Quick Specification

Listed by
Underwriters
Laboratories
Specification Revised 10/20
PSB9240SF
GE Profile
™
Series 30 in. Single Wall Oven with Advantium
®
Technology
25-1/4"
Min.
23-1/2"
21"
30"
Installation over Warming Drawer:
2" Min.
(3" recommended)
Per warming
drawer
requirement
36-3/4" Min.
from floor
1" Min.
above
toekick
Construct solid
bottom - Min. 3/8"
plywood supported
by 2x4 or 2x2
runners all four
sides
23-1/2"
Construct solid
bottom - Min. 3/8"
plywood supported
by 2x4 or 2x2
runners all four
sides
21"
30"
Installation over a Wall Oven and Warming Drawer:
2" Min.
(3" recommended)
2" Min.
Per oven
requirement
25-1/4"
Min.
Per warming drawer requirement
45-1/4" Min.
from floor
1" Min.
above
toekick
PREPARE THE OPENING (CONT.)
When installed over a single oven
or a warming drawer, allow at least
2" between the two openings. This
separation will provide clearance for
bottom overlap of the Advantium and
the other appliance overlaps.
Construct a solid oven floor of 3/8" min.
thick plywood supported by 2 x 4 or 2 x
2 runners on all sides.
- The support must be level and rigidly
mounted, flush with the bottom edge
of the cutout.
* For existing cutouts, a maximum width
of 28-1/2" is acceptable. If the opening
is slightly wider, secure a furring strip on
each side of the cutout for securing the
oven.
NOTE: Additional clearances between the
cutouts may be required. Check to be sure
the oven supports above the Warming
Drawer location do not obstruct the
required interior depth and height. See
Warming Drawer installation instructions
for details.
INSTALLATION OVER A BUILT-IN
OVEN AND WARMING DRAWER:
* For existing cutouts, a maximum
width of 28-1/2" is acceptable. If the
opening is slightly wider, secure a
furring strip on each side of the cutout
for securing the oven.
NOTE: Additional clearances between
the cutouts may be required. Check
to be sure the oven supports above
the Warming Drawer location do not
obstruct the required interior depth and
height. See Warming Drawer installation
instructions for details.
CAUTION: For personal safety, the
mounting surface must be capable of
supporting the cabinet load, in addition
to the added weight of the oven and
drawer, plus additional oven loads.
PREPARE THE OPENING: The Advantium 120V
can be installed in combination with other Built-In
appliances. Always follow each product's Installation
Instructions to compete the installation.
SINGLE OVEN INSTALLATION: Order a 30" wide
single oven cabinet or cut the opening in a wall to the
dimensions shown.
* For existing cutouts, a maximum
width of 28-1/2" is acceptable.
If the opening is slightly wider,
secure a furring strip on each side
of the cutout for securing the oven.
- Always maintain 36-3/4"
minimum height from the floor
to the cutout in any single or
combined installation.
- The unit overlap on the top is
1/2" but allow 5/8" clearance
from top edge of cutout. The unit
overlap on each side is 2−1/4" but
allow 2−3/8" clearance from side edges of cutout. The unit overlap
on the bottom is 5/8" but allow 3/4" clearance from bottom edge of
cutout.
- Oven overlaps will conceal cut edges on all sides of the opening.
25-1/4"
23-1/2"
Construct base -
Min. 3/8" plywood
supported by 2x4
or 2x2 runners all
four sides.
21"
30"
36-3/4" Min.
from floor
1" Min.
above
toekick
PREPARATION WITH AN ACCESSORY DRAWER