Quick Start Guide

4
31-11025-1
3
MINIMUM CLEARANCES TO
ADJACENT WALLS & CABINETS
If a 30” clearance between the cooktop and
overhead combustible materials or metal cabinet
cannot be maintained, then a minimum clearance
of 24” is required and the underside of the cabinets
above the cooktop must be protected with not less
than 1/4” insulating millboard covered with sheet
metal not less than 30 gage (0.0125”) thick.
A ventilation hood may be installed above the
cooktop. See the ventilation hood installation
instructions for the appropriate dimensions and
clearances.
Installation Instructions
PREPARING THE OPENING
4
Make sure the wall coverings, countertop and
cabinets around the cooktop can withstand
heat (up to 200°F) generated by cooktop.
Wall covering,
cabinets and
countertop must
withstand heat up
to 200°F.
2
CUTOUT DIMENSIONS
OF THE COUNTERTOP
To ensure accuracy, it may be best to create a
template when cutting the opening in the counter.
JXTR32 CUTOUT FILLER TRIM KIT
(for use with 30” models):
A filler trim kit is available for use if your countertop
cutout is larger than the dimensions shown, up
to 29-13/16" x 20-7/16". Order JXTR32B (black) or
JXTR32W (white) to reduce the cutout opening for
installation of this cooktop. This kit may be ordered
from your dealer or directly from GE Appliances at
www.geappliances.com.
28 1/2 - 28 5/8” (30”)
33 7/8 - 34” (36”)
length of cut
1-3/4” MIN. Between
rear edge of cutout
and the wall behind
the cooktop.
19 5/8 - 19 3/4” (30”)
19 1/8 - 19 1/4” (36”)
width of cut
2-1/2” MIN. From
front edge of
cutout and front
edge of countertop.
13” max. Depth
of unprotected
overhead cabinets
30” min.
Clearance from
countertop to
unprotected
overhead
surface
30” min. for
30” cooktop
36” min. for
36” cooktop
2” min. Clearance
from cutout to
nearest vertical
wall or cabinet on
left side of the unit
below the 15” MIN.
clearance height.
15” min. Clearance
from countertop
to underside of
nearest cabinets
on both sides of
cooktop, including
any light rails.
1 1/2” min. (30”) and
2” min. (36”) Clearance
from cutout to
nearest vertical
wall or cabinet on
right side of the unit
below the 15” MIN.
clearance height.
1
APPROXIMATE COOKTOP
DIMENSIONS
Size Models X Y Z Front Z Rear*
30” JP3030T, D,
JP3530T, D
29 3/4” 20 7/8” 3 1/4 ” 4”
JP3030SJSS,
JP3530SJSS
29 7/8” 21” 3 1/4” 4”
JP5030D, PP7030D,
PP7030E, CP9530S
29 3/4” 20 7/8” 3 9/16” 5 9/16”
JP5030S, PP7030S,
PP9030S
29 7/8” 21” 3 9/16” 5 9/16”
ZEU30RS 29 7/8” 21 7/16” 3 9/16” 5 9/16”
36” PP9036S, D 36” 20 3/8” 3 9/16” 5 9/16”
ZEU36RSJSS 36 1/8” 20 7/8” 3 9/16” 5 9/16”
JP5036S, D 36 1/8” 20 7/16” 3 9/16” 5 9/16”
JP3536S, T, D 36 1/8” 20 7/16 3 9/16” 4 1/16”
* Depth at rear of cooktop at conduit location.
Cooktop
X
30” models: 19 1/4”
36” models: 18 7/8”
Z
Y
30” models: 28 1/16”
36” models: 33 3/4”