Installation Instructions

ManualsBrandsGE Appliances ManualsAir & WaterPortable AC Dual Hose Conversion Kit

Parts Included:

1. Dual Hose Conversion Baffles (2)

2. Intake Hose Adapter to AC

3. Intake Hose Adapter to Window Kit

4. Intake Hose

5. Exhaust Hose Insulation

6. Dual Hose Window Panel

31-5000578 Rev. 1 03-21 GEA

Installation Instructions

for your new

Before you begin - Read these instructions completely and carefully.

IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.

Note to Installer – Be sure to leave these instructions with the Consumer.

Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.

RAP02 Dual Hose

Conversion Kit

Tools Needed

• Phillips head screwdriver • Small hand saw - if trimming of the

window expansion panels is required

2.3.

Summary of content (8 pages)

PAGE 1
Installation Instructions for your new RAP02 Dual Hose Conversion Kit Before you begin - Read these instructions completely and carefully. IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions with your Owner’s Manual for future reference. Tools Needed • Phillips head screwdriver • Small hand saw - if trimming of the window expansion panels is required Parts Included: 1. 2. 3. 4. 5. 6.
PAGE 2
Safety IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electrical • Disconnect power before cleaning. NOTE: Turning off power by pressing the Power button does NOT disconnect the appliance from the power supply. • Do not install or use the air conditioner in any area where the atmosphere contains combustible gases or where the atmosphere is contaminated. Avoid any chemicals coming in contact with your air conditioner. • Do not store anything directly on top of the air conditioner.
PAGE 3
Installation Instructions Converting GE Portable Air Conditioner to Dual Hose Configuration STEP 3: Installing the Exhaust Hose Insulating Sleeve STEP 1: Unplug or disconnect power WARNING If you previously installed your GE Portable Air Conditioner, you will need to remove the Window Kit from the window and then remove the Exhaust Hose Adapter from the Window Kit.
PAGE 4
Installation Instructions STEP 4: Attach the Dual Hose Conversion Baffle to the Back of the Air Conditioner STEP 5: Assemble Intake Hose Assembly and Mount to back of Unit Using the parts that were included in the Dual Hose Conversion Kit, extend the intake hose approximately 4” from each end. Screw the adapters onto the ends of the hose, turning clockwise until they are secure.
PAGE 5
Instrucciones de Instalación para su nuevo Kit de Conversión con Manguera Doble RAP02 Antes de comenzar – lea estas instrucciones completamente y de forma detenida. IMPORTANTE- CUMPLA CON TODOS LOS CÓDIGOS Y ORDENANZAS GUBERNAMENTALES. Nota para el Instalador – Asegúrese de entregar estas instrucciones al Consumidor. Nota para el Consumidor – Guarde estas instrucciones con su Manual del Propietario para referencia futura.
PAGE 6
INSTRUCCIONES IMPORTANTES DE SEGURIDAD • Desconecte el suministro de energía antes de darle servicio técnico. ADVERTENCIA Para reducir el riesgo de incendio, choque eléctrico, lesiones a personas o daños al utilizar el acondicionador de aire, siga precauciones básicas, incluyendo las siguientes: • Desconecte el suministro de energía antes de limpiarlo.. NOTA: Si apaga la unidad presionando el botón Power (Encendido), esto NO desconecta el electrodoméstico del suministro de energía.
PAGE 7
Instrucciones de instalación Conversión del Acondicionador de Aire Portátil de GE Appliances a una Configuración con Manguera Doble PASO 3: Instalación de la Manga Aislante de la Manguera de Salida PASO 1: Desenchufe o desconecte la corriente. Si de forma previa instaló su Acondicionador de Aire Portátil de GE Appliances, será necesario retirar el Kit de Ventana de esta última y luego retirar el Adaptador de la Manguera de Salida del Kit de Ventana.
PAGE 8
Instrucciones de instalación PASO 4: Adhiera el Deflector de Conversión de la Manguera Doble sobre la Parte Trasera del Acondicionador de Aire PASO 5: Instale el Ensamble de la manguera de entrada y monte el mismo sobre la parte trasera de la unidad Usando las piezas incluidas con el kit de conversión de la manguera doble, extienda la manguera de entrada aproximadamente 4” desde cada extremo.