User Manual
Table Of Contents
- Copyright and Trademark
- RF Safety Notice (English and French)
- FCC Part 15 Notice
- Industry Canada Notice
- 1.0 INTRODUCTION
- 2.0 PRODUCT DESCRIPTION
- 3.0 APPLICATIONS
- 4.0 INSTALLATION PLANNING
- 5.0 STEP-BY-STEP INSTALLATION
- 6.0 TRANSCEIVER MANAGEMENT
- 6.1 Software Commands
- Entering Commands
- AK
- ALARM
- AMASK [0000 0000–FFFF FFFF]
- ASENSE [HI, LO]
- AUDIO [ON, OFF]
- BAUD [xxxxx abc]
- BIN [DATA, CLEAR]
- BOOT
- BUFF [ON, OFF]
- CKEY [ON–OFF]
- CTS [0–255]
- CTSHOLD [0–60000]
- DATAKEY [ON, OFF]
- DEV
- DEVICE [DCE, CTS KEY]
- DKEY
- DLINK [ON/OFF/xxxx]
- DTYPE [NODE/ROOT]
- DUMP
- EMP [ON/OFF]
- ETHADDR
- FORCEALARM [ON or OFF]
- FORCEDCD [ON or OFF]
- HELP
- INIT
- INIT [SDx]
- INIT [P-20]
- IPCONFIG
- KEY
- MENU
- MODEL1
- MODEL2
- MODEM [xxxx]
- OWM [XXX...]
- OWN [XXX...]
- PORT [RS232, RS485]
- PTT [0–255]
- PTTSIG [OFF, LOW, HI]
- PWR [20–37]
- RESTORECONFIG
- RESTOREDEFAULTS
- RMODE [X710, TRANSPARENT, PACKET, CMAC, HELP]
- RSSI
- RTSKEY [ON, OFF]
- RTU [ON/OFF/0-80]
- RX [xxx.xxxx]
- RXATTN [ON or OFF]
- RXLEVEL [–20 to 0]
- RXTOL [NORMAL or CUSTOM]
- RXTOT [NONE, 1-1440]
- SAVECONFIG
- SCD [0-255]
- SER
- SHOW [DC, PWR]
- SNR
- SPECTRUM [xxx.xx]
- SQUELCH [AUTO, BYPASSED]
- SREV
- STAT
- SWC [ON, OFF]
- TFTP
- TEMP
- TOT [1-255, ON, OFF]
- TX [xxx.xxxx]
- TXLEVEL [–20 to 0, AUTO]
- UNIT [10000...65000]
- UPTIME
- VERSION
- 7.0 TROUBLESHOOTING
- 8.0 TECHNICAL REFERENCE
- 8.1 Technical Specifications
- 8.2 Performing Network-Wide Remote Diagnostics
- 8.3 User-Programmable I/O Functions - Pending
- 8.4 Analog Operation of the Transceiver
- Physical Interface
- Operational Characteristics
- Web Method
- TFTP Method
- Serial Transfer Method
- Error Messages During File Transfers
- 9.0 GLOSSARY OF TERMS
MDS 05-4670A01, Rev. E SD Series Reference Manual (x710 Mode) 29
NOTE: The radio is configured by default to be in DLINK mode. The
COM1
port automatically determines the connected baud rate
(within the range of 1200–115200 bps). Enter a series of
Return Key presses about a half second apart until the
>
prompt
appears. This indicates that the radio is ready to receive
commands.
DTYPE [NODE/ROOT]
Unit’s Diagnostics
Type
This command establishes the local radio as a root radio or node radio
for network-wide diagnostics. Entering
DTYPE NODE
configures the
radio as a node radio. Entering
DTYPE ROOT
configures the radio as a root
radio. Entering the
DTYPE
command alone displays the current setting.
DUMP
Read Current Unit
Profile
This command causes all of the programmed settings to be displayed.
EMP [ON/OFF]
Modem TX Audio
Pre-Emphasis
This command displays or sets the TX pre-emphasis and RX
De-Emphasis when the radio is operating with the analog mode and the
radio’s MODEM is turned off (
MODEM NONE
). It should be set to match
the other radios in the system. The use of pre- and de-emphasis can help
reduce the detrimental influence of high frequency audio noise.
ETHADDR
Ethernet Address
Displays programmed Ethernet MAC address (set at the factory).
FORCEALARM [ON or OFF]
Force Alarm
Generates a test alarm for 10 sec. Use to test alarm outputs and
switch-over in redundant systems.
FORCEDCD [ON or OFF]
Force DCD
Forces Data Carrier Detect (DCD) to always be asserted. Use when con-
necting to equipment that requires a constant DCD indication.
HELP
User Help
Show available commands.