Installation Instructions Over the Range Microwave Oven PVM9005 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com BEFORE YOU BEGIN Read these instructions completely and carefully. • • IMPORTANT – Save these instructions for local inspector’s use. IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the consumer. Throughout this manual, features and appearance may vary from your model.
Installation Instructions CONTENTS General information C Outside Back Exhaust .......................... 21-24 Installation Overview.......................... 21 Important Safety Instructions .............................. 3 Preparing Rear Wall for Outside Back Exhaust ........................ 21 Electrical Requirements........................................ 3 Attach Mounting Plate to Wall ......21, 22 Tools You Will Need .............................................. 4 Preparation of Top Cabinet ..
Installation Instructions This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as: DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Installation Instructions TOOLS YOU WILL NEED #1 and #2 Phillips screwdriver Pencil Carpenter square (optional) Ruler or tape measure and straight edge Tin snips (for cutting damper, if required) Scissors (to cut template, if necessary) Electric drill with » s, » s, 1»2s and 5»8s drill bits 3 16 Gloves Safety goggles 4 7 16 Saw (saber, hole or keyhole) Level Stud finder Hammer (optional) Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet ins
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 11. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. EQUIVALENT LENGTH x NUMBER USED = LENGTH Roof Cap 24 Ft. x (1) = 24 Ft. 12 Ft. Straight Duct (6s Round) 12 Ft. x (1) = 12 Ft. x (1) = 5 Ft. = 41 Ft.
Installation Instructions NOTE: If you need to install ducts, note that the total duct length of 31»4Ǝ [ Ǝ UHFWDQJXODU RU Ǝ GLDPHWHU URXQG duct should not exceed 140 equivalent feet. Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. NOTE: It is important that venting be installed using the most direct route and with as few elbows as possible. This ensures clear venting of exhaust and helps prevent blockages.
Installation Instructions DAMAGE – SHIPMENT INSTALLATION • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.
Installation Instructions MOUNTING SPACE Ǝ PD[ 16-1»4Ǝ Ǝ 2Ǝ Ǝ RU PRUH from the floor to the top of the oven 8 Ǝ min. Bottom edge of cabinet needs WR EH Ǝ RU more from the cooking surface Backsplash NOTES: • 7KH VSDFH EHWZHHQ WKH FDELQHWV PXVW EH Ǝ wide and free of obstructions. • This oven is for installation over ranges up to Ǝ ZLGH • If you are going to vent your oven to the outside, see Hood Exhaust Section for exhaust duct preparation.
Installation Instructions PLACEMENT OF THE MOUNTING PLATE 1 A REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE B FINDING THE WALL STUDS 1 Open the box and fold back all four carton flaps fully against the carton sides. Remove the following items from the protective foam: installation instructions, filters, exhaust adaptor, damper, and the small hardware bag. Do not remove the foam protecting the front of the microwave oven.
Installation Instructions C DETERMINING MOUNTING PLATE LOCATION UNDER YOUR CABINET Plate Position – flat bottom cabinet Mounting Plate Tabs Touching the Cabinet Bottom Plate Position – recessed cabinet bottom Mounting Plate Tabs Touching the Back Frame of the Cabinet Ǝ WR &RRNWRS $W OHDVW Ǝ XS WR Ǝ Plate Position – cabinet with front overhang Mounting Plate with Tabs Below Cabinet Bottom the Same Distance as the Front Overhang Depth Your cabinets may have decorative trim that interferes with t
Installation Instructions D ALIGNING THE MOUNTING PLATE 30” Hole B Draw a Vertical Line on Wall from Center of Top Cabinet Hole A Hole D Hole C Area E CAUTION Wear gloves to avoid cutting fingers on sharp edges. 1 Draw a vertical line on the wall at the center of the 30s wide space. 2 Use the mounting plate as the template for the rear wall.
Installation Instructions 2 INSTALLATION TYPES This microwave oven is designed for adaptation to the following 3 types of ventilation: A. Recirculating (Non-Vented Ductless) B. Outside Top Exhaust (Vertical Duct) C. Outside Back Exhaust (Horizontal Duct) A RECIRCULATING (NON-VENTED DUCTLESS) (Choose A, B or C) NOTE: Select the type of ventilation required for your installation and proceed to that section.
Installation Instructions A RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW A1. A2. A3. A4. A5. A6. Attach Mounting Plate to Wall Prepare Top Cabinet Adjust Blower Motor Install Charcoal Filter Mount the microwave oven Installing/Replacing the Charcoal Filter Without Access to Top Screws and the Unit Has Already Been Mounted. A1 ATTACH THE MOUNTING PLATE TO THE WALL 3 Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
Installation Instructions A3 ADJUST BLOWER MOTOR 1 Remove the screws holding the blower unit and the screws securing the blower plate. Remove the blower plate from the outer case by sliding it toward the back of the microwave and pulling up. Blower Motor Screws A3 ADJUST BLOWER MOTOR (cont.) Fan Blades Wires Blower Plate Back of Mircrowave 3 Roll the blower so that fan blade openings are facing the top of the oven. Place the blower back into the opening.
Installation Instructions A4 INSTALLING THE CHARCOAL FILTER A5 MOUNT THE MICROWAVE OVEN 1 Open the door. 2 Push the “Push” area on charcoal filter cover at center of the grille. CAUTION To avoid the risk of personal injury (back injury or other injuries due to excessive weight of the microwave) or property damage, you will need two people to install this microwave. IMPORTANT: Do not grip or use handle during installation. WARNING Risk of Electric Shock.
Installation Instructions A5 MOUNT THE MICROWAVE OVEN (cont.) 1 1 3 Insert 3 self-aligning screws ( »4Ǝ [ »4”) through outer top cabinet holes. Turn two full turns on each screw. Cabinet Front Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess This distance can NOT exceed 2” to ensure proper installation Self-Aligning Screw Microwave Oven Top Self-Aligning Screws 4 Tighten the three screws to the top of the microwave oven.
Installation Instructions B OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW B1. B2. B3. B4. B5. B6. Attach Mounting Plate to Wall Prepare Top Cabinet Adjust Blower Motor Install Exhaust Adaptor Mount Microwave Oven Connect Ductwork B1 ATTACH THE MOUNTING PLATE To use toggle bolts: TO THE WALL B A Spacing for Toggles More Than Wall Thickness Mounting Plate Toggle Wings Toggle Bolt Wall Mounting Plate C D Attach the plate to the wall using toggle bolts.
Installation Instructions B2 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. B3 ADJUST BLOWER MOTOR (cont.) Rotate 90° Back of Mircrowave 3 Roll the blower so that fan blade openings are facing the top of the oven. Place the blower back into the opening. Fan Blades • Read the instructions on the TOP CABINET TEMPLATE.
Installation Instructions B4 ASSEMBLE AND INSTALL ADAPTOR Blower Plate B5 MOUNT THE MICROWAVE OVEN Damper CAUTION To avoid the risk of personal 1 Place the microwave oven in its upright position, with the top of the unit facing up and the front of the unit facing toward you. 2 Remove the screw on the back side of the blower plate and raise the blower plate off of the microwave. 3 Slide the damper from left to right into the tabs on the blower plate.
Installation Instructions B5 MOUNT THE MICROWAVE OVEN B6 CONNECTING DUCTWORK (cont.) 3 Insert a self-aligning screw through top-center cabinet hole. Temporarily secure the microwave oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Insert 2 self-aligning screws (1»4Ǝ [ 2 1»4Ǝ) through outer top cabinet holes. Turn two full turns on each screw. House Duct 1 Extend the house duct down to connect to the exhaust adaptor.
Installation Instructions OUTSIDE BACK EXHAUST (Horizontal Duct) C INSTALLATION OVERVIEW C1. C2. C3. C4. C5. Prepare Rear Wall Attach Mounting Plate to Wall Prepare Top Cabinet Adjust Blower Mount the Microwave Oven C1 PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST C2 ATTACH THE MOUNTING PLATE TO THE WALL You need to cut an opening in the rear wall for outside exhaust. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud.
Installation Instructions C2 ATTACH THE MOUNTING PLATE TO THE WALL (cont.) To use toggle bolts: Mounting Plate Spacing for Toggles More Than Wall Thickness Toggle Wings Toggle Bolt C4 ADAPTING BLOWER FOR OUTSIDE BACK EXHAUST 1 Remove the blower motor screws that holds the blower plate to the microwave oven. Slide the plate toward the back of the microwave and lift up to remove.
Installation Instructions C4 ADAPTING BLOWER FOR OUTSIDE BACK EXHAUST (cont.) C5 MOUNT THE MICROWAVE OVEN 6 Gently place the fan back into the cavity with the exhaust portion of the fan at the top and facing the back of the unit. CAUTION To avoid the risk of personal injury (back injury or other injuries due to excessive weight of the microwave) or property damage, you will need two people to install this microwave. Note: Make sure the wires remain routed through the openings in the motor frame.
Installation Instructions C5 MOUNT THE MICROWAVE OVEN (cont.) 3 Insert a self-aligning screw through top-center cabinet hole. Temporarily secure the microwave oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.) Insert 2 self-aligning screws (1»4Ǝ [ 2 1»4Ǝ) through outer top cabinet holes. Turn two full turns on each screw.
Installation Instructions BEFORE YOU USE YOUR MICROWAVE OVEN 1 Make sure the microwave oven has been installed according to instructions. 6 Read the Quick Use & Care. QUICK RE USE & CA 2 Remove all packing material from the microwave oven. 3 Install turntable and turntable ring in cavity. 4 Replace house fuse or turn breaker back on. 5 120 V Models: Plug power cord into a dedicated 15- to 20-amp electrical outlet. 7 KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR’S USE.
Installation Instructions Printed in China 26 49-40755 Rev.
Instrucciones de Instalación Horno microondas para colocar encima de la estufa PVM9005 ¿Preguntas? Llame a 800.GE.CARES (800.432.2737) o visite nuestro sitio web en: GEAppliances.com ANTES DE COMENZAR Lea estas instrucciones en su totalidad y atentamente. • • • IMPORTANTE – Conserve estas instrucciones para uso del inspector local. IMPORTANTE – Cumpla con todos los códigos y ordenanzas gubernamentales. Nota para el Instalador – Asegúrese de entregar estas instrucciones la Consumidor.
Instrucciones de Instalación CONTENIDOS Información General C Escape de Salida Trasero .................... 21-24 Visión General de la Instalación ......... 21 Instrucciones Importantes de Seguridad............ 3 Preparación de la Pared Trasera para el Escape de Salida Trasero ...... 21 Requisitos Eléctricos ........................................... 3 Adjunte la Placa de Montaje a la Pared 21, 22 Herramientas Que Necesitará .............................. 4 Preparación del Gabinete Superior ....
Instrucciones de Instalación INSTRUCCIONES DE SEGURIDAD IMPORTANTES Éste es el símbolo de alerta de seguridad. El mismo alerta sobre potenciales riesgos que le pueden producir la muerte o lesiones tanto a usted como a otras personas. Todos los mensajes de seguridad estarán a continuación del símbolo de alerta de seguridad y con la palabra “PELIGRO”, “ADVERTENCIA” o “PRECAUCIÓN”.
Instrucciones de Instalación HERRAMIENTAS NECESARIAS Destornillador Phillips nº1 y nº2 Lápiz Escuadra de carpintero (opcional) Regla o cinta métrica y extremo recto Tijeras para hojalata (para cortes en reguladores, si se requiere) Tijeras (para cortar plantillas, si es necesario) Taladro eléctrico con brocas de 3/15”, 7/16”, 1/2”, y 5/8” Guantes Gafas de seguridad 4 Sierra (sable, agujero o cerradura) Nivel Detector de montantes Bloques de llenado o piezas de fragmentos de madera, si son necesar
Instrucciones de Instalación CAMPANA DE ESCAPE NOTA: Lea las siguientes dos páginas solamente si planea ventilar el escape hacia el exterior. Si por el contrario planea recircular el aire de vuelta hacia el salón, continúe en la página 30. ESCAPE SUPERIOR EXTERNO (EJEMPLO SOLAMENTE) La siguiente tabla describe un ejemplo de una posible instalación de red de conductos.
Instrucciones de Instalación NOTA: Si usted necesita instalar conductos, tenga pendiente que la longitud total del conducto rectangular de 31»4Ǝ [ Ǝ R HO FRQGXFWR UHGRQGR GH Ǝ GH GLiPHWUR no debe sobrepasar 140 pies equivalentes. La ventilación externa requiere un CONDUCTO DE CAMPANA DE ESCAPE. Lea lo siguiente cuidadosamente. NOTA: Es importante que la ventilación sea instalada usando la ruta más directa y con la menor cantidad de codos posible.
Instrucciones de Instalación PARTES INCLUIDAS DAÑO – ENVÍO/ INSTALACIÓN • Si la unidad se daña durante el envío, devuelva la unidad a la tienda donde fue comprada para su reparación o reemplazo. • Si la unidad es dañada por el cliente, la reparación o reemplazo es responsabilidad del cliente. • Si la unidad es dañada por el instalador (si no es el cliente), la reparación o reemplazo deberá ser realizado por arreglo entre el cliente y el instalador.
Instrucciones de Instalación ESPACIO DE MONTAJE Ǝ PD[ 16-1»4Ǝ Ǝ 2Ǝ Ǝ R PiV desde el piso hasta la parte superior del horno 8 El extremo del fondo del gabinete necesita estar D Ǝ R PiV Ǝ a partir de la min. superficie de la estufa Protector posterior de salpicaduras NOTAS: (O HVSDFLR HQWUH ORV JDELQHWHV GHEH VHU GH Ǝ de ancho y debe estar libre de obstrucciones. • Si el espacio entre los gabinetes es mayor de Ǝ XQ ³)LOOHU 3DQHO .
Instrucciones de Instalación COLOCACIÓN DEL PLATO DE MONTAJE 1 A RETIRO DEL HORNO MICROONDAS DE LA CAJA/ RETIRO DEL PLATO DE MONTAJE 1 Abra la caja y vuelva a doblar las cuatro lengüetas de la caja completamente contra los costados de la caja. Retire los siguientes artículos de la gomaespuma protectora: instrucciones de instalación, filtros, adaptador del escape, regulador, y la caja pequeña de piezas. No retire la gomaespuma que protegé el frente del horno microondas.
Instrucciones de Instalación C DETERMINACIÓN DE LA PLACA DE MONTAJE DEBAJO DE SU GABINETE Posición de la Placa – gabinete inferior plano Las lengüetas de la Placa de Montaje Tocan la Parte Inferior del Gabinete Por lo menos 30”, hasta 36” Posición de la Placa – gabinete con frente saliente Placa de Montaje con Lengüetas Debajo de la Parte Inferior del Gabinete a la Misma Distancia que la Profunidad del Frente Saliente Posición de la Placa – gabinete inferior hueco Las Lengüetas de la Placa de Montaje To
Instrucciones de Instalación D ALINEE LA PLACA DE MONTAJE 30” Hole B Dibuje una Línea Vertical en la Pared desde el Centro a la Parte Superior del Gabinete Agujero A Agujero C Hole D Área E PRECAUCIÓN Ranura Use guantes para evitar cortes de dedos en extremos puntiagudos. 1 Dibuje una línea vertical en la pared en el centro del espacio de 30” de ancho. 2 Use la placa de montaje como plantilla para la pared trasera.
Instrucciones de Instalación 2 TIPOS DE INSTALACIÓN Este horno microondas está diseñado para ser adaptado a los siguientes 3 tipos de ventilación: A. Recirculación (Sin Conductos no Ventilados) B. Escape Exterior Superior (Conducto Vertical) C. Escape Exterior Trasero (Conducto Horizontal) A RECIRCULACIÓN (SIN CONDUCTOS NO VENTILADOS) (Elija A, B o C) NOTA: Seleccione el tipo de ventilación requerida para su instalación y proceda a dicha sección.
Instrucciones de Instalación A RECIRCULACIÓN (Sin Conductos No Ventilados) VISIÓN GENERAL DE LA INSTALACIÓN A1. ADHERA LA PLACA DE MONTAJE A LA PARED A2. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE SUPERIOR A3. AJUSTE EL MOTOR DEL CALENTADOR A4. CÓMO INSTALAR EL FILTRO DE CARBÓN A5. MONTE EL HORNO MICROONDAS A6.
Instrucciones de Instalación A3 AJUSTE EL MOTOR DEL CALENTADOR 1 Retire los tornillos que sostienen la unidad del calentador y los tornillos que aseguran el plato calentador. Retire el plato calentador de la caja externa, deslizando la misma hacia la parte trasera del horno microondas y empujando hacia arriba. A3 AJUSTE EL MOTOR DEL CALENTADOR (cont.
Instrucciones de Instalación A4 INSTALLING THE CHARCOAL FILTER A5 MONTE EL HORNO MICROONDAS 1 Abra la puerta. 2 Presione el área “Presionar” en la tapa del filtro de carbón en el centro de la parrilla. PRECAUCIÓN A fin de evitar el riesgo de lesión personal (lesión en la espalda u otras lesiones debido a un peso excesivo del horno microondas) o daños sobre la propiedad, deberá contar con la ayuda de dos personas para instalar este horno microondas.
Instrucciones de Instalación A5 MONTE EL HORNO (cont.) 3 Inserte 3 tornillos autoalineantes (1/4” – 28 x 2 ¼”) a través de los agujeros del gabinete superior externo. Dé dos giros completos a cada tornillo.
Instrucciones de Instalación B ESCAPE SUPERIOR EXTERIOR (Conducto Vertical) VISIÓN GENERAL DE LA INSTALACIÓN B1. B2. B3. B4. B5. B6.
Instrucciones de Instalación B2 USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE SUPERIOR B3 AJUSTE EL MOTOR DEL CALENTADOR (cont.) Gire 90° Es necesario que haga agujeros para los tornillos de soporte de la parte superior, un agujero lo suficientemente grande para que el cable de corriente pueda pasar, y un disyuntor lo suficientemente grande para el adaptador del escape.
Instrucciones de Instalación B4 ENSAMBLE E INSTALE EL ADAPTADOR B5 MONTE EL HORNO MICROONDAS Plato Calentador Regulador PRECAUCIÓN 1 Coloque el horno microondas en su posición vertical, con la parte superior de la unidad hacia arriba y el frente hacia usted. 2 Coloque el horno microondas en su posición vertical, con la parte superior de la unidad hacia arriba y el frente hacia usted. 3 Deslice el regulador de izquierda a derecha dentro de las lengüetas en el plato calentador.
Instrucciones de Instalación B6 CONEXIÓN DEL CONDUCTO B5 MONTE EL HORNO MICROONDAS (cont.) 3 Inserte un tornillo autoalineante a través del agujero de la parte superior del centro del gabinete. En forma temporaria asegure el horno dando al tornillo por lo menos dos giros completos una vez que las roscas fueron colocadas. (Más tarde se ajustará completamente.) Inserte 2 tornillos autoalineantes (1/4” – 28 x 2 ¼”) a través de los agujeros del gabinete superior externo. Dé dos giros completos a cada tornillo.
Instrucciones de Instalación C ESCAPE EXTERIOR TRASERO (Conducto Horizontal) VISIÓN GENERAL DE LA INSTALACIÓN C1. Prepare la Pared Trasera C2. Adjunte la Placa de Montaje a la Pared C3. Prepare el Gabinete Superior C4. Ajuste el Calentador C5. Monte el Horno Microondas C1 PREPARACIÓN DE LA PARED TRASERA PARA EL ESCAPE EXTERNO TRASERO C2 ADHIERA LA PLACA DE MONTAJE A LA PARED Es necesario cortar una abertura en la pared trasera del escape externo.
Instrucciones de Instalación C2 ADHIERA LA PLACA DE MONTAJE A LA PARED (cont.) Para usar tornillos con resorte: Placa de Montaje Espacio para Tornillos con Resorte Superior al Grosor de la Pared Tuercas Mariposa Tornillo con Resorte Pared C4 ADAPTACIÓN DEL CALEFACTOR PARA EL ESCAPE EXTERIOR TRASERO 1 Retire el tornillo del motor del calentador que sostiene el plato calentador sobre el horno microondas. Deslice el plato hacia la parte trasera del microondas y levante el mismo para retirarlo.
Instrucciones de Instalación C4 ADAPTACIÓN DEL CALEFACTOR PARA EL ESCAPE TRASERO EXTERIOR (cont.) C5 MONTE EL HORNO MICROONDAS 6 De forma suave vuelva a colocar el ventilador en la cavidad con la parte del escape del ventilador arriba y enfrentando la parte trasera de la unidad. PRECAUCIÓN NOTA: Asegúrese de que los cables permanezcan dirigidos hacia las aberturas de la estructura del motor.
Instrucciones de Instalación C5 MONTE EL HORNO MICROONDAS (cont.) 3 Inserte un tornillo autoalineante a través del agujero de la parte superior del centro del gabinete. En forma temporaria asegure el horno dando al tornillo por lo menos dos giros completos una vez que las roscas fueron colocadas. (Más tarde se ajustará completamente). Inserte 2 tornillos autoalineantes (1/4” – 28 x 2 ¼”) a través de los agujeros del gabinete superior externo. Dé dos giros completos a cada tornillo.
Instrucciones de Instalación ANTES DE USAR EL HORNO MICROONDAS Asegúrese de que el horno microondas haya sido instalado de acuerdo con las instrucciones. 1 6 Lea la sección de Uso y Cuidado Rápido. QUICK RE USE & CA 2 Retire todos los materiales de embalaje del horno microondas. 3 Instale el plato giratorio y el anillo del plato giratorio en la cavidad. 4 Reemplace el fusible del hogar o vuelva a activar el disyuntor. 5 7 MANTENGA LAS INSTRUCCIONES DE INSTALACIÖN PARA USO DEL INSPECTOR LOCAL.
Instrucciones de Instalación Impreso en China 26 49-40755 Rev.