Installation Instructions If you have questions, call 800-GE-CARES or visit our website at: www.monogram.com 36" Stainless Steel Gas Cooktops Natural Gas Model: ZGU375NS LP Gas Model ZGU375LS Monogram.
Before you begin—Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector’s use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions with your Owners Manual for future reference. WARNING This appliance must be properly grounded and with correct polarity. See “Power Supply”, page 6.
Design Information Stainless Steel G a s Cooktop ZGU375NS 36" natural gas cooktop ZGU375LS 36" LP gas cooktop For those who prefer gas heat for cooking, the Monogram built-in gas stainless steel cooktop offers the cooking method of choice. These models are factory set for either natural gas or LP gas operation. Be sure to order the correct model for the installation situation. Dimensions and clearances 13" Max. 36-1/2" 20-5/8" Deep at Center 19-3/4" * 2-15/16" Min.
Design Information Stainless Steel G a s Cooktop Advance planning installation options Tools and Materials Required 4 Cooktop and ZVB36 Downdraft Vent Combination Installation. See page 9. These cooktops may be installed with a 36" Monogram Downdraft Vent, models ZVB36. See page 9 for cutout and clearances. –The countertop must have a deep flat surface to accommodate the combined installation of the cooktop and vent. –The downdraft vent with blower, motor and ductwork will occupy the base cabinet.
Installation Preparation Stainless Steel G a s Cooktop Cut the Opening 11-9/16" Min. Cutout To Side Wall 11-9/16" Min. to Side Wall 3-3/8" Min. to Rear Vertical Combustibles 18-7/8" 35-5/16" 2-3/4" Min. From Front of Countertop CAUTION: Wallcoverings, countertops and cabinets should withstand 200°F heat generated by the cooktop. Measure carefully when cutting countertop. Make sure sides of opening are parallel and rear and front cuts are exactly perpendicular to sides.
Installation Preparation Stainless Steel G a s Cooktop Power supply locations Gas supply: These cooktops are shipped from the factory set for either natural gas or LP gas. Check to be sure you have the correct cooktop for the type of gas being used. • The pressure regulator must be connected in series with the manifold of the cooktop and must remain in series with the supply line regardless of type of gas being used. • The natural gas model is designed to operate at 5" water column pressure.
Installation Stainless Steel G a s Cooktop 1 Step Install Cooktop 2 Step Install Pressure Regulator • Remove packaging from the cooktop. • Position the cooktop over the opening, making sure that the power cord is dropped into the cabinet. • Lower the cooktop into the cutout, pressing gently and evenly to seat. • Thumbscrew brackets are located on the right and left sides of the cooktop. • Turn thumbscrews to touch the underside of the countertop until just finger tight. Do not overtighten.
Installation Stainless Steel G a s Cooktop 3 • Check to be sure the receptacle is properly wired by checking for proper polarity and grounding. • Plug in power cord. 4 • Remove tape on burners. • Assemble burner as shown. Check to be sure that burner heads and caps are securely seated. Pin(s) must completely engage holes to ensure proper assembly. Step Connect electrical Step Assemble burners, check ignition • Check for proper ignition: –Push in one control knob and turn 90° to HIGH position.
Installation Options Installation With Downdraft Vent Stainless Steel G a s Cooktop Cooktop Installation with a 36" Monogram Downdraft Vent, models ZVB36. The installation of the downdraft vent with this cooktop requires careful consideration. Both the cooktop and the vent must be installed according to each specific installation instruction. For accurate planning, review the Downdraft Vent Installation Instructions in advance, order Pub. No. 49-80185.
Installation Options Installation With Warming Drawer Stainless Steel G a s Cooktop Cooktop Installation Over a 30" Monogram Warming Drawer, models ZTD910. These cooktops may be installed over a 30" Warming Drawer. Both the cooktop and the warming drawer must be installed according to each specific installation instruction. For accurate planning, review the Warming Drawer Installation Instructions in advance, order Pub. No. 49-8937.
Installation Options Installation With Single Oven Stainless Steel G a s Cooktop Cooktop Installation Over a 30" Monogram Single Oven, models ZET1038. These cooktops may be installed over the Monogram ZET1038 single oven. Both the cooktop and the oven must be installed according to each specific installation instruction. For accurate planning, review the 30" Oven Installation Instructions in advance, order Pub. No. 49-80188. –Allow 6" Min.
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram® local service in your area, call 1-800-444-1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub. No. 49-80218-1 Dwg. No.