Installation Guide
2 A
CUTOUT FOR SINGLE OVENS IN WALL CABINET
NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick,
shim both sides equally to establish the cutout width.
2 B
CUTOUT FOR SINGLE OVENS – UNDER COUNTER
NOTE: These ovens are only approved to be installed under the specific models as labeled on
the unit.
NOTE: One cooktop may be centered over either
oven in the side-by-side installation.
Cutout – observe
all dimensions and
requirements.
2” (5.1 cm) Min.
30.5” (77.5 cm) 30” models
Center Line Center Line
Side-by-Side Installations
Install two ovens in separate cutouts.
Cooktop
Cutout – observe
all dimensions and
requirements.
Continue to Section 4.
Dimension Dimension Description 30” Single Oven
A Cabinet Width 28
1
»2” (72.4 cm) min.
28
5
»8” (72.7 cm) max.
B Cutout Height 27
1
»4” (69.2 cm) min.
27
5
»16” (69.4 cm) max.
C Clearance from cutout - top* 1” (2.5 cm)
(1
1
»4” (3.2 cm) for PT9050
ZET1S and ZET1P)
D Clearance from cutout - bottom* 1
1
»4” (3.2 cm)
E Clearance from cutout - side edges*
11
»16” (1.75 cm)
F Junction Box Location 9
1
»2” (24.1 cm) max.
right side only
* Refers to minimum clearance required for wall oven installation and does not reflect actual product dimensions.
IMPORTANT: Maintain
a minimum distance
of 31-1/4” from the
top surface of the
countertop to the
wall oven platform to
ensure that the cooktop
and wall oven do not
interfere with each other
(see picture).
31-1/4” min.
(79.4 cm)
SIDE VIEW
Cooktop
Wall Oven
2-1/2” min. (6.4cm)
These ovens are not approved for
installations that stack one single wall
oven above another single wall oven.
Cutout –
observe all
dimensions and
requirements.
Cutout –
observe all
dimensions and
requirements.
2” (5.1 cm) Min.
30.5” (77.5 cm)
30” models
Center Line Center Line
Side-by-Side Installations
Install two ovens in separate cutouts.
Door handles should face toward each other
B
F
G
C
D
A
Recommended
Cutout Location
from Floor
32-1/2” (82.6 cm)
Dim. Dimension Description 30” Single Oven
A Cabinet Width 30” (76.2 cm)
B Cutout Width 28
1
»2” (72.4 cm) min. / 28
5
»8” (72.7 cm) max.
C Cutout Height 27
1
»4” (69.2 cm) min. / 27
5
»16” (69.4 cm) max.
D Clearance from cutout - side edges*
11
»16” (1.75 cm)
E Clearance to Adjacent Corners, Drawers, Walls, etc.,
When Door Is Open
31
1
»8” (77.8 cm) min.
F Clearance from cutout - top* 1” (2.5 cm) min. (1
1
»4” (3.2 cm) for PT9050,
ZET1S and ZET1P)
G Clearance from cutout - bottom* 1
1
»4” (3.2 cm)
H Junction Box Location 9
1
»2” (24.1 cm) max. right side only
J Door swing depth - Allow additional clearances for
installation and oven usage
31
1
»8” (77.8 cm) min.
K Countertop or cabinet door protrusion (measure if exist) Measure “K”
L Gap between edge of countertop or cabinet door to
cabinet opening
If K = 0, L = 0, Otherwise
K = L + 1” (2.54 cm) min.
P Junction Box location 5-1/4” (13.34 cm) max.
R Junction Box location 2-1/2” (6.35 cm) max.
S Door swing width - Allow additional clearances for
installation and oven usage
24” (61 cm) min.
* Refers to minimum clearance required for wall oven installation and does not reflect actual product dimensions.
K
J
S
L
H
E
Junction Box
Location
(junction box
may be located
in adjacent
cabinet)
Cutout Depth
23-1/2”
(59.7 cm) Min.
Opening
Between Inside
Walls Must be
at Least 28-1/2”
(72.4 cm) Wide
NOTE: Allow
1/4” (0.64 cm)
clearances from
side edges of
oven door.
LH door swing
shown.
RH door swings
opposite.
P
R