Installation Instructions

ManualsBrandsGE Appliances ManualsDouble Oven Ranges30" Free-Standing Gas Double Oven Convection Range

TOOLS YOU WILL NEED MATERIALS YOU MAY

NEED

 Gas line shut-off valve

 Pipe joint sealant or UL-approved pipe thread

tape with Teflon* that resists action of natural

and propane gases

 Flexible metal appliance connector (1/2”

I.D.). A 5-foot length is recommended for

ease of installation but other lengths are

acceptable. Never use an old connector

when installing a new range.

 Flare union adapter for connection to gas

supply line (3/4” or 1/2” NPT x 1/2” I.D.)

 Flare union adapter for connection to

pressure regulator on range (1/2” NPT x 1/2”

I.D.)

 Liquid leak detector or soapy water.

*Teflon: Registered trademark of DuPont

Flat-blade

screwdriver

Pipe wrenches (2)

(one for backup)

Phillips

screwdriver

Open-end or

adjustable wrench

Pencil and ruler

Level

Drill, awl or nail

IN THE COMMONWEALTH

OF MASSACHUSETTS

 This product must be installed by a licensed

plumber or gas fitter.

 When using ball type gas shut-off valves,

they shall be the T-handle type.

 A flexible gas connector, when used, must

not exceed 3 feet.

Installation Instructions

Range

Questions? Call 800.GE.CARES (800.432.2737) or visit GEAppliances.com

BEFORE YOU BEGIN

IMPORTANT —

Save these

instructions for local inspector’s use.

IMPORTANT — Observe all

governing codes and ordinances.

IMPORTANT — Remove all packing

material and literature from oven before

connecting gas and electrical supply to range.

IMPORTANT — To avoid damage

to your cabinets, check with your builder

or cabinet supplier to make sure that the

materials used will not discolor, delaminate

or sustain other damage. This oven has been

designed in accordance with the requirements

of UL and CSA International and complies

with the maximum allowable wood cabinet

temperatures of 194°F (90°C).

Note to Installer – Be sure to leave these

instructions with consumer.

Note to consumer – Keep these instructions for

future reference.

Servicer – The electrical diagram is in an

envelope attached to the back of the range.

Proper installation is the responsibility of the

installer.

Product failure due to improper installation is

not covered under warranty.

Before installing your range on linoleum or

any other synthetic floor covering, make sure

the floor covering can withstand 180°F without

shrinking, warping or discoloring. Do not install

the range over carpeting unless a sheet of

1/4” thick plywood or similar insulator is placed

between the range and carpeting.

Mobile Home - Additional Installation

Requirements

The installation of this range must conform

to the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile

Home Construction and Saftey, Title 24,

HUD Part 280). When such standard is not

applicable, use the Standard for Manufactured

Home Installations, ANSI A225.1/NFPA 501A

or with local codes.

In Canada, the installation of this range must

conform with the current standards CAN/CSA-

A240-latest edition, or with local codes.

When this range is installed in a mobile home,

it must be secured to the floor during transit.

Any method of securing the range is adequate

as long as it conforms to the standards listed

above.

WARNING

FIRE OR EXPLOSION

HAZARD

If the information in this manual is not followed

exactly, a fire or explosion may result causing

property damage, personal injury or death.

Installation must be performed by a qualified

installer.

Read these instructions completely and

carefully.

Installation of this range must conform with

local codes, or in the absence of local codes,

with the National Fuel Gas Code, ANSI

Z223.1/NFPA.54, latest edition. In Canada,

installation must conform with the current

Natural Gas Installation Code, CAN/CGA-

B149.1 or the current Propane Installation

Code, CAN/CGA-B149.2, and with local codes

where applicable. This range has been design-

certified by CSA International according to

ANSI Z21.1, latest edition and Canadian Gas

Association according to CAN/CGA-1.1 latest

edition.

When installing a gas appliance the use of old

flexible connectors can cause gas leaks and

personal injury. Always use a NEW flexible

connector.

Leak testing of the appliance shall be

conducted according to the manufacturer

instructions.

The range must be electrically grounded

in accordance with local codes or, in the

absence of local codes, in accordance with

the National Electrical Code (ANSI/NFPA 70,

latest edition). In Canada, electrical grounding

must be in accordance with the current CSA

C22.1 Canadian Electrical Code Part 1 and/or

local codes. See Electrical Connections in this

section.

Do not install this product with an air curtain

hood or other range hood that operates by

blowing air down on the cooktop. This airflow

may interfere with operation of the gas burners

resulting in fire or explosion hazard.

FOR YOUR SAFETY:

• A child or adult can tip the range and be killed.

• Install the anti-tip bracket to the wall or floor.

• Engage the range to the anti-tip bracket by sliding the

range back such that the foot is engaged.

• Re-engage the anti-tip bracket if the range is moved.

• Failure to do so can result in death or serious burns

to children or adults.

Tip-Over Hazard

WARNING

Before beginning

the installation, switch power off at

service panel and lock the service

disconnecting means to prevent power

from being switched on accidentally.

When the service disconnecting means

cannot be locked, securely fasten a

prominent warning device, such as a

tag, to the service panel.

If you did not receive an anti-tip bracket with your

purchase, call 800.626.8774 to receive one at no

cost. (In Canada, call 800.561.3344.) For installation

instructions of the bracket, visit: GEAppliances.com.

(In Canada, GEAppliances.ca.)

Anti-Tip Bracket

Kit Included

Summary of content (8 pages)

PAGE 1
Installation Instructions Range Questions? T his product must be installed by a licensed plumber or gas fitter. WARNING FIRE OR EXPLOSION HAZARD If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. Installation must be performed by a qualified installer. Read these instructions completely and carefully.
PAGE 2
DIMENSIONS AND CLEARANCES Provide adequate clearances between the range and adjacent combustible surfaces. These dimensions must be met for safe use of your range. Allow 30” (76.2 cm) minimum clearance between burners and bottom of unprotected wood or metal cabinet, or allow a 24” (61 cm) minimum when bottom of wood or metal cabinet is protected by no less than 1/4” (6.4 mm) thick flame-retardant millboard covered DIMENSIONS AND CLEARANCES (CONT.) with no less than No. 28 MSG sheet metal (.015” [.
PAGE 3
1 G AS SUPPLY WARNING Fire Hazard: Do not use a flame to check for gas leaks. WARNING Explosion Hazard: Do not exceed 25 ft-lbs of torque when making gas line connections. Overtightening may crack the pressure regulator resulting in fire or explosion hazard. Gas Pressure Regulator You must use the gas pressure regulator supplied with this range.
PAGE 4
CHECK SURFACE BURNERS Push and turn a knob to the LITE position. A clicking sound indicates proper operation of the ignition system. When lighting any burner, sparks will appear at all burners but gas flows from only the one selected. Once air is purged from the supply line, burner should light within 4 seconds. After burner lights, rotate the knob out of the LITE position. Try each burner in succession until all burners have been checked. Quality of Flames Determine the quality of flames visually.
PAGE 5
Instrucciones de Instalación Cocina HERRAMIENTAS Destornillador Philips Ante cualquier duda, llame al 800-GE-CARES o visite nuestro sitio web en: GEAppliances.com Destornillador con cabeza plana En el Commonwealth de Massachusetts • Este producto debe ser instalado por un plomero licenciado o un mecánico gasista.
PAGE 6
DIMENSIONES Y ESPACIOS Deje el espacio adecuado entre la cocina y las superficies combustibles adyacentes. Estas dimensiones se deberán cumplir para un uso seguro de su cocina. Deje un espacio mínimo de 30” (76.2 cm) entre los quemadores y la parte inferior del gabinete de madera o metal sin protección, o deje un espacio mínimo de 24” (61 cm) cuando la parte inferior del gabinete de madera o metal esté protegido por no menos de 1/4” (6.
PAGE 7
1 S UMINISTRO DE GAS ADVERTENCIA Riesgo de incendio: No use una llama para controlar las pérdidas de gas. ADVERTENCIA Riesgo de Explosión: No supere una torsión máxima de 25 pies-libras al realizar conexiones de tuberías de gas. Cualquier ajuste en exceso podrá romper el regulador de presión, resultando en riesgo de incendio o explosión. Regulador de Presión de Gas Se deberá usar el regulador de presión de gas suministrado con esta cocina.
PAGE 8
4 CONTROLE LAS CABEZAS DE LOS QUEMADORES Presione y gire la perilla a la posición LITE (Luz). Un sonido de clic indica el correcto funcionamiento del sistema de encendido. Al iluminar cualquier quemador, se producirán chispas en todos los quemadores pero sólo saldrá gas del que fue seleccionado. Una vez que el aire se haya purgado de la línea de suministro, el quemador se deberá encender dentro de los 4 segundos. Luego de que el quemador se encienda, gire la perilla fuera de la posición LITE (Luz).