventilation holes. ■ Do not expose the monitor to rain or use near water. ■ Keep the monitor away from radiators or heat vents. ■ Keep the monitor out of direct sunlight. To clean the monitor, use a soft cloth lightly moistened with water only. Wipe the cabinet, screen, and controls. Warning 20 Do not use any type of abrasive pad or glass cleaner. You will permanently scratch the screen.
Troubleshooting Troubleshooting If you have problems with the monitor, the information in this troubleshooting section may help you solve them. Important Make sure that the monitor has warmed up for approximately 30 minutes before making any judgments about the picture quality. No power ■ Make sure that the power cord is connected correctly to both the back of the monitor and the wall outlet. For more information about connecting the power cord, see “Connecting the monitor” on page 2.
Using Your FPD 1540 Monitor No picture ■ Make sure that the power cord is connected correctly to both the back of the monitor and the wall outlet. For more information about connecting the power cord, see “Connecting the monitor” on page 2. ■ Make sure that the video cable is connected securely to the back of the monitor and your computer. For more information about connecting the video cable, see “Connecting the monitor” on page 2.
Troubleshooting Image “ghosts” ■ If a “ghost” of an image remains on the monitor screen, turn off the monitor for the length of time that the image was displayed on the screen. For example, if the image was displayed for one hour, turn off the monitor for one hour. ■ To avoid ghost images, use a screen saver. Display colors are wrong ■ Use the OSD controls to select a preset color setting or to adjust the colors manually. For more information, see “OSD controls” on page 9.
Using Your FPD 1540 Monitor Color is not uniform ■ Turn on the FACTORY PRESET control in the OSD, then press the RESET button for several seconds to return the monitor settings to the ideal settings. For more information, see “OSD controls” on page 9. Image is not sized or centered correctly ■ Use the OSD controls to adjust the position of the display image. For more information, see “OSD controls” on page 9.
Specifications Specifications Specifications are subject to change without notice or obligation. Monitor 15-inch active-matrix TFT (Thin Film Transistor) LCD Best screen resolution 1024 × 768 Active display area Horizontal: 12.0 in. (304 mm) Vertical: 9.0 in. (228 mm) Display colors Over 16 million colors Input signal Video: ANALOG 0.7 P-P/75 Ohms Sync: Separate sync TTL Level Horizontal sync: Positive/Negative Vertical sync: Positive/Negative Synchronization Range Horizontal: 31.5 kHz to 60.
Using Your FPD 1540 Monitor Environmental specifications Specifications are subject to change without notice or obligation. Operating temperature 41°F to 95°F (5°C to 35°C) Humidity: 30% to 80% Altitude: 0 to 10,000 ft Storage Temperature 14°F to 140°F (-10°C to 60°C) Humidity: 10% to 85% Altitude: 0 to 40,000 ft Many products for Gateway and its subsidiaries are custom engineered by our suppliers to Gateway specifications and may vary from similarly marketed products. 26 www.gateway.
Safety, Regulatory, and Legal Information Important safety information Your Gateway system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed. Warning Always follow these instructions to help guard against personal injury and damage to your Gateway system.
Safety, Regulatory, and Legal Information Setting up your system 28 ■ Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. ■ Do not use this product near water or a heat source such as a radiator. ■ Set up the system on a stable work surface. ■ The product should only be operated from the type of power source indicated on the rating label.
Important safety information Care during use ■ Do not walk on the power cord or allow anything to rest on it. ■ Do not spill anything on the system. The best way to avoid spills is to avoid eating and drinking near your system. ■ Do not expose the monitor to rain or use near water. If the monitor does get exposed to moisture, unplug it and allow it to dry for 24 hours. Call Gateway Technical Support for advice on whether the monitor is safe to turn back on.
Safety, Regulatory, and Legal Information Regulatory compliance statements United States of America Federal Communications Commission (FCC) Unintentional emitter per FCC Part 15 This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Regulatory compliance statements Canada Industry Canada (IC) Unintentional emitter per ICES-003 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par Industrie Canada.
Safety, Regulatory, and Legal Information Notices Copyright © 2003 Gateway, Inc. All Rights Reserved 14303 Gateway Place Poway, CA 92064 USA All Rights Reserved This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or transmitted by any means or in any form, without prior consent in writing from Gateway. The information in this manual has been carefully checked and is believed to be accurate. However, changes are made periodically.
www.gateway.
MAN MON NEC 15" LCD GDE R0 4/03
