Compatibility Requirements Works with C by GE Smart Lights, Plugs, Switches, and Sensors. Not compatible with non-C by GE Smart devices. Note: Switch and other C by GE lights, plugs and switches must be grouped in the same Room/Space in the C by GE opp to enable full room control.
•••
You Got This! And we're here to help. For in-depth instructional videos and a guided tour through the installation, go to cbyge.com/wirefree-support.
BEFORE YOU DO ANYTHING: STEP 1 Location & Mounting Type Decide how you want to mount your switch This switch can be mounted to the wall in two ways, by screws or adhesive tape. Once you determine which install method is best for you, select one of the following setup methods. For Help, Go To: cbyge.
STEP 2 Installing Your Switch (mounting with adhesive tape) IMPORTANT Start by removing the clear plastic tab from the back of the switch. 1. Identify where you want to mount your Wire-Free Switch (switches are typically located '48-52" from the floor to the top of the switch). 2. Prior to installation, be sure that the surface is smooth and degreased. 3. Apply adhesive tape to the middle back of the switch. Adhesive tab should stick out from the side of the switch.
STEPS 1, 2 & 3 • C) STEPS ~ & 5 • C) ,Q • C) • 0 • For Help, Go To: cbyge.
STEP 2 Alternative Mounting Installing Your Switch (mounting with screws/single-gang wallplate) IMPORTANT Start by removing the clear plastic tab from the back of the switch. 1. Identify where you want to mount your Wire-Free Switch (switches are typically located '48-52" from the floor to the top of the switch). 2. Mark the location for holes to be drilled. We suggest using the mounting holes on the switch housing as a guide. Use the level (optional) to ensure the switch is level before drilling holes.
STEPS l & 2 0 • ···K 0 .. •)( • STEPS~ & 5 STEP 3 For Help, Go To: cbyge.
STEP 2 Alternative Mounting Installing Your Switch (mounting with screws/2-gang wallplate) IMPORTANT Start by removing the clear plastic tab from the back of the switch. 1. Remove existing wallplate 2. Get multi-gang wallplate (purchased separately). 3. Use new wallplate to mark the location for holes to be drilled. I.e. Using 7/32" bit, drill holes in wall for mounting screws. Insert drywall anchors. 5. Secure the switch to the wall until level and flush. 6.
STEPS l & 2 STEPS 1-t - 6 • 0 0 • STEP 3 X For Help, Go To: cbyge.
II • • Keep sw1 ch control entering a room after moving furniture and plugging lamps into different sockets I _,·
•
Removing/Replacing (uses one CR2032 the Battery coin battery) 1. Remove the switch from the wall. • 0 • • ~ 0 0 ~ 2. Remove rear housing of the switch using Phillips screwdriver. 3. Slide the battery out, towards the top of the switch. i.. Slide a new battery underneath the contact strap, with the (+) terminal toward the back of the switch. 5. Replace rear housing. .... • C • .... ~ 0 • 0 ..._ ....
FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This device complies with Part 15 of the FCC Rules.
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d'lndustrie Canada applicables aux appareils radio exempts de licence.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet emetteur ne doit pas etre Co-place ou ne fonctionnant en meme temps qu'aucune autre antenne ou emetteur. Cet equipement devrait etre installe et actionne avec une distance minimum de 20 centimetres entre le radiateur et votre corps.
Like your new C by GE Smart Switch? Share your experience! Leave a review where you purchased the product.
b)+'=+ Install Download Add your Smart Switch and Smart Bulb the C by GE opp your Smart Bulb and Wire-Free Smart Switch to the C by GE opp in the same room/group Set up your Wire-Free Smart Switch and Smart Bulb in the C by GE app in the same room See Wire-Free Smart Switch Installation Guide for more details. For help and training videos, visit cbyge.
Let's illuminate what your Wire-Free Smart Switch + Smart Bulb can do together G) Turn on all the lights in a room with one touch. Go to the C by GE app add the Smart Bulb and Wire-Free Smart Switch to the same room under create an automation. @ Automate your lights to turn on when you come home. Go to the C by GE app and schedule the times to turn lights on and off under create an automation. @ Set the mood for movie night.