User Manual
Table Of Contents
- Copyright and Trademark
- RF Safety Notice (English and French)
- FCC Part 15 Notice
- Industry Canada Notice
- 1.0 INTRODUCTION
- 2.0 PRODUCT DESCRIPTION
- 3.0 APPLICATIONS
- 4.0 INSTALLATION PLANNING
- 5.0 STEP-BY-STEP INSTALLATION
- 6.0 TRANSCEIVER MANAGEMENT
- 6.1 Software Commands
- Entering Commands
- AK
- ALARM
- AMASK [0000 0000–FFFF FFFF]
- ASENSE [HI, LO]
- AUDIO [ON, OFF]
- BAUD [xxxxx abc]
- BIN [DATA, CLEAR]
- BOOT
- BUFF [ON, OFF]
- CKEY [ON–OFF]
- CTS [0–255]
- CTSHOLD [0–60000]
- DATAKEY [ON, OFF]
- DEV
- DEVICE [DCE, CTS KEY]
- DKEY
- DLINK [ON/OFF/xxxx]
- DTYPE [NODE/ROOT]
- DUMP
- EMP [ON/OFF]
- ETHADDR
- FORCEALARM [ON or OFF]
- FORCEDCD [ON or OFF]
- HELP
- INIT
- INIT [SDx]
- INIT [P-20]
- IPCONFIG
- KEY
- MENU
- MODEL1
- MODEL2
- MODEM [xxxx]
- OWM [XXX...]
- OWN [XXX...]
- PORT [RS232, RS485]
- PTT [0–255]
- PTTSIG [OFF, LOW, HI]
- PWR [20–37]
- RESTORECONFIG
- RESTOREDEFAULTS
- RMODE [X710, TRANSPARENT, PACKET, CMAC, HELP]
- RSSI
- RTSKEY [ON, OFF]
- RTU [ON/OFF/0-80]
- RX [xxx.xxxx]
- RXATTN [ON or OFF]
- RXLEVEL [–20 to 0]
- RXTOL [NORMAL or CUSTOM]
- RXTOT [NONE, 1-1440]
- SAVECONFIG
- SCD [0-255]
- SER
- SHOW [DC, PWR]
- SNR
- SPECTRUM [xxx.xx]
- SQUELCH [AUTO, BYPASSED]
- SREV
- STAT
- SWC [ON, OFF]
- TFTP
- TEMP
- TOT [1-255, ON, OFF]
- TX [xxx.xxxx]
- TXLEVEL [–20 to 0, AUTO]
- UNIT [10000...65000]
- UPTIME
- VERSION
- 7.0 TROUBLESHOOTING
- 8.0 TECHNICAL REFERENCE
- 8.1 Technical Specifications
- 8.2 Performing Network-Wide Remote Diagnostics
- 8.3 User-Programmable I/O Functions - Pending
- 8.4 Analog Operation of the Transceiver
- Physical Interface
- Operational Characteristics
- Web Method
- TFTP Method
- Serial Transfer Method
- Error Messages During File Transfers
- 9.0 GLOSSARY OF TERMS
MDS 05-4670A01, Rev. E SD Series Reference Manual (x710 Mode) 23
INIT [P-20] Details Page 30 Configure radio for service within a P-20
Protected Network Chassis.
IPCONFIG Details Page 31 Ethernet interface configuration.
KEY Details Page 31 Key the radio (transmitter ON). This is generally a
radio test command.
MENU Details Page 31 Activates the radio’s menu-based program (if
supported).
MODEL1 Details Page 31 Shows configuration order entry string associated
with the radio. Programmed at the factory.
MODEL2 Details Page 31 Shows an identifier string associated with the
radio’s hardware bill of materials and revision.
Programmed at the factory.
MODEM [xxxx] Details
Page 31
Set the modem characteristics of the radio.
OWM [XXX...] Details Page
33
Set/display the owner’s message.
OWN [XXX...] Details Page
33
Set/display the owner’s name.
PORT [RS232, RS485]
Details Page 34
Set/display COM2 data port interface settings.
PTT [0–255] Details Page
34
Set/display the Push-to-Talk delay in
milliseconds.
PTTSIG [OFF, LOW, HI]
Details Page 34
Set/display push-to-talk configuration.
PWR [20–37] Details Page
34
Set/display the transmit power setting.
RESTORECONFIG Details
Page 34
Restores a saved user configuration.
RESTOREDEFAULTS
Details Page 34
This command restores the original factory
configuration.
RMODE [X710,
TRANSPARENT,
PACKET, CMAC, HELP]
Details Page 34
Allows the reconfiguration of the SD operating
mode.
RSSI Details Page 34 Display the Received Signal Strength Indication.
RTSKEY [ON, OFF] Details
Page 35
Set/display how the radio responds to RTS
keying. Default is RTSKEY OFF, to prevent
undesired keying of the transmitter when RTS is
raised by a terminal program.
RTU [ON/OFF/0-80] Details
Page 35
Re-enables or disables the radio’s internal RTU
simulator and sets the RTU address.
RX [xxx.xxxx] Details
Page 35
Set/display receiver frequency.
RXATTN [ON or OFF]
Details Page 35
Enables or disables receive attenuation.
RXLEVEL [–20 to 0]
Details Page 35
Set/display the receive audio input level.
Table 11. Command Summary (Continued)
Command name Function