Specification
CGS990SETSS
GE Café
™
Series 30" Slide-In Front Control Gas
Double Oven with Convection Range
Specification Revised 2/16
For answers to your Monogram, GE Café
™
Series, GE Profile
™
Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center
®
Service, 800.626.2000.
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
ELECTRICAL REQUIREMENTS: 120v; 60Hz, 15A
INSTALL ATION INFORMATION: Before installing,
consult installation instructions packed with product
for current dimensional data.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
Gas Pipe and Electrical Outlet Locations
Minimum to
cabinets on
either side
of the range.
Minimum
clearance
to left wall
Minimum
Minimum
clearance to
right wall
Maximum
depth for
cabinets above
countertops
Front edge of
the range side
panel forward
from cabinet
To cabinets below cooktop
and at the range back
(Some models will not have
0" clearance.)
To cabinets
below
cooktop and
at the range
back
18"
6"
30"
30"
13"
6"
36"
0"
0"
1/4"
*Dimensions are referenced from the point at the
back of the range that will contact the rear wall first.
36 1/4" +/- 1/4"
26 3/4"
w/o handle
29 1/2"
w/handle
*43 3/4"
*Dimension are referenced from the point at
the back of the range that will contact the rear
wall first. Max dimension should be considered
between the upper and lower doors.
**Height to backguard based on Café style
backguard kit installed.
Recommended area 120V
outlet on rear wall and area for
through-the-wall connection
of pipe stub and shut-off valve.
Recommended area
for through-the-floor
connection of pipe stub
and shut-off valve.
To prevent drafts from affecting burner
operation, seal all openings in floor and wall.
30"
For island installation, Model CGS990, maintain 2-1/2" minimum from cutout to back edge of countertop and 3"
minimum from cutout to side edges of countertop.
CAUTION
30"
4"
5"
9"
8"
2"
3"
1 1/2"
CGS990
14 1/2"
4 1/2"
Gas Pipe and Electrical Outlet Locations
Minimum to
cabinets on
either side
of the range.
Minimum
clearance
to left wall
Minimum
Minimum
clearance to
right wall
Maximum
depth for
cabinets above
countertops
Front edge of
the range side
panel forward
from cabinet
To cabinets below cooktop
and at the range back
(Some models will not have
0" clearance.)
To cabinets
below
cooktop and
at the range
back
18"
6"
30"
30"
13"
6"
36"
0"
0"
1/4"
*Dimensions are referenced from the point at the
back of the range that will contact the rear wall first.
36 1/4" +/- 1/4"
26 3/4"
w/o handle
29 1/2"
w/handle
*43 3/4"
*Dimension are referenced from the point at
the back of the range that will contact the rear
wall first. Max dimension should be considered
between the upper and lower doors.
**Height to backguard based on Café style
backguard kit installed.
Recommended area 120V
outlet on rear wall and area for
through-the-wall connection
of pipe stub and shut-off valve.
Recommended area
for through-the-floor
connection of pipe stub
and shut-off valve.
To prevent drafts from affecting burner
operation, seal all openings in floor and wall.
30"
For island installation, Model CGS990, maintain 2-1/2" minimum from cutout to back edge of countertop and 3"
minimum from cutout to side edges of countertop.
CAUTION
30"
4"
5"
9"
8"
2"
3"
1 1/2"
CGS990
14 1/2"
4 1/2"
Gas Pipe and Electrical Outlet Locations
Minimum to
cabinets on
either side
of the range.
Minimum
clearance
to left wall
Minimum
Minimum
clearance to
right wall
Maximum
depth for
cabinets above
countertops
Front edge of
the range side
panel forward
from cabinet
To cabinets below cooktop
and at the range back
(Some models will not have
0" clearance.)
To cabinets
below
cooktop and
at the range
back
18"
6"
30"
30"
13"
6"
36"
0"
0"
1/4"
*Dimensions are referenced from the point at the
back of the range that will contact the rear wall first.
36 1/4" +/- 1/4"
26 3/4"
w/o handle
29 1/2"
w/handle
*43 3/4"
*Dimension are referenced from the point at
the back of the range that will contact the rear
wall first. Max dimension should be considered
between the upper and lower doors.
**Height to backguard based on Café style
backguard kit installed.
Recommended area 120V
outlet on rear wall and area for
through-the-wall connection
of pipe stub and shut-off valve.
Recommended area
for through-the-floor
connection of pipe stub
and shut-off valve.
To prevent drafts from affecting burner
operation, seal all openings in floor and wall.
30"
For island installation, Model CGS990, maintain 2-1/2" minimum from cutout to back edge of countertop and 3"
minimum from cutout to side edges of countertop.
CAUTION
30"
4"
5"
9"
8"
2"
3"
1 1/2"
CGS990
14 1/2"
4 1/2"