Installation Sheet

ManualsBrandsGE Appliances ManualsGE SlateGE 30" Built-In Microwave Trim Kit

Installation

Microwave Oven

Instructions

Built-In Trim Kits

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT ³ Save these instructions

for local inspector’s use.

•

IMPORTANT ³ Observe all governing codes and

ordinances.

•

Note to Installer – Be sure to leave these instructions with

the Consumer.

• Note to Consumer – Keep these instructions for future

reference.

• Skill level – Installation of this appliance requires basic

mechanical and electrical skills.

• Completion time –

1 to 3 hours

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered

under the Warranty.

• This kit is for use on models:PEB9159DJ, PEB9159SJ,

PEB9159EJ and CEB1599SJ.

• This kit and microwave are approved for installation alone

or above any single electric wall oven. Do not mount

adjacent (within 2 feet) to any range, cooktop, gas oven, or

other microwave.

• This product is to be installed 3 feet above floor level.

• Do not alter or modify any part of this kit or the oven.

• For easier installation and personal safety, we

recommend that two people install this microwave oven.

• Unplug the microwave oven before attempting installation

of this kit.

WARNING

³ This oven must be plugged into a

properly grounded 3-hole, 120 volt receptacle as required by

the National Electrical Code.

WARNING

³ Before beginning the installation,

switch power off at service panel and lock the service

disconnecting means to prevent power from being switched

on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at: GEAppliances.com

PARTS INCLUDED

NOTE: This kit has extra screws to prevent the technician

from spending extra time locating a replacement in case

they lose one during installation.

JX9152 and JX9153

PART QUANITY

Rear Duct 1

Bottom Duct

Trim Kit

Frame

Rail

Short Screws

16 required

3 extra

Long Wood

Screws 4 required

2 extra

Summary of content (8 pages)

PAGE 1
Installation Instructions Microwave Oven Built-In Trim Kits JX9152 and JX9153 Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at: GEAppliances.com BEFORE YOU BEGIN PARTS INCLUDED Read these instructions completely and carefully. • ³ Save these instructions for local inspector’s use. IMPORTANT • PART QUANITY IMPORTANT ³ Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer.
PAGE 2
Installation Instructions TOOLS YOU WILL NEED GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
PAGE 3
Installation Instructions 3 INSTALL THE REAR DUCT 1 LOCATE AND INSTALL THE BASE PAN 1. Gently return microwave oven to its upright position. 2. Remove screw A. Set Base Pan into the front cabinet microwave oven cutout and center it right and left. Push back until the front flange is against the cabinet front wall. Mount the Base Pan using 3 short screws. Short Screw Screw A 3. Align the rear duct with the back of microwave oven, as shown. Base Pan Mounting Holes 2 INSTALL THE RAILS 4.
PAGE 4
Installation Instructions 3 INSTALL THE REAR DUCT (continued) 6 SECURE THE RAILS TO THE CABINET 6. Use 3 short screws to secure back of rear duct to the back of microwave oven, as shown. Ensure the Base Pan and Bottom Bracket front flanges are tight against the cabinet, and that the screws holes are aligned. Drive 4 short screws through the Base Pan and Rails into the cabinet Mounting Holes A B C A. Short screws (3) B. Rear duct C.
PAGE 5
Instrucciones de Instalación Kits de Horno Microondas con Terminaciones Incorporadas JX9152 y JX9153 ¿Preguntas? Llame a 800.GE.CARES (800.432.2737) o Visite nuestro sitio web en: GEAppliances.com ❒ ANTES DE COMENZAR PIEZAS INCLUIDAS Lea estas instrucciones en su totalidad y atentamente. • ³ Conserve estas instrucciones para uso del inspector local. • ³ Cumpla con todos los códigos y ordenanzas gubernamentales. • Nota para el Instalador – Asegúrese de que el Comprador conserve estas instrucciones.
PAGE 6
Instrucciones de Instalación HERRAMIENTAS QUE NECESITARÁ INSTRUCCIONES DE CONEXIÓN A TIERRA Este electrodoméstico deberá estar conectado a tierra. En caso de que se produzca un cortocircuito, la conexión a tierra reduce el riesgo de descarga eléctrica, brindando un cable de escape de la corriente eléctrica. Este electrodoméstico está equipado con un cable de corriente que posee un cable de conexión a tierra con un enchufe a tierra.
PAGE 7
Instrucciones de Instalación 3 INSTALACIÓN DEL CONDUCTO TRASERO 1 UBIQUE E INSTALE UNA OLLA DE LA BASE 1. De forma suave gire el horno microondas hasta su posición vertical. 2. Retire el tornillo A. Coloque la Olla de la Base en la abertura del gabinete frontal del horno microondas y centre la misma sobre la derecha y la izquierda. Empuje hacia atrás hasta que la pestaña frontal quede contra la pared frontal del gabinete. Monte la Olla de la Base usando 3 tornillos cortos.
PAGE 8
Instrucciones de Instalación 4 INSTALE EL HORNO MICROONDAS 6 ASEGURE LOS RIELES AL GABINETE Asegure que la Olla de la Base y las lengüetas frontales del Soporte Inferior estén ajustadas contra el gabinete, y que los agujeros de los tornillos estén alineados. Coloque 4 tornillos cortos a través de la Olla de la Base y los Rieles sobre el gabinete. Enchufe el cable de corriente en el tomacorriente.