customerservice@gazebopenguin.com 41212-32 12 X 12 SOLARIUM ASSEMBLY INSTRUCTIONS DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS Two or more adults required for assembly Base Dimensions 12’ ½’’x12’ ½’’, Largest Dimensions 13’6’’x13’6’’ (see pg.
Before you assemble the Solarium Please don't destroy boxes until completely assembled. Please verify the content of each box against the list of parts. It is important that this solarium be installed on a solid base with the provided screws. Otherwise, please ensure that you use anchors sufficient for your surface. The solarium should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the solarium and cause it to collapse.
12x12 Solarium Assembly Instructions Step 1: Before starting to assemble, please decide where you would like to position the door panels. 1. Stand up the two panels (A), using two connecting pieces (E) affix the panels (A) together. 2. Stand up a frame meant to be next to the door (B) and a door frame (D), you can chose to place the door frame on the left side or on the right side, and then use two connecting pieces (E) to affix the panel and door frame. 3.
Step 2: 1. Slide top door rail (F) into wheels of sliding door (C). 2. Slide lower door rail (G) into the plastic guide of the sliding door(C). 3. Use bolt (Bb) to affix the plastic stoppers (H) one on each end of top door rail (F). 4. Use screw (Oo) to affix upper door rail end caps (Nn) one on each end of top door rail (F). Step 3: Please note the sliding door should be installed from the inside of the solarium. 1.
Step 4: 1. Attach roof rafters (L) to the central hub (N) using bolt (Bb). (Caution: hub may be heavy, use support if needed. 2. Use screw (Z) to affix the rafters (L) onto the top of panels going through the metal piece attached to the rafter (L). Rafters must be affixed where panels connect to each other. (2) (2) Step 5: Use the same method to assemble roof rafters (K) for the angled panels.
Step 6: Use nut (Hh) and washer (Gg) to affix the top cap (M) to the central hub (N). Step 7: First remove the protective layer from the PC roof panels, then insert them (Y, Aa, Ll) into the roof rafters according to the below drawing instructions. Note: the side that had the protective layer should face down. TOP VIEW ZZZ-182.41212-32.0607-18.GP.EN.
Step 8: After inserting the PC roof panels, insert the aluminum middle roof joints (O, P, Q) into the roof rafters. The below drawing view is from the inside of the solarium, looking up. Notes: The drain holes on the aluminum middle roof joints (O, P, Q) should be at the bottom.
Step 10: Once the PC roof is complete, use aluminum edging (S, U, W) to surround the edges of the PC roof using bolts (Bb) to fasten the rafter cap (R) and the edging, tighten securely. Step 11: Use the cross bars (T, V, X) to affix to the roof using bolts (Ff). ZZZ-182.41212-32.0607-18.GP.EN.
Step 12: Inside each of the panels (A, B), push two plastic plugs (Ii) into the ground, and then screw down the panels using two screws (Ee) for each panel. Special notes: 1. To remove windows (08-219), pull 1 pin out of the lock position and push the frame to the end of the track, then ease the window out of the tracks one side at a time. 2. To remove screening panel, first remove windows, then unscrew the 2 screws at the top corners of the screen frame. (2) (1) ZZZ-182.41212-32.0607-18.GP.EN.
08-129-32 REGULAR FRAME A 3 2 6 2 08-131-32 SLIDING DOOR 2 2 FRAME NEXT TO DOOR QTY 2 2 2 2 4 2 4 4 4 8 4 4 4 1 B SLIDING DOOR FRAME TOP DOOR 4 8 RAIL F Length 200.
08-145-32 MIDDLE ROOF JOINT 4 4 4 4 QTY IN BOX 4 4 RAFTER 4 12 4 4 4 4 4 4 4 24 4 48 CAP R 08-150-32 ROOF CROSS EDGING 4 4 Length 120.6 BAR T Length 94.5 cm cm 08-152-32 08-151-32 ROOF CROSS EDGING 4 4 Length 120.6 BAR V Length 94.
4 12 Cc LATCH 4 2 08-168-32 4 12 4 1 QTY IN BOX 4 20 4 39 4 20 1 4 1 4 4 4 4 12 08-167-32 SCREW WASHER PLASTIC PLUG Ii 08-195 08-196 (47” X47 ½”) (46 ½”x43”) 1 4 BOTTOM ROOF LEFT PANEL PANEL Kk Jj 08-197 08-198 (24 ¼” X42 ¼”) (46 ½”x43”) TOP ROOF 2 08-193 Hh CORNER 4 Gg 08-189-32 BOTTOM ROOF LATCH 08-187 Ff ACORN NUT RIGHT DOOR Ee Dd-L BOLT DRAWING Dd-R 08-169-32 LEFT DOOR DESCRIPTION 08-165-32 08-161-32 BOLT DRAWING PACKED QTY IN BOX PACK
AVAILABLE REPLACEMENT PARTS DESCRIPTION DRAWING DESCRIPTION 08-219-32 85-417-S PVC WINDOW ROUND SPLINE (in frame) FOR SCREENING 10-493 11-572-32 PVC WINDOW BOTTOM PLASTIC (replacement PANEL (for wall material only) panels) 85-417-P ROUND SPLINE FOR PVC WINDOW 11-822-32 BOTTOM PLASTIC PANEL (for doors) 15-123-32 15-097-32 PIN FOR PVC DOOR WHEEL WINDOW ASSEMBLY 13-033 10-458 PC WINDOW (for REPLACEMENT sliding door) WEATHERSTRIP 12-046-32 15-124-32 MOSQUITO MOUNTING SCREEN (
ZZZ-182.41212-32.0607-18.GP.EN.
MAINTENANCE NOTES 1. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts. 3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the roof and cause it to collapse. 4. While the product is designed for 4 seasons use, the roof must be kept free of accumulation of snow.