Quick Specs

Café™ 30" Five in One Oven
with 120V Advantium® Technology
CSB913P4NW2 / CSB913P2NS1 / CSB913P3ND1
For answers to your Café™ product questions, visit our website at cafeappliances.com.
WARRANTY
Parts warranty
Limited 1-year entire appliance
Limited 5-year magnetron tube
Labor warranty Limited 1-year entire appliance
Warranty notes See written warranty for full details
DIMENSIONS AND INSTALLATION INFORMATION
Note: Cabinets installed adjacent to wall ovens
must have an adhesion spec of at least a 194°F
temperature rating.
Note: 2" minimum between cutouts when installed
above warming drawer or single wall oven.
Installation information: Before installing, consult
installation instructions packed with product for
current dimensional data.
Note: Advantium 240 volt models cannot be
installed under 36 inches height.
Note: Use of the accessory drawer will replace
the bottom trim piece for applicable installations.
Please see installation instructions for full details.
1" MIN. above toekick or adjust
to oven installation height
2" MIN. between cutouts
3" MIN. between cutouts
recommended—2" MIN. required
Cutout height and width
per drawer requirements
Junction box location
A
B
Construct Solid Bottom
MIN. 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Each platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
4-3/16"
Conduit
(46" long)
Cabinet width
(240-volt models only)
21-1/2"
To back
of Control
20-1/4"
C
(Platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
C
L
2x4’s or
equivalent
solid floor
Suitable
bracing
to support
runners
21-5/8"
over centerline
of cabinet
25-1/4"
Cutout width
cabinet
width
Required
cutout location
36-3/4"
minimum
from floor
Junction box
location
(240-volt
models only)
4-3/16"
21-1/2"
To Back of Control
17-1/2"
Cutout height
A
B
23-1/2"
Cutout depth
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
Construct Solid Bottom
MIN. 3/8" Plywood
Supported by 2 x 4
or 1 x 2 Runners,
all Four Sides.
(Platform must be
able to support cabinet
load, weight of oven,
and additional
oven loads)
Conduit
(48-1/2"
long)
20-1/4"
29-3/4"
C
A = The unit overlap is 1-3/4" but allow 1-7/8" clearance from top edge of cutout
B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutout
C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout
29-3/4"
1" MIN. above toekick or adjust
to oven installation height
2" MIN. between cutouts
3" MIN. between cutouts
recommended—2" MIN. required
Cutout height and width
per drawer requirements
Junction box location
A
B
Construct Solid Bottom
MIN. 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Each platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
4-3/16"
Conduit
(46" long)
Cabinet width
(240-volt models only)
21-1/2"
To back
of Control
20-1/4"
C
(Platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
C
L
2x4’s or
equivalent
solid floor
Suitable
bracing
to support
runners
21-5/8"
over centerline
of cabinet
25-1/4"
Cutout width
cabinet
width
Required
cutout location
36-3/4"
minimum
from floor
Junction box
location
(240-volt
models only)
4-3/16"
21-1/2"
To Back of Control
17-1/2"
Cutout height
A
B
23-1/2"
Cutout depth
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
Construct Solid Bottom
MIN. 3/8" Plywood
Supported by 2 x 4
or 1 x 2 Runners,
all Four Sides.
(Platform must be
able to support cabinet
load, weight of oven,
and additional
oven loads)
Conduit
(48-1/2"
long)
20-1/4"
29-3/4"
C
A = The unit overlap is 1-3/4" but allow 1-7/8" clearance from top edge of cutout
B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutout
C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout
29-3/4"