Quick Specs
For answers to your Monogram, GE Café
™
, GE Profile
™
or GE Appliances
product questions, visit our website at geappliances.com or call
GE Answer Center
®
Service, 800.626.2000.
Specification Revised 10/20
Listed by
Underwriters
Laboratories
PSB9240SF
GE Profile
™
Series 30 in. Single Wall Oven with Advantium
®
Technology
1" Min. above toekick or adjust
to oven installation height
2" MIN between cutouts
3" MIN between cutouts
recommended—2" MIN required
Cutout height and width
per drawer requirements
Junction box location
A
B
Construct Solid Bottom
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Each platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
4-3/16
Conduit
(46" long)
Cabinet width
(240-volt models only)
21-1/2"
To back
of Control
19"
C
L
2x4’s or
equivalent
solid floor
Suitable
bracing
to support
runners
21-5/8"
over centerline
of cabinet
25-1/4"
Cutout width
cabinet
width
Required
cutout location
36-3/4"
minimum
from floor
Junction box
location
(240-volt
models only)
4-3/16"
21-1/2"
To Back of Control
17-1/2"
Cutout height
A
B
23-1/2"
Cutout depth
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
Conduit
(48-1/2"
long)
19"
29-3/4"
C
(Platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
A = The unit overlap is 1/2" but allow 5/8" clearance from top edge of cutout
B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutout
C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout
Construct Solid Bottom
MIN. 3/8" Plywood
Supported by 2 x 4
or 1 x 2 Runners,
all Four Sides.
(Platform must be
able to support cabinet
load, weight of oven,
and additional
oven loads)
C
29-3/4"
1" Min. above toekick or adjust
to oven installation height
2" MIN between cutouts
3" MIN between cutouts
recommended—2" MIN required
Cutout height and width
per drawer requirements
Junction box location
A
B
Construct Solid Bottom
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Each platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
4-3/16
Conduit
(46" long)
Cabinet width
(240-volt models only)
21-1/2"
To back
of Control
19"
C
L
2x4’s or
equivalent
solid floor
Suitable
bracing
to support
runners
21-5/8"
over centerline
of cabinet
25-1/4"
Cutout width
cabinet
width
Required
cutout location
36-3/4"
minimum
from floor
Junction box
location
(240-volt
models only)
4-3/16"
21-1/2"
To Back of Control
17-1/2"
Cutout height
A
B
23-1/2"
Cutout depth
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
Conduit
(48-1/2"
long)
19"
29-3/4"
C
(Platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
A = The unit overlap is 1/2" but allow 5/8" clearance from top edge of cutout
B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutout
C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout
Construct Solid Bottom
MIN. 3/8" Plywood
Supported by 2 x 4
or 1 x 2 Runners,
all Four Sides.
(Platform must be
able to support cabinet
load, weight of oven,
and additional
oven loads)
C
29-3/4"
NOTE: Cabinets
installed adjacent
to wall ovens must
have an adhesion
spec of at least a
194°F temperature
rating.
NOTE: 2" minimum
between cutouts
when installed
above warming
drawer or single
wall oven.
INSTALLATION
INFORMATION:
Before installing,
consult installation
instructions packed
with product for current
dimensional data.
ADVANTIUM WALL OVEN/GE PROFILE
™
SERIES COOK-
ING TOWER DIMENSIONS AND CABINET INSTALLATION
INFORMATION (IN INCHES)
NOTE: Advantium 240 volt models cannot be installed under 36 inches height.
NOTE: Use of the accessory drawer will replace the bottom trim piece for
applicable installations. Please see installation instructions for full details.
1" Min. above toekick or adjust
to oven installation height
2" MIN between cutouts
3" MIN between cutouts
recommended—2" MIN required
Cutout height and width
per drawer requirements
Junction box location
A
B
Construct Solid Bottom
MIN 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides.
(Each platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
4-3/16
Conduit
(46" long)
Cabinet width
(240-volt models only)
21-1/2"
To back
of Control
19"
C
L
2x4’s or
equivalent
solid floor
Suitable
bracing
to support
runners
21-5/8"
over centerline
of cabinet
25-1/4"
Cutout width
cabinet
width
Required
cutout location
36-3/4"
minimum
from floor
Junction box
location
(240-volt
models only)
4-3/16"
21-1/2"
To Back of Control
17-1/2"
Cutout height
A
B
23-1/2"
Cutout depth
Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
Conduit
(48-1/2"
long)
19"
29-3/4"
C
(Platform must be able to support
cabinet load, weight of oven, and
additional oven loads)
A = The unit overlap is 1/2" but allow 5/8" clearance from top edge of cutout
B = The unit overlap is 2-1/4" but allow 2-3/8" clearance from side edges of cutout
C = The unit overlap is 1" but allow 1-1/8" clearance from bottom edge of cutout
Construct Solid Bottom
MIN. 3/8" Plywood
Supported by 2 x 4
or 1 x 2 Runners,
all Four Sides.
(Platform must be
able to support cabinet
load, weight of oven,
and additional
oven loads)
C
29-3/4"