Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.com ZIC360N RH, ZIC360N LH, ZICS360N RH, ZICS360N LH Built-In Bottom-Freezer Refrigerators Design Guide With Installation Instructions Monogram. ® We bring good things to life.
Safety Information Skill Level - Installation of this refrigerator requires BEFORE YOU BEGIN basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner’s Manual for warranty information. Read these instructions completely and carefully. • IMPORTANT - Save these instructions for local inspector’s use. Observe all governing codes and ordinances.
Design Guide THE INSTALLATION SPACE DIMENSIONS AND CLEARANCES 35" Case Width The finished cutout width must be 35-1/2". 35-1/2" Finished Width Wall View 2-5/16" *84" 7" 10" 84-1/2" max 83-1/2" min Finished Opening Electrical Area 74-1/2" From Floor to Bottom of Electrical 24" Cutout Depth 5" Water Supply 3 1/2" 36" Frame to Frame Width 5" 3 1/2" Water And Electrical Locations The opening must be prepared with the electrical and water supply located as shown. * Shipping height.
Design Guide Refrigerator 23-7/8" From Rear of Refrigerator 2" 1" Case Trim 1/2" 1/4" 3" 1-3/4" 3/4" 1-1/2" 2-3/4" 2-1/2" 1-1/4" 2-1/4" 1/4" 1/2" 3/4" 1" 3/4" Overlay Panel (Nominal Size) Door 1/4" Top View 130° DOOR SWING (factory setting) Scale 1:1 4 1/2" 3/4" 1" 1-1/4"
Design Guide Refrigerator Case Trim 23-7/8" From Rear of Refrigerator 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" Door 3/4" Overlay Panel (Nominal Size) 1/4" Top View 90° DOOR SWING (optional setting) Scale 1:1 1/2" 3/4" 1" 1-1/4" 5
Design Guide CUSTOMIZATION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Models Available Stainless Steel Wrapped Models: ZICS360N RH (right-handed door) ZICS360N LH (left-handed door) Trimmed models: ZIC360N RH (right-handed door) ZIC360N LH (left-handed door) Overlay panels You may also choose to install custom overlay panels from your cabinet manufacturer. This design provides a seamless appearance which integrates smoothly with surrounding cabinetry.
Design Guide 1/4" FRAMED PANEL DIMENSIONS If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door, drawer and grille. Door/Drawer If the custom panel is less than 1/4" thick and if it fits loosely in the door frame, it can be backed up with a piece of filler material or foam tape to improve the fit.
Design Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Order the side panels from the cabinet manufacturer. The ZUG2 unified grille panel kit provides for the installation of a framed or overlay grille panel. A Grille Panel 24" B Framed Panel Dimensions * Depending on installation height.
Installation Instructions TOOLS REQUIRED MATERIALS REQUIRED • Tinsnips to cut banding • Stepladder • Bucket • Level • Appliance Hand Truck • Tubing cutter • 7/16" open-end wrench • #2 Phillips screwdriver • Drill and appropriate bits • 5/16", 7/16" socket • Safety glasses • 1-1/4" open end wrench • Pliers • 35" long 2x4 for Anti-Tip support • Copper water line tubing • Water shut-off valve (optional but recommended) • Custom panels for fresh food door, freezer drawer and grille panel • Screws to secure r
Installation Instructions • Remove the four 7/16" bolts securing the straps to the skid. STEP 1 REMOVE PACKAGING CAUTION: Refrigerator is much heavier at the CAUTION: top than at the bottom – be careful when moving. When using a hand truck, handle from side only. DO NOT ATTEMPT TO ROLL UNIT OFF SKID. PRUDENCE: Toekick Le réfrigérateur est beaucoup plus lourd en haut qu'en bas. Il faut être prudent lors des déplacements.
Installation Instructions STEP 4 INSTALL ANTI-TIP BRACKETS STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM WARNING: ANTI-TIP PRECAUTIONS The refrigerator is top-heavy and must be secured to prevent the possibility of tipping forward. Skip this step when not using an RO System If the water supply to the refrigerator is from a Reverse Osmosis Water System use the refrigerator’s filter bypass plug.
Installation Instructions STEP 6 SECURE REFRIGERATOR TO CABINETRY STEP 5 LEVEL REFRIGERATOR All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator. • To level the back of the refrigerator, turn the 7/16" hex nut located above the front wheels. Turn clockwise to raise or counterclockwise to lower the refrigerator. • For front leveling, use a 1-1/4" open-end wrench.
Installation Instructions STEP 7 ADJUST DOOR SWING STEP 8 INSTALL GRILLE PANEL NOTE: This refrigerator has a 2-position door stop. When space does not allow the door to swing open fully to 130°, you may change the door swing to a 90° opening. Skip this step if door opening is satisfactory for your installation situation. • Raise the grill panel to stop position. Raise Grille Panel Loosen Side Trim Screw • Lift the grille panel to access the wire cover trim.
Installation Instructions STEP 9 INSTALL FRAMED PANELS Right hand models shown. Use the same instructions for left hand models. IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 9A. Handle Trim Door Trim Refrigerator Door Use Front Holes to Secure Trim Use Rear Holes to Secure Handle Standard supplied handle shown in 1/4" panel position. Install door and drawer panels: • Open door to 90°. Remove the 4 Phillips head screws from the door handle. • Remove handle. Retain all screws.
Installation Instructions STEP 9A INSTALL OVERLAY PANELS Right hand models shown. Use the same instructions for left hand models. Door Trim Handle Trim Refrigerator Door Move Forward For 3/4" Panel Use Front Holes to Secure Handle Use Rear Holes to Secure Trim Supplied handle shown in the overlay panel position. Install door and drawer panels: • Open door to 90°. Remove the 4 Phillips head screws from the door handle. • Remove handle. Retain all screws. • Remove 4 screws holding trim, lift off trim.
Installation Instructions STEP 12 START ICEMAKER STEP 10 CONNECT WATER SUPPLY Check to be sure that refrigerator power cord is not plugged into the wall outlet. Power Switch Feeler Arm House Water Supply • Flip the switch to I (ON). The icemaker will begin operation automatically. • Be sure nothing interferes with the sweep of the feeler arm. • Discard the first full bucket of ice cubes. • To turn the icemaker off, set the switch to O (OFF).
Notes 17
Notes 18
Notes 19
Note: While performing installations described in this book, safety glasses or goggles should be worn. TM For Monogram local service in your area, call 1-800-444-1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. ® Monogram. General Electric Company Louisville, KY 40225 Pub. No. 49-60136 Dwg. No. 164D4371P001 (N.D.
