adlonco@hotmail.com 43224 12’x14’ GAZEBO ASSEMBLY INSTRUCTIONS Assembly with more than one person recommended 0 ZZZ-204.43224.0530-14.GP.EN.HER.
Before you assemble the Gazebo It is important that this gazebo be anchored on a solid base with the provided screws. Otherwise, please ensure that you use anchors sufficient for your surface. The gazebo should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the gazebo and cause it to collapse. Step 1: Assemble beams “A” and “B” using center plate “F”, securing tightly with 8 bolts “Pp”. Repeat with beams “C” and “D”, also using center plate “F”.
Step 3: Have someone lift the beam assembly and attach each leg “G” into a corner, securing each using 4 bolts “Pp”. Repeat until all four legs are in place. Step 4: Install middle joint cover “J” at each of the 4 beam junctions, using 4 screws “Qq” each. Install corner cover “I” at each of the corners, using 4 screws “Qq” each. 2 ZZZ-204.43224.0530-14.GP.EN.HER.
Step 5: Attach mounting brackets “O” to rafters “M”, and mounting brackets “P” to rafters “N” and “N-2”. Use threaded hole about 8” from end of rafter. Lift central hub “L” to a height of about 110” (2.79m) at the center of the gazebo. (Caution: this part may be heavy, use support as needed) Attach one end of rafter “M” to the hub using 1 bolt “Pp”. Attach other end with mounting bracket to the corner of the beam assembly with 2 bolts “Pp”. Use the set of holes closest to the inside.
Step 7: Install the flashings “Q”, “R”, “S”, and “S-2” onto the beam assembly, using screws “Qq” on the inside. The notched end of a flashing will always go in a corner of the gazebo. Step 8: Install the curtain rails “T” and “U” on the inside of the beam assembly using bolts “Pp”. Pp 4 ZZZ-204.43224.0530-14.GP.EN.HER.
Step 9: Slide the indicated polycarbonate panels into the spaces between the rafters, using the top groove of each rafter. Ensure the side meant to face the sun is on the outside. Use a rubber hammer to carefully tap each panel into the grooves. Step 10: Insert the middle roof joints in between the rafters and slide them up under the polycarbonate panels. Tap lightly to ensure the panel is fully in the slot. Seen from above, most of the joint as well as the drain holes should be beneath the roof panels.
Step 11: Slide the remaining polycarbonate roof panels in the lower groove of the rafters and into the lower slot of the roof joints. Tap to make sure panels fit securely and do not extend past the ends of the rafters. Step 12: Starting from any end, install all edgings, with end caps “Gg” or “Hh” at each junction or corner respectively. Use bolts “Pp” to secure. 6 ZZZ-204.43224.0530-14.GP.EN.HER.
Step 13: Install the upper crossbars on the interior of the roof using bolts “Pp”, following the shaped ends and letters. Do not tighten bolts immediately; install loose and tighten once all crossbars are in place. Repeat this step with the lower crossbars. Pp Pp Pp Step 14: a) Secure each foot plate into the ground using screws “Rr” and washers “Tt”. b) Use lag shields (Ss) if needed for harder surfaces. 7 ZZZ-204.43224.0530-14.GP.EN.HER.
Step 15: Install the screen curtains “Ww” in the interior groove of the curtain rails, using the provided hooks. Install the privacy curtains “Xx” in the exterior groove of the rails. Once the hooks are in, use curtain rail caps “Uu” to close ends of curtain rails. IMPORTANT NOTES: Make sure all screws and bolts are tight. If conditions are windy, you may have to add cable guides at the corners. 8 ZZZ-204.43224.0530-14.GP.EN.HER.
PART QTY DIAGRAM PART QTY 1 (11-626) 65 ½” TOP LEFT BEAM A 2 (11-665) 60” CENTRAL HUB L (11-627) 65 ½” TOP RIGHT BEAM B 2 (11-731) 92 5/8” ROOF RAFTER M 4 2 (11-708) 73 ¾” ROOF RAFTER N 6 2 (11-637) 60 3/8” ROOF RAFTER N-2 2 4 RAFTER M MOUNTING BRACKET O 4 (11-629) CENTER PLATE F 4 RAFTER N MOUNTING BRACKET P 8 (11-630) 81 ½” LEG G 4 (11-638) 55 ¼” RIGHT FLASHING Q 4 (11-631) FOOT PLATE H 4 (11-639) 55 ¼” LEFT FLASHING R 4 4 (11-640) 25 3/8” CENTER FLASHING S 2 4 (11-709
PART (11-641) 60 ½” CURTAIN RAIL, 12’ SIDE U (11-674) 31”x38” LEFT UPPER PANEL, 12’ SIDE V QTY 4 DIAGRAM PART (11-678) 32 ¼”x72” LEFT LOWER PANEL, 12’ SIDE Bb QTY 2 2 (11-721) 39”x57 ½” LEFT LOWER PANEL, 14’ SIDE Bb-2 2 2 (11-679) 32 ¼”x72” RIGHT LOWER PANEL, 12’ SIDE Cc 2 4 (11-722) 39”x57 ½” RIGHT LOWER PANEL, 14’ SIDE Cc-2 2 2 (11-680) 72 5/8” LEFT EDGING, 12’ SIDE Dd 2 (11-712) 37 ½”x30 ½” LEFT UPPER PANEL, 14’ SIDE X-2 2 (11-715) 72 5/8” RIGHT EDGING, 12’ SIDE Dd-2 2 (11-676) 38 ½”
PART QTY PART QTY 2 (08-158) BOLT Pp 196 2 (08-156) SCREW Qq 108 4 (08-167) SCREW Rr 12 2 (08-193) PLASTIC PLUG Ss 12 2 (08-187) WASHER Tt 16 2 (11-697) CURTAIN RAIL CAP Uu 8 2 (08-189) ACORN NUT Vv 4 4 (11-686) SCREEN CURTAIN Ww 4 2 (11-687) PRIVACY CURTAIN Xx 4 2 (11-698) 38”x25 ½” MIDDLE LOWER ROOF PANEL Yy 4 10 mm KEY 1 (11-682) 43 ¼” LEFT LOWER CROSSBAR, 14’ SIDE Ii (11-717) 43 ¼” RIGHT LOWER CROSSBAR, 14’ SIDE Ii-2 (11-657) 26 ¾” MIDDLE LOWER CROSSBAR Jj (11-683)
12 ZZZ-204.43224.0530-14.GP.EN.HER.
MAINTENANCE NOTES 1. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts. 3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the roof and cause it to collapse. 4. While the product is designed for 4 seasons use, the roof must be kept free of accumulation of snow.
