Installation Instructions If you have questions, call 800.GE.CARES or visit our website at: www.monogram.
Safety Information READ AND SAVE THESE INSTRUCTIONS BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT ³ Save these instructions for local inspector’s use. • IMPORTANT ³ Observe all governing codes and ordinances. • Note to Installer ³ Be sure to leave these instructions with the Consumer. • Note to Consumer ³ Keep these instructions with your Owner’s Manual for future reference. • Skill Level ³ Installation of this appliance requires basic mechanical and electrical skills.
Consignes de Sécurité LISEZ ET CONSERVEZ CES INSTRUCTIONS AVANT DE COMMENCER Lisez ces instructions entièrement et attentivement. IMPORTANT • ³ Conservez ces instructions pour l’inspecteur électrique local. • IMPORTANT ³ Respectez tous les codes et règlements en vigueur. • Remarque pour l’installateur – Assurez–vous de remettre ces instructions à l’utilisateur. • Remarque pour l’Utilisateur – Conservez ces instructions avec votre notice d’utilisation pour toute référence future.
Installation Instructions CONTENTS Product Dimensions .............................................................................. 4 Installation Clearances ........................................................................5 Optional Duct Cover Accessories ....................................................5 Installation Height, Duct Cover Accessories..............................6 Advance Planning .................................................................................. 7 Power Supply ...
Advance Planning INSTALLATION CLEARANCES These vent hoods are designed to be installed onto a wall RU EHQHDWK D VRI¿W RU FDELQHW Installation with Warming Shelf • Hoods must be installed 32" min., 38" max. over any type cooking surfac when warming shelf is used. Installation without Warming Shelf • Install these hoods 30" min. to 36" max. above the cooking surface when installed over any professional style cooktop or range. • These hoods may be installed 24" min.
Advance Planning DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES These vent hoods must be installed 30" min. to 36" max. above the standard 36" high cooking surface. When installed with the warming shelf, allow 32" min. to 38" max. clearance. The exact hood installation height is determined by the ceiling height. Measure the exact ceiling height. Review the chart at right to determine the range of possible hood installation heights that can be accomplished with one or more duct covers. 3.
Advance Planning ADVANCE PLANNING Ductwork Planning • These vent hoods are equipped for 10" round ductwork. For best performance, use 10" round ductwork on the 48" wide hoods. 30" and 36" hoods may be transitioned to 8" round. • This hood may be vented vertically through upper FDELQHWV VRI¿W RU FHLOLQJ $ GXFW WUDQVLWLRQ SLHFH LV supplied for vertical exhaust. Use locally supplied elbows to vent horizontally through the rear wall. • Determine the exact location of the vent hood.
Advance Planning DUCT FITTINGS Use this chart to compute maximum permissable lengths for duct runs to outdoors. Equivalent Length* Duct Piece 10" round to 8" round 5 ft. Round, straight 1 ft. (per foot length) Maximum recommended duct OHQJWK IRU WKHVH KRRGV IHHW 90° elbow 8" Dia. 17 ft. 10" Dia. 24 ft.
Installation Preparation REMOVE THE PACKAGING • Remove packages from the "V" shaped cardboard section. Remove shipping pads. • Lift the hood out of the box. IMPORTANT: Duct Transition Wood Mounting Support Hood Lift the hood by grasping the outside edges of the exhaust opening on the top. Motor Mounted on Skid Shipping Carton • The vent hood motor is shipped secured to the skid with 4 screws. Locate and remove 2 screws on each side of the motor. Discard the shipping skid and screws.
Installation Instructions 67(3 '(7(50,1( +22' '8&7:25. $1' :,5,1* /2&$7,216 • Use a level to draw the cooktop centerline location. Draw the line to ceiling height. • Measure desired distance from the bottom of the hood to the cooking surface. 9-7/8" Top of Hood Note: If you are installing the hood with duct covers, be sure to read “Using Duct Cover Accessories” page 7. Exact installation height may be determined by use of one or more duct covers.
Installation Instructions 67(3 $ ,167$// +22' 2172 :$// SKIP THIS STEP IF INSTALLING BENEATH A SOFFIT OR CABINET, *2 72 67(3 % IMPORTANT: Framing must be capable of VXSSRUWLQJ XS WR OEV Install Transition Onto Top of Hood • Locate at least 2 vertical studs at the wood support. • Center the supplied wood support, left to right and below the 20" marked line. Duct Transition IMPORTANT: Remove shipping tape from damper and check that damper moves freely.
Installation Instructions 67(3 % $OWHUQDWH 0RXQWLQJ 0HWKRG INSTALL HOOD TO SOFFIT OR BENEATH CABINETS SKIP THIS STEP IF USING WALL MOUNTING METHOD When necessary, the hood may be installed so that it is VXSSRUWHG E\ WKH VRI¿W 7KH VRI¿W VKRXOG EH FRQVWUXFWHG ZLWK [ ·V • Determine the installation location on the wall.
Installation Instructions STEP 3 CONNECT DUCTWORK • Install ductwork, making connections in direction of DLUÀRZ DV LOOXVWUDWHG • Secure joints in ductwork with sheetmetal screws. • Wrap all duct joints with duct tape for an airtight seal. • Use duct tape to Air Flow VHDO WKH ÀDQJH Duct Tape connection. Reach Over Seam Screw inside the hood and and Screw push the damper up to be sure it moves freely.
Installation Instructions STEP 7 INSTALL FILTERS • Drop grease tray into the hood. The rear tabs should engage the slots in the hood track. ,QVHUW WKH JUHDVH ¿OWHU LQWR WKH RSHQLQJ DQG GURS LQWR WKH ERWWRP 5DLVH ¿OWHU WR WKH WRS DQG ORFN LQWR SODFH 7R UHPRYH WKH ¿OWHUV JUDVS WKH KDQGOH SXVK WKH ¿OWHU up and lift out. STEP 8 INSTALL BACKGROUND AND SHELF INSTALL BACKGUARD: • Remove packaging. • Place backguard against the bottom of the hood to use as a template.
Installation Instructions STEP 9 INSTALL SHELF "ONLY" 67(3 ,167$// ,03/(0(17 52'6 5HPRYH VKHOI SDFNDJLQJ DQG SURWHFWLYH ¿OP • If installing the shelf alone, without the backguard, place shelf against the bottom of the hood and mark the screw hole locations "B" on the wall. • Drill two 1/8" pilot holes. • If the drill did not enter the studs, enlarge holes to 3/8". • Insert the wall anchors into the enlarged holes. Remove the screws from the wall anchors.
Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram® local service in your area, call 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and VSHFL¿FDWLRQV DUH VXEMHFW WR FKDQJH ZLWKRXW QRWLFH 49-80152-7 GE Consumer & Industrial GE Appliances General Electric Company Louisville, KY 40225 02-13 GE Printed in Mexico GEAppliances.