customerservice@gazebopenguin.com 43224 12’x14’ GAZEBO ASSEMBLY INSTRUCTIONS DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS Assembly with more than one person recommended Tools required (not provided): 6ft (1.8m) stepladder, Robinson #2 Screwdriver, mallet, safety gloves & glasses, tarp or protective material for placing parts on during assembly, tape measure, 1'X2"X4" wood.
Before you assemble the Gazebo Please don't destroy boxes until completely assembled. Please verify the content of each box against the list of parts. It is important that this gazebo be anchored on a solid base with the provided screws. Otherwise, please ensure that you use anchors sufficient for your surface. The gazebo should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the gazebo and cause it to collapse.
Step 3: Have someone lift the beam assembly and attach each leg “G” into a corner, securing each using 4 bolts “Pp”. Repeat until all four legs are in place. Step 4: Install middle joint cover “J” at each of the 4 beam junctions, using 4 screws “Qq” each. Install corner cover “I” at each of the corners, using 4 screws “Qq” each. 2 ZZZ-204.43224.1207-18.GP.EN.
Step 5: Attach mounting brackets “O” to rafters “M”, and mounting brackets “P” to rafters “N” and “N-2”. Use threaded hole about 8” from end of rafter. Lift central hub “L” to a height of about 110” (2.79m) at the center of the gazebo. (Caution: this part may be heavy, use support as needed) Attach one end of rafter “M” to the hub using 1 bolt “Pp”. Attach other end with mounting bracket to the corner of the beam assembly with 2 bolts “Pp”. Use the set of holes closest to the inside.
Step 7: Install the flashings “Q”, “R”, “S”, and “S-2” onto the beam assembly, using screws “Qq” on the inside. The notched end of a flashing will always go in a corner of the gazebo. Step 8: Install the curtain rails “T” and “U” on the inside of the beam assembly using bolts “Pp”. Pp 4 ZZZ-204.43224.1207-18.GP.EN.
Step 9: Slide the indicated polycarbonate panels into the spaces between the rafters, using the top groove of each rafter. Ensure the side meant to face the sun is on the outside. Use a rubber hammer to carefully tap each panel into the grooves. Step 10: Insert the middle roof joints in between the rafters and slide them up under the polycarbonate panels. Tap lightly to ensure the panel is fully in the slot. Seen from above, most of the joint as well as the drain holes should be beneath the roof panels.
Step 11: Slide the remaining polycarbonate roof panels in the lower groove of the rafters and into the lower slot of the roof joints. Tap to make sure panels fit securely and do not extend past the ends of the rafters. Step 12: Starting from any end, install all edgings, with end caps “Gg” or “Hh” at each junction or corner respectively. Use bolts “Pp” to secure. 6 ZZZ-204.43224.1207-18.GP.EN.
Step 13: Install the upper crossbars on the interior of the roof using bolts “Pp”, following the shaped ends and letters. Do not tighten bolts immediately; install loose and tighten once all crossbars are in place. Repeat this step with the lower crossbars. Pp Pp Pp Step 14: a) Secure each foot plate into the ground using screws “Rr” and washers “Tt”. b) Use lag shields (Ss) if needed for harder surfaces. 7 ZZZ-204.43224.1207-18.GP.EN.
Step 15: Install the screen curtains “Ww” in the interior groove of the curtain rails, using the provided hooks. Install the privacy curtains “Xx” in the exterior groove of the rails. Once the hooks are in, use curtain rail caps “Uu” to close ends of curtain rails. IMPORTANT NOTES: Make sure all screws and bolts are tight. If conditions are windy, you may have to add cable guides at the corners. 8 ZZZ-204.43224.1207-18.GP.EN.
3 2 3 2 B CENTRAL HUB L (11-731-22) 92 5/8” ROOF RAFTER 3 2 3 2 (11-628-22) CORNER PLATE E 3 4 (11-629-22) CENTER PLATE F 3 4 ROOF RAFTER N-2 RAFTER M MOUNTING BRACKET O RAFTER N MOUNTING BRACKET P (11-638-22) 3 4 (11-663-22) 78 ¼” TOP RIGHT BEAM D LEG G (11-631-22) FOOT PLATE H (11-632-22) CORNER COVER I (11-633-22) MIDDLE COVER J 4 2 6 2 2 2 4 2 8 2 4 2 4 2 2 2 2 60 3/8” (11-630-22) 81 ½” 2 73 ¾” ROOF RAFTER N (11-637-22) TOP LEFT BEAM C 1 M (11-708-22) (11-6
TOP CAP K 2 1 2 4 (11-674-22) 1 2 31”x38” LEFT LOWER PANEL, 12’ SIDE Bb (11-721-22) LEFT LOWER PANEL, 14’ SIDE Bb-2 (11-679-22) 1 2 RIGHT LOWER PANEL, 12’ SIDE Cc (11-722-22) (11-734-22) 39”x57 ½” 37”x25 ½” RIGHT LOWER PANEL, 14’ SIDE Cc-2 (11-680-22) 1 4 1 2 (11-675-22) 37 ½”x30 ½” RIGHT UPPER PANEL, 14’ SIDE X QTY 2 1 2 1 2 1 2 LEFT EDGING, 12’ SIDE Dd (11-715-22) 2 2 2 2 2 4 72 5/8” 37 ½”x30 ½” 1 2 2 2 (11-676-22) 38 ½” LEFT MID ROOF JOINT, 12’ SIDE Y 1 72 5/8
PART (11-713-22) (11-653-22) 38 ½” 58 7/8” RIGHT MID ROOF JOINT 12’ SIDE Y-2 (11-647-22) 2 2 2 2 2 2 2 (11-654-22) RAFTER CAP Gg 2 8 2 2 (11-655-22) CORNER END BRACKET Hh 2 4 2 2 (08-158-22) BOLT Pp 3 196 2 2 (08-156-22) SCREW Qq 3 108 4 (08-167-22) SCREW Rr 3 12 25 ½” CENTER MIDDLE ROOF JOINT Z (11-677-22) 2 4 2 31” LEFT MID ROOF JOINT, 14’ SIDE Aa-2 (11-682-22) 43 ¼” LEFT LOWER CROSSBAR, 14’ SIDE DIAGRAM 58 7/8” 31” RIGHT MID ROOF JOINT, 14’ SIDE Aa (11-714-22
PART 3 12 16 QTY DIAGRAM PACKED IN BOX QTY PACKED IN BOX PART DIAGRAM (11-683-22) 53 ½” RIGHT LOWER CROSSBAR, 12’ SIDE 2 2 (08-193-22) PLASTIC PLUG Ss 2 2 (08-187-22) WASHER Tt 3 2 (11-697-22) CURTAIN RAIL CAP Uu 3 8 2 (08-189-22) ACORN NUT Vv 3 4 4 (11-686-22) SCREEN/M OUSTIQUAI RE Ww 2 4 2 (11-687V) PRIVACY CURTAIN Xx 2 4 1 4 3 96 Kk (11-718-22) 53 ½” LEFT LOWER CROSSBAR, 12’ SIDE Kk-2 (11-685-22) 20 ½” RIGHT UPPER CROSSBAR, 12’ SIDE 2 Ll (11-720-22) 20 ½” LEF
2 3 2 B CENTRAL HUB L (11-731-32) 92 5/8” ROOF RAFTER ROOF RAFTER N (11-637-32) 78 ¼” 60 3/8” TOP RIGHT BEAM D 3 2 (11-628-32) CORNER PLATE E 3 4 (11-629-32) CENTER PLATE F 3 4 ROOF RAFTER N-2 RAFTER M MOUNTING BRACKET O RAFTER N MOUNTING BRACKET P (11-638-32) 3 4 RIGHT FLASHING Q (11-639-32) 3 4 LEFT FLASHING R (11-640-32) 3 (11-663-32) (11-630-32) 81 ½” LEG G (11-631-32) FOOT PLATE H (11-632-32) CORNER COVER I (11-633-32) MIDDLE COVER J 2 4 2 6 2 2 2 4 2 8 2 4 2 4
TOP CAP K 2 1 2 4 (11-674-32) 1 2 31”x38” LEFT LOWER PANEL, 12’ SIDE Bb (11-721-32) LEFT LOWER PANEL, 14’ SIDE Bb-2 (11-679-32) 1 2 RIGHT LOWER PANEL, 12’ SIDE Cc (11-722-32) (11-734-32) 39”x57 ½” 37”x25 ½” RIGHT LOWER PANEL, 14’ SIDE Cc-2 (11-680-32) 1 4 1 2 (11-675-32) 37 ½”x30 ½” RIGHT UPPER PANEL, 14’ SIDE X QTY 2 1 2 1 2 1 2 LEFT EDGING, 12’ SIDE Dd (11-715-32) 2 2 2 2 2 4 72 5/8” 37 ½”x30 ½” 1 2 2 2 (11-676-32) 38 ½” LEFT MID ROOF JOINT, 12’ SIDE Y 1 72 5/8
PART (11-713-32) (11-653-32) 38 ½” 58 7/8” RIGHT MID ROOF JOINT 12’ SIDE Y-2 (11-647-32) 2 2 2 2 2 2 2 (11-654-32) RAFTER CAP Gg 2 8 2 2 (11-655-32) CORNER END BRACKET Hh 2 4 2 2 (08-158-32) BOLT Pp 3 196 2 2 (08-156-32) SCREW Qq 3 108 4 (08-167-32) SCREW Rr 3 12 25 ½” CENTER MIDDLE ROOF JOINT Z (11-677-32) 2 4 2 31” LEFT MID ROOF JOINT, 14’ SIDE Aa-2 (11-682-32) 43 ¼” LEFT LOWER CROSSBAR, 14’ SIDE DIAGRAM 58 7/8” 31” RIGHT MID ROOF JOINT, 14’ SIDE Aa (11-714-32
PART 3 12 16 QTY DIAGRAM PACKED IN BOX QTY PACKED IN BOX PART DIAGRAM (11-683) 53 ½” RIGHT LOWER CROSSBAR, 12’ SIDE 2 2 (08-193) PLASTIC PLUG Ss 2 2 (08-187) WASHER Tt 3 2 (11-697) CURTAIN RAIL CAP Uu 3 8 2 (08-189) ACORN NUT Vv 3 4 4 (11-686) SCREEN/ MOUSTIQ UAIRE Ww 2 4 2 (11-687) PRIVACY CURTAIN Xx 2 4 1 4 3 96 Kk (11-718) 53 ½” LEFT LOWER CROSSBAR, 12’ SIDE Kk-2 (11-685) 20 ½” RIGHT UPPER CROSSBAR, 12’ SIDE 2 Ll (11-720) 20 ½” LEFT UPPER CROSSBAR, 12’ SIDE
17 ZZZ-204.43224.1207-18.GP.EN.
MAINTENANCE NOTES 1. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts. 3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the roof and cause it to collapse. 4. While the product is designed for 4 seasons use, the roof must be kept free of accumulation of snow.