User Manual
Table Of Contents
- Copyright and Trademark
- RF Safety Notice (English and French)
- FCC Part 15 Notice
- Industry Canada Notice
- 1.0 INTRODUCTION
- 2.0 PRODUCT DESCRIPTION
- 3.0 APPLICATIONS
- 4.0 INSTALLATION PLANNING
- 5.0 STEP-BY-STEP INSTALLATION
- 6.0 TRANSCEIVER MANAGEMENT
- 6.1 Software Commands
- Entering Commands
- AK
- ALARM
- AMASK [0000 0000–FFFF FFFF]
- ASENSE [HI, LO]
- AUDIO [ON, OFF]
- BAUD [xxxxx abc]
- BIN [DATA, CLEAR]
- BOOT
- BUFF [ON, OFF]
- CKEY [ON–OFF]
- CTS [0–255]
- CTSHOLD [0–60000]
- DATAKEY [ON, OFF]
- DEV
- DEVICE [DCE, CTS KEY]
- DKEY
- DLINK [ON/OFF/xxxx]
- DTYPE [NODE/ROOT]
- DUMP
- EMP [ON/OFF]
- ETHADDR
- FORCEALARM [ON or OFF]
- FORCEDCD [ON or OFF]
- HELP
- INIT
- INIT [SDx]
- INIT [P-20]
- IPCONFIG
- KEY
- MENU
- MODEL1
- MODEL2
- MODEM [xxxx]
- OWM [XXX...]
- OWN [XXX...]
- PORT [RS232, RS485]
- PTT [0–255]
- PTTSIG [OFF, LOW, HI]
- PWR [20–37]
- RESTORECONFIG
- RESTOREDEFAULTS
- RMODE [X710, TRANSPARENT, PACKET, CMAC, HELP]
- RSSI
- RTSKEY [ON, OFF]
- RTU [ON/OFF/0-80]
- RX [xxx.xxxx]
- RXATTN [ON or OFF]
- RXLEVEL [–20 to 0]
- RXTOL [NORMAL or CUSTOM]
- RXTOT [NONE, 1-1440]
- SAVECONFIG
- SCD [0-255]
- SER
- SHOW [DC, PWR]
- SNR
- SPECTRUM [xxx.xx]
- SQUELCH [AUTO, BYPASSED]
- SREV
- STAT
- SWC [ON, OFF]
- TFTP
- TEMP
- TOT [1-255, ON, OFF]
- TX [xxx.xxxx]
- TXLEVEL [–20 to 0, AUTO]
- UNIT [10000...65000]
- UPTIME
- VERSION
- 7.0 TROUBLESHOOTING
- 8.0 TECHNICAL REFERENCE
- 8.1 Technical Specifications
- 8.2 Performing Network-Wide Remote Diagnostics
- 8.3 User-Programmable I/O Functions - Pending
- 8.4 Analog Operation of the Transceiver
- Physical Interface
- Operational Characteristics
- Web Method
- TFTP Method
- Serial Transfer Method
- Error Messages During File Transfers
- 9.0 GLOSSARY OF TERMS
22 SD Series Reference Manual (x710 Mode) MDS 05-4670A01, Rev. E
ASENSE [HI, LO] Details
Page 25
Set/display the state of the alarm output signal to
ACTIVE HI or ACTIVE LO.
AUDIO [ON, OFF] Details
Page 26
Set/display the receive audio monitor mode for
modems.
BAUD [xxxxx abc] Details
Page 26
Set/display the DATA INTERFACE data rate and
format.
BIN [DATA, CLEAR]
Details Page 26
Display or clear data counters.
BOOT Details Page 26 Used to initiate a software reboot.
BUFF [ON, OFF] Details
Page 26
Enables or disables the internal radio data buffer.
CKEY [ON–OFF] Details
Page 27
Enables or disables the continuously keyed
mode. Note: Remotes cannot receive when
keyed.
CTS [0–255] Details Page
27
Set/display the Clear-to-Send delay in seconds.
CTSHOLD [0–60000]
Details Page 27
Set/display Clear-to-Send hold delay.
DATAKEY [ON, OFF]
Details Page 28
Enables or Disables key-on-data mode
(ON = key-on-data or RTS, OFF = key-on-RTS).
DEV Details Page 28 Set/display modem control deviation.
DEVICE [DCE, CTS KEY]
Details Page 28
Set/display device mode.
DKEY Details Page 28 Dekey the radio (transmitter OFF). This is
generally a radio test command.
DLINK [ON/OFF/xxxx]
Details Page 28
Configures local diagnostic link protocol.
DTYPE [NODE/ROOT]
Details Page 29
(diagnostics) Sets up a radio as a root or node
radio.
DUMP Details Page 29 Display all programmable settings.
EMP [ON/OFF] Details
Page 29
Set/display TX audio pre-emphasis for analog
mode.
ETHADDR Details Page 29 Displays Ethernet MAC address
(non-configurable).
FORCEALARM [ON or
OFF] Details Page 29
Generates a test alarm for 10 sec.
FORCEDCD [ON or OFF]
Details Page 29
Forces Data Carrier Detect (DCD) to always be
asserted.
HELP Details Page 29 Shows available commands.
INIT Details Page 30 Set radio parameters to factory defaults for the
radio outside the P-20 Protected Network
Chassis.
INIT [SDx] Details Page 30 Configure radio for use outside of the Protected
Network Chassis (SDxP). Restores certain
transceiver defaults changed by the INIT P-20
command.
Table 11. Command Summary (Continued)
Command name Function