DL 1a3e143d8cd68da04d3debb26c99

Product Specification Revised 1/18
NOTES
MONOGRAM
®
30" WARMING DRAWER ZW9000SJSS
A
If you are installing in
frameless cabinets, it
may be necessary to
install 1/2" wide cleats to
accept drawer mounting
screws. See drawer
for mounting screw
locations.
B
Install a 2"x2" or 2"x4"
anti-tip block against
rear wall, 9" from floor
of cutout to bottom of
block. The anti-tip block
must be installed to
prevent the drawer from
tipping forward when
opened and loaded.
Failure to add the anti-
tip block could result in
personal injury.
C
When installing the
warming drawer below
a cabinet drawer, a
solid barrier must be
installed at least above
the warming drawer
to block access. Use
any solid material such
as 1/4" thick plywood.
Allow at least 1/4"
air gap between the
barrier and the top of
the warming drawer.
Observe the 5" min.
above the floor or 1"
min. above the toe kick
installation height.
D
When installing two
warming drawers side
by side, install them in
separate cut-outs and
allow a 2" min. gap
between each cut-out.
E
The warming drawer
may be supported by
either a solid bottom or
2"x2" or 2"x4" runners.
The support must
be level and rigidly
mounted, flush with
the bottom edge of the
cut-out (there is no way
to level the drawer once
it has been installed,
so make sure that the
supports are level). The
floor or runners must be
capable of supporting at
least 150 lbs.
For more details refer to
the installation instructions
for this product.
INSTALLATION BELOW A CABINET DRAWER
PROVIDING CABINET SUPPORT INSTALLING ANTI-TIP BLOCKS
SIDE BY SIDE INSTALLATION
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZDT910SFSS
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZDT910SFSS
SIDE VIEW
FRONT VIEW
TOP VIEW
28 1/2" (72.4)
min. cutout width
23 1/2" (59.7)
min. cutout width
1/4"
(.6)
min.
1"
(2.5)
min.
Above
toe-kick
2" (5.1) min.
Between cut-outs
2" (5.1) x 4" (10.2)
or Equivalent Runners
Install
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Anti-tip Block against
rear cabinet wall 9" from
floor to bottom of block
Side cleats
9 1/4"
(23.5)
Cut-out
height
30" (76.2)
25" (63.5)
23 1/2"
(59.7)
2" (5.1) x 4" (10.2)
or
2" (5.1) x 2" (5.1)
Runners or Solid Bottom
ZDT910SFSS
A
A
D
E
B
B
C