GE Security NX-10 Alarm System Installers Manual 1060789
Copyright Copyright © 2009, GE Security B.V. All rights reserved. This document may not be copied or otherwise reproduced, in whole or in part, except as specifically permitted under US and international copyright law, without the prior written consent from GE. Document number/revision: 1060789 June 2009 Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
NX-10 Installers manual 3 Table of Contents Preface ................................................................................................................................................................ 9 Safety terms and symbols.............................................................................................................................................. 9 References....................................................................................................................
Selecting a menu option...............................................................................................................................................38 Changing a menu option..............................................................................................................................................38 Changing selection list entries.....................................................................................................................38 Changing binary entries .
NX-10 Installers manual 5 Configuring partitions ....................................................................................................................................................60 Setting timers.......................................................................................................................................................60 Configuring a partition ......................................................................................................................
Setting the exit buzzer options................................................................................................................. 153 Glossary............................................................................................................................................................................. 154 Technical specifications.............................................................................................................................................
NX-10 Installers manual 7 Troubleshooting...............................................................................................................................................197 Autotest ...............................................................................................................................................................197 Reporting protocols and formats ......................................................................................................................
Programming tasks ....................................................................................................................................... 239 Chapter B11 Updating firmware ............................................................................................................... 242 Overview ........................................................................................................................................................................... 242 Update procedure ......
NX-10 Installers manual 9 Preface This is the NX-10 Installers manual. This document includes an overview of the product and detailed instructions explaining: • how to install and configure the components of your NX-10 system; and • how to program the system. To use this document effectively, you should have the following minimum qualifications: • a basic knowledge of alarm systems and components; and • a basic knowledge of electrical wiring and low-voltage electrical connections.
Section A Installing and programming a basic system
NX-10 Installers manual 11 Chapter A1 Introducing the NX-10 system NX-10 diagram Figure 1.
Earth T1 T R R1 AUX PWR+ 1 COM 2 DATA POS COM BELL+ BELLAUX PWR+ RLY1 NC RLY1 NO RLY1 C RLY2 NC RLY2 NO RLY2 C COM AUX PWR+ Figure 2.
NX-10 Installers manual NX-10 technical specifications Mains power specifications Mains input voltage, small housing 230 V ~ (+10% / - 15%) / 50 Hz / 25 VA Mains input voltage, large housing 230 V ~ (+10% / - 15%) / 50 Hz / 40 VA Current, typical system, 25 VA transformer 0.12 A ~ / 50 Hz / 25 VA Current, typical system, 40 VA transformer 0.20 A ~ / 50 Hz / 40 VA Board input voltage 16.5 V ~ / 50 Hz Power supply specifications ± 2% Output voltage 13.8 V Maximum total current, 25 VA (40 VA) 1.
NX-10 system NX-10 Number of wireless zones 48 Number of onboard hardwired zones 2 Maximum number of hardwired zones 42 Maximum number of zones 48 zones (if 2 hardwired zones are used, than there are 46 wireless zones left to use) Number of partitions 4 Maximum number of wireless outputs 8 (including sirens) Outputs on board 2 open collector, 1 internal siren Maximum number of RF output modules 4 (including sirens) Report formats Contact ID, Ademco 4/2 Express, Siren Tone, Vocal, Radionics
NX-10 Installers manual Part number Description 15 Purpose NX-1701E Door swipe module Proximity card reader/door control module. You can program it to control access in any or all partitions. NX-320-I Auxiliary power module Provides additional power for modules attached to a panel. NX-507E/NX508E Output expander module Expands the number of outputs available on the system.
Table 2. Wireless equipment Part Number Part Description Purpose TX-7001-05-1 INDOOR SIREN, 868 MHz GEN2 This full wireless indoor siren offers you wireless communication and wireless operation by batteries with a typical sound output of 108dB. TX-7201-05-1 OUTDOOR SIREN, 868 MHz GEN2 This full wireless outdoor siren offers you wireless communication and wireless operation by batteries with a typical sound output of 125dB. BS7201 Spare battery pack for the TX-7201-05-1 siren.
NX-10 Installers manual 17 TX-4131-03-2 4 BUTTON KEYFOB, 868 MHz GEN2 The 4-button keyfob is a portable wireless device allowing you to arm or disarm the system without having to memorise access codes or race to beat entry or exit delays. It offers two additional programmable buttons, which can be used to turn lights on and off before entering the premises, or any other function defined in the system.
Keypads Wireless keypad The wireless LCD keypad allows you to program the NX-10 system using a menu structure. There is also an option to use the wired keypad with the same functionality. Figure 3. Keypad. The LCD features the white backlight to allow keypad operation in the dark. Illumination level is as low as possible to save energy. LCD backlight turns ON gradually when the user hits the first key, and turns OFF gradually 30 seconds after the last key operation.
NX-10 Installers manual The NX-10 keypad has the following key layout out-of-the-box: Figure 4. Default keypad layout. F1 F2 F3 F4 F5 F6 F7 F8 The four top-row keys with the blank keycaps can be replaced by the installer, as they are supplied with the keypad for this purpose. Figure 3 shows the keypad with the optional function keycaps placed in their default positions (factory setting).
Press to scroll to the start of the LCD message. Disarm When in master mode: Press to disarm the system. Note: The Disarm key works in the master mode only, after the user code and the partition number have been entered. When in the menu: Press to scroll to the end of the LCD message. Bypass Press to select a zone to bypass. Night Mode Press to arm the system in Night mode. Chime Press to toggle the Chime mode on and off. A chime is often used as an indication on a shop door.
NX-10 Installers manual LCD icons The LCD display for the NX-10 keypad consists of two separate sections, one for displaying 2 rows of 16 characters of alphanumeric data, and one for showing icons. The display section on the wireless keypad showing alphanumeric data is only turned ON while the user is operating the keypad, and turns OFF 30 seconds after the last key hit. The icon section is always ON and shows all kinds of conditions as explained in Table 4.
8 Battery low This icon is only available on the wireless keypad and flashing when the keypad battery is low. 9 This icon flashes in case of an alarm condition. Alarm 10 11 This icon is only available on the wireless keypad and indicates RF-link field strength. The one most to the left indicates absence of RF, the one most to the right indicates full signal strength. It will flash as long as the keypad is not registered yet.
NX-10 Installers manual Chapter A2 Installation guidelines Mains power connection Use the mains connector terminal for connecting the mains supply. You can use a fixed cable or a flexible mains lead to an earthed mains outlet. If fixed wiring is used, insert a dedicated circuit breaker in the power distribution network. In all cases, the mains connection must comply with local regulations. WARNING: Disconnect the mains power before opening the cabinet.
electrician or other suitably trained and qualified person should attempt to wire this system to the mains or to the public telephone network. 1. Ensure that there is a good earth for the alarm system for effective resistance to electrical interference. Provide an earth connection for the standalone telephone dialer. 2. For mains power connection, use the mains connector terminal either via permanent wiring or a doubly insulated flexible mains cable to an earthed mains outlet.
NX-10 Installers manual Chapter A3 Installing a basic system Installing the NX-10 CAUTION: Before installing the panel: • Ensure that the unit is mounted on a flat, solid, vertical surface so that the base will not flex or warp when the mounting screws/bolts are tightened. • Leave a 50 mm clearance between equipment enclosures mounted side by side and 25 mm between the enclosure and the cable pathway.
Figure 5. Connecting the battery to the panel. 9. Close the housing. Installing the keypad Mounting the wireless keypad Depending on the configuration, the wireless keypad can be mounted on the wall in a cradle or used as a portable device. To install a wireless keypad: Figure 6. Mounting the wireless keypad. ! 1. 2. " Ensure that the keypad is mounted on a flat, solid, vertical surface so that the base will not flex or warp when the mounting screws/bolts are tightened.
NX-10 Installers manual 3. Place the keypad in the cradle inserting the bottom edge first ", and carefully push the top until the keypad snaps in place. Note: To replace keypad batteries, see the Battery replacement section on page 148, and the Battery replacement chapter in the NX-10 User Guide. Note: Any unauthorized opening of the battery compartment will cause tamper alarm in the system. Mounting the wired keypad There is also an option to use wired keypads with the NX-10 system.
4. Figure 9. At the panel side, run the NetworX bus wires through the ferrite (see Figure 9, position 1), making one loop, and connect the wires to the standard NetworX bus contacts (see Figure 1, position 4). Additionally, connect the shielding to COM (see Figure 9, position 2). Panel connector block and the ferrite. 2 1 5. Carefully close the keypad and tighten the 2 screws at the bottom side. Note: Any opening of the keypad enclosure will cause tamper alarm in the system. 6. Power up the panel.
NX-10 Installers manual not communicate with the panel in this time window, the learning mode is exited. The learning mode can be restarted by switching panel power off and on again. Insert the batteries in the wireless keypad. It starts the keypad initialization process. 2. Note: If the keypad is not brand new (i.e.
To install the wireless siren: 1. Select the appropriate location to install the siren, and mount the siren base to the wall. 2. Insert the batteries to power the siren. In case of the indoor siren, the battery holders for four (4) AA 1.5 V batteries and one (1) 9 V battery are located inside the housing of the siren. In case of the outdoor siren, you should install the battery pack inside the housing of the siren. The battery pack contains independent batteries for the speaker and the beacon. 3.
NX-10 Installers manual Figure 10.
TX-7001-05-1 Wireless indoor siren specifications Power supply specifications Electronics Siren part Number and type of batteries 4 x AA size, 1.5 V, primary cell Battery capacity 5600 mAh Board operating voltage 2.1 V … 3.1 V Number and type of batteries 1 x 9V size block, primary cell Battery capacity 600 mAh Operating voltage 9 V … 12 V Battery lifetime (typical) 3 years * Current consumption – IO module (typical) 160 uA at 3.
NX-10 Installers manual Figure 11.
To allow the IO module to control the output on the outdoor siren, you need to cut jumper 3 and then optionally 1 and/or 2. Jumper 3 is a start-up protection. Jumpers 1 and 2 are responsible for timer settings, and you can cut one of them or both, according to the table below. The maximum siren activity time is limited both by hardware (jumper) setting, and software (RF Receiver 32>Outputs>Siren/IO>Time) time setting, whichever is shorter.
NX-10 Installers manual Installing the wireless sensors Mounting the sensors 1. Select the appropriate location to place the sensor. For recommendations and rules regarding a correct placement of the particular sensor (motion sensor, door/window, smoke, etc.), see the sensor manual enclosed with the device you want to install. 2. Fasten the sensor base to the wall. 3. Place the sensor battery in the battery holder. 4. Re-install the sensor board and the cover plate.
Chapter A4 Programming guidelines Getting started This chapter describes a NX-10 installation with the menu driven keypad allowing you to program the system easily using a menu structure. Country codes The NX-10 has the ability to set different “country codes”. Each country code has specific default settings.
NX-10 Installers manual Powering up the system When the NX-10 is powered up for the first time, the keypad language, keypad defaults, partition and keypad number must be set. These options must also be set each time a keypad is defaulted. 5. The Set KP Language option sets the first language of the keypad. 6. The Load Country Defaults option sets the country specific keypad defaults. It does not default the keypad. 7. The Partition Number and Keypad Number options set the keypad address.
Navigating the menus Note: • Press the ½¾ keys to scroll through menu lists and options. • Press #½ to move to the same menu item for the previous option. For example, if you are in a submenu for zone 2, press #½ to move to the same submenu for zone 1. • Press # ¾ to move to the same menu item for the next option. For example, if you are in a submenu for zone 2, press #¾ to move to the same submenu for zone 3. The keypad may timeout from the menu system and return to the default display.
NX-10 Installers manual Press NO to cancel the change and return to the menu option. 5. Changing binary entries 1. Navigate with the ½¾ keys to the relevant menu option and press OK. 2. The current value for the menu option is displayed, for example, 1 2 3 - - - - 8 means that 1, 2, 3 and 8 are on (included) while 4, 5, 6 and 7 are off (excluded). 3.
4. 5. • Press ¾ to delete the number at the cursor position. • Press #¾ to delete all the numbers from the number at the cursor position to the end of the string. Do one of the following: • Press the keys 0 to 9 to insert new numbers. • Press #0 to insert G (to use the GSM instead of the PSTN). • Press #1 to insert a star. • Press #2 to insert #. • Press #3 to insert a four-second delay. • Press #4 to insert P (this enables pulse dialing). Press OK to accept the changes.
NX-10 Installers manual The current text for the menu option is displayed, for example, Zone 2. 3. 4. Do one of the following: • Press ½ to toggle between insert mode and overwrite mode (insert mode allows you to insert new text and overwrite mode allows you to overwrite existing text). • Press ¾ to delete the character at the cursor position. • Press #¾ to delete all the characters from the character at the cursor position to the end of the string. 5. Press the keys 0 to 9 to insert new characters.
2. The current state of the word library is displayed. In this case, it is enabled. 3. Use the ½¾ keys to change the state to disabled and press OK. 4. The keypad beeps once to accept the change and returns to Word Library. Note: In case of wireless keypads, user texts (user names, zone names, etc.) are copied from the keypad to the RF receiver first and then sent to the target keypad (or one-by-one to consecutive keypads).
NX-10 Installers manual Exiting the program mode When you have made all the desired changes in programming, it is time to exit the program mode. Press the NO key twice to exit this programming level, and go to the “Enter the device address” level. If no additional modules are to be programmed, press the NO key twice again to display the OK to Exit prompt, and press OK to exit the program mode.
Chapter A5 Setting up a communicator Reporting The NetworX system supports different modes of reporting events to multiple central stations. There are three phone numbers - each phone number has it own account code, protocol and events. The configured prefix is common to all three phone numbers. If a four-second delay is specified in the prefix, the panel does not look for a dial tone, but performs blind-dialling. The following scenarios are examples of how to set different modes of reporting.
NX-10 Installers manual by default and events for phone numbers 2 - 3 are disabled by default. If phone number 1 and phone number 2 are programmed, the default sequence is 1,1 2,2 1,1,2,2 for a total of eight calls to each number. Table 8.
Level 1 Level 2 Value State Events Phone Number 1 – Alarms Enabled Phone Number 1 – Alarm Restores Enabled Phone Number 1 – Tampers and Restores Enabled Phone Number 2 – Alarms Enabled Phone Number 2 – Alarm Restores Enabled Phone Number 2 – Tampers and Restores Enabled Split reporting Split reporting configures the control panel to report to two different central stations. Some events must be reported to phone number 1 and others to phone number 2.
NX-10 Installers manual Chapter B1 Selecting the programming mode The NX-10 system allows to use two different programming modes — location-based programming or menu-based programming. In location-based programming you use locations and segments to set appropriate values. In menu-based programming you use a menu tree to enable/disable particular options or to set values. To select the programming mode: 3. Press OK at the system prompt and enter your installer code. 4. The OK=LOC ½¾=MENU prompt displays.
Chapter B2 Programming the control panel Overview You must default the control panel before you begin to program the system. For more information on enrolling and defaulting, see Chapter B7 Enrolling modules. Programming inputs Figure 13. Inputs menu 2.1.1 Zones 2.1.1.1 (1) Zone 1 Zones 2 - 48 Same as above If more than 8 zones, zones are first displayed in groupsof 8 and then as above. 2.1.2 Swinger Count 2.1.3 Zone Types 2.1.3.1 (1) Day Zone 2.1.1.1.1 Zone Type 2.1.1.1.2 Zone Name 2.1.1.1.
NX-10 Installers manual 49 A zone may reside in any combination of partitions. A zone that resides in more than one partition becomes a common zone and is reported to its lowest partition number. A common zone is armed only when all the partitions that it belongs to are armed. It is immediately disarmed when one of the partitions it belongs to is disarmed. The control panel can have a maximum of two on-board hardwired inputs, and a total of 48 zones (wired and wireless together).
is resident, as long as the zone is open. Keyswitch arming will report as User 99 in logs and reports. Entry/Exit 1 Force Armable A trip will start entry delay 1. Absence of a trip during exit delay will enable the automatic bypass or instant mode, if so programmed. This zone is force armable, which means the system can be “Force Armed” even if this zone has been violated. In this condition, the “Ready” icon will flash indicating the zone is not secure.
NX-10 Installers manual 8. Press OK to accept the changes. 9. The keypad beeps once to confirm the change and returns to Zone Name. 10. Scroll to Partitions and press OK. The current partition(s) for that zone are displayed, for example, 1 - - - means that the zone is assigned to partition 1. 11. Press the corresponding numerical key to include or exclude a partition, for example, press 1 to exclude partition 1 and press 3 to include partition 3. The display changes to - - 3 -.
7. Set the value of Inputs>Swinger Count to 5. For more information see Setting swinger count below. Setting swinger count The swinger shutdown function allows the selected zone to be automatically bypassed after a specified number of alarms. To configure swinger count, you must enable the advanced menu. The following example sets swinger count to 5. This means that any zone for which swinger shutdown is enabled can be activated five times within one arm period before it is automatically bypassed.
NX-10 Installers manual The control panel includes up to 2 programmable on-board auxiliary outputs. To program on-board outputs, select Installer Menu>Control Panel>Outputs. Configuring an output You can change the characteristics of each output. You must specify the events and/or partitions that activate an output and the length of time for which the output is activated. The events are grouped in the programming tree.
Data 25 26 27 28 29 Event Data Fire Fire trouble Chime Expander trouble Dynamic battery test time 55 56 57 58 59 Event Auxiliary communication failure Radio test Any siren when armed in any mode Alarm memory (pulsating) Zone inactivity If set to follow condition, these events are one second. Note: When Event 48 is programmed, it is possible to program a user code's authorization to select which output(s) a particular code activates.
NX-10 Installers manual silent alarm that sends a special report to the central station. To program codes, select Installer Menu>Control Panel>Codes. Note: For EN/INCERT compliance, system access ID needs to be in 6 digit format. Setting up the installer code An installer code may have associated arming options and access rights. To set the authority and access rights, you must enable the advanced menu.
Setting communication options Figure 16. Communication menu 2.4.1 Central Station 2.4.1.1 Phone Numbers 2.4.1.1.1 Phone Number 1 Phone Numbers 2 - 6 Same as above 2.4.1.1.1.5 Phone Number Account Code Protocol Dial Attempts Backup Control 2.4.1.1.1.6 Events 2.4.1.1.1.1 2.4.1.1.1.2 2.4.1.1.1.3 2.4.1.1.1.4 2.4.1.1.1.4.1 Arm/Disarm/Alarm 2.4.1.1.1.4.1.1 2.4.1.1.1.4.1.2 2.4.1.1.1.4.1.3 2.4.1.2 Account Codes 2.4.1.3.1 2.4.1.1.1.4.1.4 (1) Partition 1 Partitions 2 - 4 Same as above 2.4.1.3 2.4.
NX-10 Installers manual Figure 17. Report codes menu 2.4.4.3 Report Codes 2.4.4.3.1 2.4.4.3.2 Zone Types Partition Reports (1) Day Zone 2.4.4.3.1.1.1 Zone Types 2 - 30 Same as above 2.4.4.3.1.1.2 2.4.4.3.1.1 (1) Partition 1 2.4.4.3. 2.1 Partitions 2 - 4 Same as above 2.4.4.3.1.1.3 2.4.4.3.2.1.1 2.4.4.3.2.1.2 2.4.4.3.2.1.3 2.4.4.3.2.1.4 2.4.4.3.2.1.5 2.4.4.3.2.1.6 2.4.4.3.2.1.7 2.4.4.3.2.1.
press OK. 3. Scroll to Phone numbers>Phone Number 1>Dial Attempts and press OK. 4. Select 3 and press OK. 5. The keypad beeps once to confirm the change and returns to Dial Attempts. Defining communication with a mobile phone You can also treat a telephone (for example, your mobile phone) as a central station. This way you can send voice messages with the NX-535 voice module (if installed) when particular events happen, or you can send a siren tone to your mobile phone in case of an alarm.
NX-10 Installers manual 2. Scroll to Interval>7 days and press OK. 3. The keypad beeps once to confirm the change and returns to Hours/Days?. 4. Scroll to Hour>12 and press OK. 5. The keypad beeps once to confirm the change and returns to Hour. 6. Scroll to Minutes>45 and press OK. 7. The keypad beeps once to confirm the change and returns to Minutes. 8. Scroll to Time Since Test>5 Days and press OK. 9. The keypad beeps once to confirm the change and returns to Time Since Test.
Configuring partitions Figure 18. Partitions menu (1) Partition 1 2.5.1 2.5.1.1 Timers 2.5.1.1.4 Entry Time 1 Exit Time 1 Entry Time 2 Exit Time 2 2.5.1.2.1 Arming 2.5.1.1.1 2.5.1.1.2 Partitions 2 - 4 Same as above 2.5.1.1.3 2.5.1.2 Feature Select 2.5.1.2.1.1 2.5.1.2.1.2 2.5.1.2.1.3 2.5.1.2.1.4 2.5.1.2.1.5 2.5.1.2.1.6 2.5.1.2.1.7 2.5.1.2.1.8 2.5.1.2.1.9 2.5.1.2.1.10 2.5.1.2.1.11 2.5.1.2.1.12 2.5.1.2.2 Keypads 2.5.1.2.2.1 2.5.1.2.2.2 2.5.1.2.2.3 2.5.1.2.2.4 2.5.1.2.2.5 2.5.1.2.2.6 2.5.1.2.
NX-10 Installers manual according to the auto-arm schedule, and enables the personal alarm combination keys so they activate a personal attack alarm when pressed. 1. Ensure the advanced menu is enabled. 2. Navigate with the ½¾ keys to Control Panel>Partition Settings>Partition 1>Feature Select>Arming and press OK. 3. Scroll to Silent Auto Arm>Yes and press OK. 4. The keypad beeps once to confirm the change and returns to Silent Auto Arm. 5.
Setting timers You can set timers to control the duration of various system functions. The following example sets the internal siren timer to five minutes. When the siren starts ringing, the timer starts counting down. When the timer is finished, the siren automatically stops. 1. Ensure the advanced menu is enabled. 2. Navigate with the ½¾ keys to Control Panel>System Settings and press OK. 3. Scroll to Timers>Sounders>Internal Siren Timeout and press OK. 4. Enter 5 and press OK. 5.
NX-10 Installers manual Setting arm schedules Figure 20. Arm Schedules menu 2.7.1 Arm Only After Close 2.7.1.1 (1) Partition 1 Partitions 2 - 4 Same as above 2.7.1.1.1 2.7.1.1.2 2.7.1.1.3 2.7.1.1.4 2.7.1.1.5 2.7.1.1.6 2.7.1.1.7 2.7.2 Auto Arm 2.7.2.1 (1) Partition 1 Partitions 2 - 4 Same as above 2.7.2.1.1 2.7.2.1.2 2.7.2.1.3 2.7.2.1.4 2.7.2.1.5 2.7.2.1.6 2.7.2.1.7 2.7.2.1.8 2.7.3 Auto Disarm 2.7.3.1 (1) Partition 1 Partitions 2 - 4 Same as above 2.7.3.1.1 2.7.3.1.2 2.7.3.1.3 2.7. 3.1.4 2.7.
7. Navigate with the ½¾ keys to Schedule Times>Closing/Autoarm>Hour and press OK. 8. Enter 18 and press OK. 9. The keypad beeps once to confirm the change and returns to Hour. 10. Scroll to Minute and press OK. 11. Enter 0 and press OK. 12. The keypad beeps once to confirm the change and returns to Minute. Glossary Location Term Definition 2 Control Panel This groups all options relating to the central processing unit of the alarm system.
NX-10 Installers manual Location Term Definition 2.1.3.1.1.2 24-hour A zone type where reaction is not dependent on the arm/disarm state of the system. It is permanently active 24 hours a day unless bypassed by forced arming. An example of a 24-hour zone is a fire, panic or glassbreak zone. 2.1.3.1.1.3 Keyswitch A zone type that can be used to arm or disarm a partition using a switch connected to a zone instead of a code. Both pulsed and maintained keyswitches can be used. 2.1.3.1.1.
Location Term Definition 2.1.3.1.3.4 Swinger Zone A zone characteristic that allows the selected zone to be automatically bypassed after a specified number of alarms. 2.1.3.1.3.5 Bypassable A zone characteristic that allows the zone to be bypassed. 2.1.3.1.3.6 Force Armable A zone characteristic that allows the zone to be force armed. 2.1.3.1.3.7 Group Bypass A zone characteristic that allows the user to bypass multiple zones with a single operation. 2.1.3.1.3.
NX-10 Installers manual Location Term Definition 2.1.3.1.5.3 Dialer Delay A menu option that sets the length of time (in seconds) the dialer waits before reporting an abortable alarm. If the system is disarmed during this time, the abortable alarm is not sent to the central station. The delay can be from 0-255 seconds. A value of 0 means that there is no abort delay. 2.1.3.1.5.4 Listen-in A menu option that sends a report to the central station indicating that a listen-in session must be started.
Location Term Definition 2.2.1.1.4 Partitions A menu entry that lists the partitions assigned to the selected output. The selected output can be triggered by an event on these partitions. A zone may reside in any combination of partitions. A zone that resides in more than one partition becomes a common zone and is reported to its lowest partition number. A common zone is armed only when all the partitions that it belongs to are armed.
NX-10 Installers manual Location Term Definition 2.2.2.2.2 Exit Delay Expired A menu option that causes the internal sounder to blast when the exit time expires. 2.2.2.2.3 Closing Kissoff A menu option that causes the internal sounder to blast when the central station receives a closing report. 2.2.2.2.4 Keyswitch Arming A menu option that causes the internal sounder to blast when the system is armed by keyswitch or armed and disarmed by keyswitch.
Location Term Definition 2.3.2.2 Authority A menu entry that groups access options. These options specify the level of access an individual has when using the control panel. 2.3.2.2.1 Arm Only After Closing A menu option that specifies a code that arms the system during the close window only (when the system is scheduled to be armed). If entered during the open window when the system is turned off, the code does not arm the system. 2.3.2.2.
NX-10 Installers manual Location Term Definition 2.4.1 Central Station A menu entry that groups options relating to the central station. This is a remote location that is designed to monitor signals and reports from alarm systems and summon assistance if necessary. This is also known as a control station or ARC. 2.4.1.1 Phone Numbers A menu entry that groups phone number reporting options. 2.4.1.1.1.1 Phone Number A menu option that sets the phone number to which events are reported.
Location Term Definition 2.4.1.1.1.6.1.3 Opening/Closing A menu option that sends a report to the selected phone number stating when the system is opened (disarmed) and closed (armed). 2.4.1.1.1.6.1.4 Zone Bypass and Restores A menu option that sends a report to the selected phone number when a zone is bypassed. A report is also sent when the zone is restored (un-bypassed). 2.4.1.1.1.6.
NX-10 Installers manual Location Term Definition up/download events to the selected phone number. 2.4.1.1.1.7 Partitions to Report A menu option that specifies which partitions are reported to the selected phone number. Important: When you select a partition, ALL events from this partition are reported to the assigned central station, and individual event settings selected in the Events section are disregarded.
Location Term Definition 2.4.2.6 Call PC on Autotest A menu option that allows the panel to use call back when the central station performs an autotest. After the test report is delivered to the central station, the panel calls the up/download software using the call back phone number. Actions, such as upload event log and download phone numbers, can be selected in the up/download software. 2.4.2.
NX-10 Installers manual Location Term Definition 2.4.4.1 Partition Reports A menu option that specifies the events that are enabled for each partition. Events specified in this option are related to all partitions in the system. 2.4.4.1.1 Opening/Closing A menu option that enables opening/closings reporting. 2.4.4.1.2 Zone Bypass A menu option that that sends a report to the central station when zones are bypassed. 2.4.4.1.
Location Term Definition 2.4.4.2.1.5 RF Low Battery A menu option that sends a report to the central station when a low battery condition occurs in an RF sensor. 2.4.4.2.1.6 CleanMe A menu option that sends a report to the central station when a smoke detector is dirty. 2.4.4.2.2 Power A menu entry that groups the power events that are reported to the central station. 2.4.4.2.2.1 Mains Failure A menu option that sends a report to the central station when the mains power supply fails.
NX-10 Installers manual Location Term Definition 2.4.4.3.1 Zone Types A menu entry that groups all reporting codes for the selected zone type. 2.4.4.3.1.1.1 Event Code A menu option that sets the event code reported for the selected zone type. 2.4.4.3.1.1.2 SIA Code A menu option that sets the SIA code reported for the selected zone type. 2.4.4.3.1.1.3 CID Code A menu option that specifies the Contact ID code to be used when reporting the selected zone type. 2.4.4.3.
Location Term Definition 2.4.4.3.3.5 Keypad Tamper A menu entry that groups the report codes sent for the keypad tamper event. 2.4.4.3.4 Power A menu entry that groups report codes sent to the central station when power related events occur. 2.4.4.3.4.1 Mains Failure A menu entry that groups the codes used to report a mains failure event. 2.4.4.3.4.2 Low Battery A menu entry that groups report codes sent to the central station for a low battery event.
NX-10 Installers manual Location Term Definition 2.4.4.3.6.6 End Download A menu entry that groups the report codes sent to the central station when downloading is complete. 2.4.5 Custom Format A menu option that allows you to build communication formats if using a non-standard central station. Consult technical support before using this option and the related options. 2.4.5.1 Features 1 A menu option that allows you to configure your own reporting protocol based on the options enabled.
Location Term Definition 2.5.1.2.1.1 Quick Arm A menu option that enables the function keys for part arming and for full arming. These options work on a singlepartition keypad only. If the Quick Arm menu option is enabled, the user can arm the system by simply pressing the Arm Away, Arm Stay or Night Mode button, otherwise it is necessary to enter the user code first. (To arm a system in the Away mode with a single-partition keypad it is enough to enter the user code). 2.5.1.2.1.
NX-10 Installers manual Location Term Definition 2.5.1.2.1.10 Keyswitch Arm Stay A menu option that allows to arm the partition in Stay mode with a keyswitch. 2.5.1.2.1.11 Late to Close/Early to Open A menu option that sends a report to the central station when the system is armed late or disarmed early. If an opening occurs before the preset opening time, the control panel will send an "Early Open" report.
Location Term Definition to work on a particular keypad in the particular partition. When the user sets the LED Extinguish option for the Control Panel to Enable then he must restart power supply for the control panel. After restarting, this function will be enabled. When the user wants to disable this option he must set it to Disable, and restart the power supply. The system then waits for a valid user code.
NX-10 Installers manual Location Term Definition 2.6.1.1.4 Cross Zone Timer A menu option that sets the cross zone time in minutes. This can be from 0 to 255 minutes, where 0 = no cross zoning. 2.6.1.2 Power A menu entry that groups the timer options relating to power events. 2.6.1.2.1 Batt Dynamic Test Duration A menu option that sets the length of time that the control panel performs the Dynamic Battery test. This can be between 0 to 30 minutes where 0 is no test. 2.6.1.2.
Location Term Definition 2.6.2 Feature Select A menu entry that groups all optional features relating to control panel system settings. 2.6.2.1 Inputs A menu entry that groups options that enable features relating to inputs. 2.6.2.1.1 On-board zones A menu option that disables the wired zones on the control panel. This provides a completely wireless alarm system. 2.6.2.1.2 Box Tamper A menu option that enables the box tamper switch on the control panel.
NX-10 Installers manual Location Term Definition 2.6.2.2.4 Manual Dialer Test A menu option that includes a dialer test in the user’s manual test. A manual test call is made to the central station and the corresponding signal is transmitted. 2.6.2.3 Clock A menu entry that groups options that configure the clock. 2.6.2.3.1 Use Int.Crystal for Clock A menu option that provides an accurate clock in situations where different mains frequencies are used: 50 Hz or 60 Hz are possible selections. 2.6.
Location Term Definition 2.7.1 Arm Only After Close A menu option that specifies the days of the week that each partition is open. On these days, “arm only after closing” codes will be able to arm and disarm during the open window. On days not selected here, “arm only after closing” codes will not disarm. 2.7.2 Auto Arm A menu option that allows the control panel to auto arm at a specified time. At this time, the keypad beeps for 50 seconds before the panel arms.
NX-10 Installers manual default. If you want pulse tone dialling, program a “15” in the segment where pulse dialling should begin. If the entire number should be pulse dialling, program a “15” in the first segment. Program an “11” for a “*”, and a “12” for a “#”. Note: A zero is programmed as a “0”. LOCATION 1 - ACCOUNT CODE FOR PHONE N° 1 (6 segments, numerical data) Location 1 is used to program the account code that is sent when phone N°1 is dialled. A zero in the account code is programmed as a “0”.
Location 4 is used to select which events are reported to phone N°1. Location 5 is used to select which partitions are reported to phone N°1. If you do not want dual or split reporting, use location 4 to select all events to phone N°1, and leave location 5 at the factory default of “0”. If you want dual or split reporting, and the split is based on the event type (such as alarm, open/close, etc.
NX-10 Installers manual tone dialling, program a “15” in the segment where pulse dialling should begin. If the entire number should be pulse dialling, program a “15” in the first segment. Program an “11” for a “*”, and a “12” for a “#”. Note: A zero is programmed as a “0”. LOCATION 7 - ACCOUNT CODE FOR PHONE N° 2 (6 segments of numerical data) Use location 7 to program the account code that is sent when phone N°2 is dialled. A zero in the account code is programmed as a “0”.
Reporting events to phone number 2 Phone N°2 can be used to back up phone N°1, or as a second receiver to multi-report or split-report events. Phone N°2 has two programming locations that are used to select the events that are reported to this phone number. Location 10 is used to select the events which are reported to phone N°2, and location 11 is used to select which partitions are reported to phone N°2.
NX-10 Installers manual Telephone number 3 LOCATION 12 - PROGRAMMING PHONE N° 3 (20 segments, numerical data) Phone N°3 is programmed in location 12. A “14” indicates the end of the phone number. Delays of four seconds can be programmed at any point in the phone number by programming a “13” in the appropriate segment. The system will always wait for a dial tone unless the first digit of the phone number is a “13”; in this case, it will only delay. Tone (DTMF) dialling is default.
10 to stop trying to communicate after the designated number of attempts have been made to phone N°3. If a “2” is programmed in this segment, it will cause the NX-10 to make the dial attempts in increments of two. The first two attempts will be made to phone N°3, the next two attempts to phone N°2, then repeating until the total number of attempts designated in segment 1 is completed. Reporting events to phone number 3 Phone N°3 can be used as a third receiver to multi-report or split report events.
NX-10 Installers manual Special formats LOCATION 18 - CUSTOM COMMUNICATOR FORMAT (see locations 2, 8, and 14) Segment 1 1= 2= 3= 4= 5= 6= 7= 8= On for 1800hz transmit; Off for 1900hz On for 2300hz handshake; Off for 1400hz On for checksum parity; Off for double round parity On for 2 digit event code; Off for 1 digit event code On for extended reporting; Off for non-extended reporting Reserved On for 20 PPS; Off for 10 or 40 PPS On for 10 PPS; Off for 20 or 40 PPS Segment 2 1= 2= 3= 4= 5= 6= 7= 8= On f
LOCATION 21 - DOWNLOAD CONTROL (1 segment, feature selection data) Location 21 contains the feature selections to control download sessions. The following features can be enabled or disabled using this location (see the feature definitions on pages 5-11). Segment 1 1= 2= 3= 4= 5= 6= 7= 8= On: enables two call answering machine defeat Reserved On: requires call-back before download session Shutdown (can only be viewed from the keypad; must be changed by downloading) On: locks all local programming.
NX-10 Installers manual lockout) Segment 2 1= 2= 3= 4= 5= 6= 7= 8= On: enables the LED extinguish feature On: enables the require code for bypassing feature On: enables the zone bypassed sounder alert feature On: enables the AC power/low battery sounder alert feature On: enables bypass toggle On: enables silent auto arm On: enables the automatic instant feature (of entry/exit zones) On: enables final set door Segment 3 1= 2= 3= 4= 5= 6= 7= 8= On: enables opening and closing reports On: enables zone by
Segment 2 Exit time 1 Segment 3 Entry time 2 Segment 4 Exit time 2 Segment 5 Segment 6 Reserved Reserved This is the exit time that will be used for all zones designated as delay 1. Valid entries are 10-255 seconds. This is the entry time that will be used when a delay 2 zone type initiates an entry delay. Valid entries are 10-255 seconds. This is the exit time that will be used for all zones designated as delay 2. Valid entries are 10-255 seconds.
NX-10 Installers manual 12 13 14 15 16 This zone type will arm and disarm the partition or partitions of the control panel where it is resident, every time the zone is shorted. Keyswitch arming will report as User 99 in logs and reports. This zone type can only belong to 1 partition. INTERIOR FOLLOWER WITH “CROSS ZONE” ENABLED This zone will be instant when the system is armed and no entry or exit delay is being timed. It is delayed during entry and exit delay times.
27 28 29 30 Creates an instant audible alarm, regardless of the arming state of the control panel. It will display on the keypad. This zone type will NOT be reported. INSTANT ZONE FORCE ARMABLE This zone creates an instant alarm whenever the system is armed. This zone is force armable (see feature definitions, pages 5-11). INSTANT ZONE ACTIVITY MONITOR ENABLED This zone creates an instant alarm whenever the system is armed.
NX-10 Installers manual 2= 3= 4= Partition 2 Partition 3 Partition 4 LOCATION 29 - ZONES 17-24 CONFIGURATION GROUP (8 segments, numerical data) Location 29 contains the configuration group (zone type) for zones 17-24. Segment 1 is for zone 17, segment 8 is for zone 24. You will find the default configurations in the table above. LOCATION 30 - PARTITION SELECT, ZONES 17-24 (8 segments, feature selection data) Location 30 is used to select the partition(s) in which zones 17-24 reside.
LOCATION 34 - PARTITION SELECT, ZONES 33-40 (8 segments of feature selection data) Location 34 is used to select the partition(s) in which zones 33-40 reside. A zone may reside in any combination of the 4 partitions. If a burglary zone resides in more than 1 partition, that zone will only be active when all partitions are armed. A zone that resides in more than 1 partition will be reported to its lowest partition. Segment 1 corresponds to zone 33 and segment 8 corresponds to zone 40.
NX-10 Installers manual Segment 2 1= Segment 3 1= 2= 3= 4= 5= 6= 7= 8= On: if siren driver should be a voltage output. Off: if on-board siren driver is enabled On: if sirens* sound for expander trouble On: for zones to restore immediately. Off: for zones to restore only when the siren is off or disarmed On: if dynamic battery test is performed at arming.
enabled in location 40. Do not use this feature as the only backup feature of the PSTN dialer but use this in addition with the standard backup options as described in the GSM module manual. LOCATION 38 - SWINGER SHUTDOWN COUNT Location 38 contains the number of trips on a zone before that zone will be automatically bypassed. From 0 to 255. Refer to the feature definitions.
NX-10 Installers manual before you exit from programming 2= 3= 4= 5= 6= 7= 8= On: requires code entry for the perform callback download function and the answer incoming call for download function On: enables Auto Cancel / Abort Reserved On: keypad shutdown mode On: user authorization to enter program mode On: codes 16 and 17 are guard codes Reserved LOCATION 42 - INSTALLER CODE (6 segments, numerical data) Location 42 contains the installer code (“Go To Program” code).
Programming the outputs LOCATION 45 - AUXILIARY OUTPUT 1-2 PARTITION SELECTION (2 segments, feature selection data) Location 45 is used to select the partition(s) in which the events must occur before the output (relay) will activate. Location 45 has 2 segments. Segment 1 corresponds to output 1, and segment 2 corresponds to output 2.
NX-10 Installers manual Data Event 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Fire alarm 24 hour alarm Trouble alarm Tamper alarm Yelping siren Steady siren Any siren Any bypass AC fail Low battery Duress Aux 1 keypad (fire alarm) Aux 2 keypad (medical alarm) Panic keypad Keypad tamper Autotest Alarm memory (solid) Entry Exit Entry or exit Armed state Disarmed state Ready Not ready 25 26 27 28 29 Fire Fire trouble Chime Expander trouble Dynamic battery test time Data 31 32 33 34 3
LOCATION 52 - OPENING TIME/AUTOMATIC DISARMING TIME (2 segments, numerical data) Location 52 contains the time (in 24 hour format) when the NX-10 will enable the disarm capability for codes designated as ‘arm only after closing’. This time is only valid on those days programmed in location 54. This is also the time when the panel will automatic disarm. Note: Opening time must be earlier than closing time so that auto arm, Aux. outputs, or code authorisation can function properly.
NX-10 Installers manual 4= 5= 6= 7= 8= Auto arming on Wednesday Auto arming on Thursday Auto arming on Friday Auto arming on Saturday Disable retry timer Communicator codes for slow speed formats only Note: Locations 56-83 are only used when reporting events to a pager, or when using a slow format such as 4+2. When using Contact ID or SIA, there is no need to program these locations.
Segment 1 Segment 2 Segment 3 Segment 4 Partition 1 Partition 2 Partition 3 Partition 4 “Tamper Code” “Tamper Code” “Tamper Code” “Tamper Code” LOCATION 59 - TROUBLE COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (4 segments, numerical data) Location 59 contains the event code for a zone “Trouble” with a 4+2 and 3+1 format. For the 4+2 format, the digit programmed in this location will be sent as the tens digit of the trouble event code.
NX-10 Installers manual LOCATION 62 - DURESS COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (2 segments, numerical data) Location 62 contains the tens and ones digits that will be sent for a 4+2 and 3+1 format if the duress code is enabled in location 44. Segment 1 contains the tens digit, and segment 2 contains the ones digit. For a 3+1 format, only the segment 1 digit (tens) will be sent.
LOCATION 67 - BOX TAMPER / BOX TAMPER RESTORE COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (4 segments, numerical data) Location 67 contains the tens and ones digits that will be sent for a 4+2 and 3+1 format if the “Box Tamper” feature is enabled in location 37. Segment 1 contains the tens digit of the “Box Tamper”. Segment 2 contains the ones digit of the “Box Tamper”. Segment 3 contains the tens digit of the “Box Tamper Restore”. Segment 4 contains the ones digit of the “Box Tamper Restore”.
NX-10 Installers manual Segment 2 contains the ones digit of the “Bell Tamper Reporting”. Segment 3 contains the tens digit of the “Bell Tamper Restore”. Segment 4 contains the ones digit of the “Bell Tamper Restore”. For a 3+1 format, only the segment 1 resp. segment 3 digit (tens) will be sent.
For a 3+1 format, only the segment 1 digit (tens) will be sent. LOCATION 77 - OPENING COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (8 segments, numerical data) Location 77 contains the tens digit for a 4+2 and 3+1 format if “Opening Reporting” is enabled. The ones digit is the ones digit of the user number that did the opening. If the user is greater than 9, the numbers will begin repeating (e.g. code 6 = 6, code 45 = 5). This location contains 8 segments.
NX-10 Installers manual LOCATION 80 - RECENT CLOSING AND EXIT ERROR COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY (2 segments, numerical data) Location 80 contains the tens digit for a 4+2 and 3+1 format that will be sent if “Recent Closing” and/or “Exit Error Reporting” is enabled. Segment 1 contains the tens digit for the “Recent Closing Reporting”. Segment 2 contains the tens digit for the “Exit Error Reporting”. The ones digit is the ones digit of the user number that did the opening.
LOCATION 84 - BUS FAULT AND BUS FAULT RESTORE COMMUNICATOR CODES, SLOW SPEED FORMATS ONLY (4 segments, numerical data) Location 84 contains the tens and ones digits for a 4+2 and 3+1 format that will be sent if “Short circuits and ground faults” reporting is enabled. Segment 1 contains the tens digit of the “Bus Fault Reporting”. Segment 2 contains the ones digit of the “Bus Fault Reporting”. Segment 3 contains the tens digit of the “Bus Fault Restore”.
NX-10 Installers manual LOCATION 91 - PARTITION 2 ENTRY EXIT TIMERS (6 segments, numerical data) Location 91 is used to enter the entry and exit times, in seconds. There are 2 separate entry and exit times. Valid entries are 10-255 seconds. If all the segments are “0”, the entry and exit times for partition 1 will be used.
LOCATION 95 - ACCOUNT CODE FOR PARTITION 4 (6 segments, numerical data) The account code that is sent when reporting partition 4 is programmed in location 95. If location 95 is left unprogrammed (all “10”) then the account code corresponding to the phone number that is dialled will be used. If the account code is less than six digits, program a “10” in the segment immediately after the last digit of the account code. If the account code is 6 digits long, program all 6 segments.
NX-10 Installers manual LOCATION 111 - CONFIGURATION GROUP 1 CHARACTERISTIC SELECT (5 segments, feature selection data) Segment 1 1= 2= 3= 4= 5= 6= 7= 8= Segment 2 Segment 3 Segment 4 Segment 5 (*) Note: 1= 2= 3= 4= 5= 6= 7= 8= 1= 2= 3= 4= 5= 6= 7= 8= 1= 2= 3= 4= 5= 6= 7= 8= 1-8 Fire (turn on if this is a fire zone) 24 hour (turn on for non-fire 24 hour zones) Keyswitch zone (normally open switch) Follower (turn on for burglary zones that are Instant during non-entry times) Delay 1 zone (follows tim
LOCATION 113 - CONFIGURATION GROUP 2 CHARACTERISTIC SELECT (5 segments, feature selection data) Use the “Configuration Group Characteristic Selections” described in Location 111. LOCATION 114 - CONFIGURATION GROUP 3 ALARM EVENT CODE (1 segment, numerical data) Location 114 contains the event code that is sent for a Contact ID or SIA report. The desired event code should be chosen from the Table 38 or Table 39 in Appendix 1. The zone ID will be the zone that is in alarm.
NX-10 Installers manual LOCATION 119 - CONFIGURATION GROUP 5 CHARACTERISTIC SELECT (5 segments, feature selection data) Use the “Configuration Group Characteristic Selections” described in Location 111. LOCATION 120 - CONFIGURATION GROUP 6 ALARM EVENT CODE (1 segment, numerical data) Location 120 contains the event code that is sent for a Contact ID or SIA report. The desired event code should be chosen from the Table 38 or Table 39 in Appendix 1. The zone ID will be the zone that is in alarm.
LOCATION 125 - CONFIGURATION GROUP 8 CHARACTERISTIC SELECT (5 segments, feature selection data) Use the “Configuration Group Characteristic Selections” described in Location 111. LOCATION 126 - CONFIGURATION GROUP 9 ALARM EVENT CODE (1 segment, numerical data) Location 126 contains the event code that is sent for a Contact ID or SIA report. The desired event code should be chosen from the Table 38 or Table 39 in Appendix 1. The zone ID will be the zone that is in alarm.
NX-10 Installers manual LOCATION 131 - CONFIGURATION GROUP 11 CHARACTERISTIC SELECT (5 segments, feature selection data) Use the “Configuration Group Characteristic Selections” described in Location 111. LOCATION 132 - CONFIGURATION GROUP 12 ALARM EVENT CODE (1 segment, numerical data) Location 132 contains the event code that is sent for a Contact ID or SIA report. The desired event code should be chosen from the Table 38 or Table 39 in Appendix 1. The zone ID will be the zone that is in alarm.
code should be chosen from the Table 38 or Table 39 in Appendix 1. The zone ID will be the zone that is in alarm. This location is not used for slow speed formats (like 4+2 and 3+1). This location may also contain the alarm report code for the Robofon format (value 00-99). LOCATION 137 - CONFIGURATION GROUP 14 CHARACTERISTIC SELECT (5 segments, feature selection data) Use the “Configuration Group Characteristic Selections” described in Location 111.
NX-10 Installers manual LOCATION 142 - CONFIGURATION GROUP 17 ALARM EVENT CODE (1 segment, numerical data) Location 142 contains the event code that is sent for a Contact ID or SIA report. The desired event code should be chosen from the Table 38 or Table 39 in Appendix 1. The zone ID will be the zone that is in alarm. This location is not used for slow speed formats (like 4+2 and 3+1). This location may also contain the alarm report code for the Robofon format (value 00-99).
LOCATION 148 - CONFIGURATION GROUP 20 ALARM EVENT CODE (1 segment, numerical data) Location 148 contains the event code that is sent for a Contact ID or SIA report. The desired event code should be chosen from the Table 38 or Table 39 in Appendix 1. The zone ID will be the zone that is in alarm. This location is not used for slow speed formats (like 4+2 and 3+1). This location may also contain the alarm report code for the Robofon format (value 00-99).
NX-10 Installers manual LOCATION 153 - CONFIGURATION GROUP 22 CHARACTERISTIC SELECT (5 segments, feature selection data) Use the “Configuration Group Characteristic Selections” described in Location 111. LOCATION 154 - CONFIGURATION GROUP 23 ALARM EVENT CODE (1 segment, numerical data) Location 154 contains the event code that is sent for a Contact ID or SIA report. The desired event code should be chosen from the Table 38 or Table 39 in Appendix 1. The zone ID will be the zone that is in alarm.
This location is not used for slow speed formats (like 4+2 and 3+1). This location may also contain the alarm report code for the Robofon format (value 00-99). LOCATION 159 - CONFIGURATION GROUP 25 CHARACTERISTIC SELECT (5 segments, feature selection data) Use the “Configuration Group Characteristic Selections” described in Location 111. LOCATION 160 - CONFIGURATION GROUP 26 ALARM EVENT CODE (1 segment, numerical data) Location 160 contains the event code that is sent for a Contact ID or SIA report.
NX-10 Installers manual LOCATION 164 - CONFIGURATION GROUP 28 ALARM EVENT CODE (1 segment, numerical data) Location 164 contains the event code that is sent for a Contact ID or SIA report. The desired event code should be chosen from the Table 38 or Table 39 in Appendix 1. The zone ID will be the zone that is in alarm. This location is not used for slow speed formats (like 4+2 and 3+1). This location may also contain the alarm report code for the Robofon format (value 00-99).
LOCATION 169 - CONFIGURATION GROUP 30 CHARACTERISTIC SELECT (5 segments, feature selection data) Use the “Configuration Group Characteristic Selections” described in Location 111. LOCATIONS 170-205 - RESERVED LOCATION 206 – AUTO DISARM DAY SELECTOR (4 segments, feature selection data) Location 206 selects which days each partition will auto disarm. Segment 1 is for partition 1 and segment 4 is for partition 4.
NX-10 Installers manual 5 Spain 6 Greece 7 South Africa 8 Israel 9 Spain (PRSGR) 10 Turkey 11 France 17 Turkey Pronet 50 US 129
NX-10 location-programming worksheets Factory defaults for NX-10 are in bold italic text. These defaults are for the country code 2 (Belgium/Poland).
NX-10 Installers manual 3 4 12 13 14 15 16 17 Partition 3 Partition 4 14-14-14-14-14-14-14-14-1414-14-14-14-14-14-14-14-1414-14 10 – 10 – 10 – 10 – 10 – 10 PHONE 3, ACCOUNT CODE 0 PHONE 3, REPORTING FORMAT 8 PHONE 3, DIAL ATTEMPTS 0 BACKUP CONTROL PHONE 3, SELECTING EVENTS TO REPORT TO PHONE 3 Segment 1 (Circle Numbers To Program) Segment 2 (Circle Numbers To Program) 1 Alarms 1 Tampers (zones and box) 2 Open/Close 2 Short Circuit 3 Bypass 3 Sensor Lost 4 Zone Trouble 4 Sensor Low Battery 5 Power Troub
4 5 6 7 8 Shutdown control panel Lock out local programming Lock out communicator programming Lock out download section Enables callback at autotest interval 22 CALLBACK PHONE NUMBER 23 PARTITION 1, FEATURE SELECTION Segment 1 1 Quick Arm 1 2 Re-Exit 2 3 4 5 6 7 8 24 25 26 27 28 14-14-14-14-14-14-14-14-1414-14-14-14-14-14-14-14-1414-14 Segment 2 LED extinguish enable Require user code for bypassing zones Bypass sounder alert AC power/ low battery sounder alert Enables bypass toggle Enables silent
NX-10 Installers manual 29 30 31 32 33 34 35 36 37 Partition 2 2 2 2 2 2 2 Partition 3 3 3 3 3 3 3 Partition 4 4 4 4 4 4 4 6-6-6-6-6-6-6-6 ZONES 17-24, CONFIGURATION GROUPS ZONES 17-24, PARTITION SELECTION (Segment 1=Zone 17 thru Segment 8=Zone 24) Segments 1 2 3 4 5 6 Partition 1 1 1 1 1 1 1 Partition 2 2 2 2 2 2 2 Partition 3 3 3 3 3 3 3 Partition 4 4 4 4 4 4 4 6-6-6-6-6-6-6-6 ZONES 25-32, CONFIGURATION GROUPS ZONES 25-32, PARTITION SELECTION (Segment 1=Zone 25 thru Segment 8=Zone 32) Segments 1 2 3
2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 37 1 2 1-8 38 39 AC Fail report enabled Low Battery report enabled Auxiliary power overcurrent report enabled Siren supervision report enabled Restore Telephone Line Cut report enabled A+B alarm Expander trouble report enabled Segment 4 (Circle Numbers To Program) Failure To Communicate report enabled Log Full report enabled Autotest report enabled Start and End Programming report enabled End Download report enabled Sensor Low Battery report e
NX-10 Installers manual 40 41 SYSTEM TIMERS Segment 1 Dynamic Battery Test duration (0-30 minutes) Segment 2 AC Failure report delay (0-255 minutes) Segment 3 Power Up Delay (0-60 seconds) Segment 4 Siren Time (1-255 minutes) Segment 5 Telephone Line Cut delay (0-255 seconds) Segment 6 Cross Zone Time (0-255 minutes) Segment 7 Chime Time in 50 ms increments (0-255) Segment 8 Dialer delay (0-255 seconds) Segment 9 Fire Alarm Verification Time (120-255 seconds) Segment Listen-In Time (0-255 seconds) 10 Segm
45 46 47 48 51 52 53 54 AUXILIARY OUTPUTS 1-2 PARTITION SELECTION Segments 1 Partition 1 1 Partition 2 2 Partition 3 3 Partition 4 4 AUXILIARY OUTPUTS 1-2 SPECIAL TIMING Segments Auxiliary output timed in minutes Auxiliary output to latch Auxiliary output to stop timing when user code is entered Auxiliary output to activate only between closing and opening time Auxiliary output to activate only between opening and closing time Invert auxiliary output (0 volts going to 12 volts when activated) Reserv
NX-10 Installers manual Saturday Reserved 55 56 57 58 59 60 61 62 63 64 65 7 8 7 8 7 8 7 8 DAYS OF THE WEEK WHEN “AUTO ARMING” WILL OCCUR IN PARTITIONS 1-4 Segments 1 2 3 Sunday 1 1 1 Monday 2 2 2 Tuesday 3 3 3 Wednesday 4 4 4 Thursday 5 5 5 Friday 6 6 6 Saturday 7 7 7 Disable 8 8 8 retry RESTORE COMMUNICATOR CODE, SLOW SPEED FORMATS ONLY Segment 1 Partition 1 restore code Segment 2 Partition 2 restore code Segment 3 Partition 3 restore code Segment 4 Partition 4 restore code BYPASS COMMUNICAT
66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 8587 88 PARTITION 1, ACCOUNT CODE 89 PARTITION 2, ACCOUNT CODE 90 PARTITION 2, FEATURE SELECTION Segment 1 1 Quick Arm 1 2 Re-Exit 2 91 0-0 0-0-0-0 0-0-0-0 0-0-0-0 0-0-0-0 0-0-0-0 0-0-0-0 0-0 0-0-0-0 0-0 0-0 KEYPAD MULTIPLE CODE ENTRY TAMPER BOX TAMPER / BOX TAMPER RESTORE AC FAIL / AC RESTORE LOW BATTERY / LOW BATTERY RESTORE POWER SHORT / POWER SHORT RESTORE BELL TAMPER / BELL TAMPER RESTORE TELEPHONE LINE CUT RESTORE Reserved EXPANDER TR
NX-10 Installers manual Segment 1 Segment 2 Segment 3 Segment 4 Reserved Reserved (Entry Time 1) (Exit Time 1) (Entry Time 2) (Exit Time 2) 92 PARTITION 3, ACCOUNT CODE 93 PARTITION 3, FEATURE SELECTION Segment 1 1 Quick Arm 1 2 Re-Exit 2 94 0 0 0 0 0 0 10-10-10-10-1010 Segment 2 Segment 3 LED extinguish enable 1 Open/Close Require user code for bypassing 2 Bypass zones 3 Auto Bypass (interior) 3 Bypass sounder alert 3 Restore 4 Silent Panic 4 AC power/ low battery sounder alert 4 Trouble 5 Audible
97 110 111 3 Enables instant night 4 Tamper when sensor lost if armed 5 Enables instant stay toggle 6 Arming with tamper mem./ comm.
NX-10 Installers manual 0-125-25678 0 2-5-278 1 1-13-378 7 6-125-25678 13 24-12-78 3 3-0-2 5 457-125-245678 4 0-1258-25678 7 5-1256-25678 5 457-1256-25678 4 0-1256-25678 3 38-0-2 7 5-1257-25678 7 6-1257-25678 7 5-1245-25678 20 24-125-278 20 24-5-278 5 7-125-25678 4 0-1245-25678 5 45-1245-25678 3 248-125-2 4 0-1257-25678 4 0-125-25678-1 4 0-125-5678-2 11 24-125-278 0-0-0-0-0-0-0-0 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152
Segments Sunday Monday Tuesday Wednesday Thursday Friday Saturday Reserved 1 1 2 3 4 5 6 7 8 2 1 2 3 4 5 6 7 8 207211 RESERVED 212 213 LCD KEYPAD ADDRESS FOR XSIA ZONE DESCRIPTIONS COUNTRY CODE 3 1 2 3 4 5 6 7 8 4 1 2 3 4 5 6 7 8 192 0
NX-10 Installers manual Chapter B3 Programming the NX-1048 keypad Overview Each NX-1048 keypad has a sounder and an LCD display that displays messages in a number of possible languages. Each NX-1048 keypad must be enrolled, defaulted to the country settings for the selected country and defaulted to the factory defaults before starting to program the system. For more information on enrolling and defaulting, see Chapter B7 Enrolling modules.
Figure 21. NX-1048 keypad menu 3.2 Keypad Number Partition Nbr 3.3 Keypad Features 3.1 3.3.12 Case Tamper Silent Keypad Ding-Dong Chime 5 sec silence Armed Zone Info Beep on Panics Master keypad Service Message Custom Message Custom Msg.Lock Clock 24-hour Clock 3.3.13 Advanced Options 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 3.3.8 3.3.9 3.3.10 3.3.11 3.3.13.6 Type OK for Menu LED Extinguish Hide PINs Beep on RF loss Always Master mode User Phone Editing 3.3.13.7 Buzzer On Exit 3.3.13.1 3.3.
NX-10 Installers manual Configuring the NX-1048 keypad features General options You can configure the LCD display, the keypad sounder and combination keys. The following example configures the keypad so that all codes are displayed as stars rather than in digits. It also configures the keypad sounder to beep when a wireless receiver does not report within the supervision window. 1. Navigate with the ½¾ keys to This Keypad>Keypad Features and press OK. 2. Scroll to Display>Hide PINs>Yes and press OK. 3.
the Arm Away function works as a single-button shortcut only in the single-partition mode if the Installer Menu>Control Panel>Partition Settings>Partition 1>Feature Select>Arming>Quick Arm menu option was set. Some functions are assigned to particular keys by default, and can be made permanent (fixed) at the factory. Note: When arming the system with a function key, both logs and reports show User 98 as the user who armed the system. There are the following default key assignments: Table 14.
NX-10 Installers manual user code. Disarming the system clears the bypassed zone set. Group Bypass Automatically bypasses all the zones with the Group Bypass attribute set (for example, Interior Follower with Group Bypass Enabled zone type). It is a shortcut for the User Menu>Group Bypass menu option. To cancel Group Bypass function press the button again. To partially arm the system with the selected zones bypassed, enter the user code. Disarming the system clears the bypassed zone set.
removed from its wall mounting plate. The option Always Tamper actually fixes the wireless keypad to the wall just like a wired one, while disabling this option renders the keypad fully portable within the reach of the RF link. An additional option Only Arm AWAY if On the Wall ensures that the keypad is always mounted onto its bracket before arming in the Away mode. Both these options together ensure that the keypad will stay on the wall as long as the system is armed.
NX-10 Installers manual Backlight battery replacement 1. Push the battery compartment cover in a direction indicated by the arrow symbol on the cover. 2. Open the backlight battery compartment and replace batteries. Operating battery replacement The master user is allowed to perform the operating battery replacement according to the following procedure. 3. Disarm the system. 4. Press OK and enter your master user code to open the User Menu. 5.
6. Open the backlight battery compartment as described above. 7. Unscrew two screws inside the backlight battery compartment as shown below. 8. Open the operating battery compartment and replace all four batteries. You have 5 minutes to finish this operation. You must use Duracell or Energizer "AA" batteries only. 9. After replacing batteries, you have to close the battery compartment in 30 seconds. 10.
NX-10 Installers manual operation. CAUTION: Batteries can explode or cause burns when recharged, incorrectly (dis)assembled, or exposed to fire or high temperatures. Dispose of used battery according to battery directive instructions and/or as required by local laws. Keep away from children. Only replace the batteries with Energizer or Duracell AA batteries. Do not use a different type of batteries.
2. Select the relevant partition number and press OK. 3. Select the number of the keypad to which the settings will be copied and press OK. 4. The keypad displays the message Copying while copying the settings and returns to Keypad # when copying is complete. Note: In case of wireless keypads, settings are copied from the keypad to the RF receiver first and then sent to the target keypad (or one-by-one to consecutive keypads).
NX-10 Installers manual 2. Select Program KP Text, press OK, and then select a language using the ½¾ keys. 3. Scroll to Zones/Messages>Custom Message, press OK, and then edit the appropriate line of the message. 4. Press OK. The keypad beeps once to accept the change and returns to Custom Message. Edit the other line of the message, if required.
9. Scroll to Keypad Features>Advanced Options>Buzzer On Exit>Exit Time 1. 10. Use the ½¾ keys to change the status to enabled and press OK. 11. The keypad beeps once to accept the change and returns to Exit Time 1. 12. Scroll to Keypad Features>Advanced Options>Buzzer On Exit>Exit Time 2. 13. Use the ½¾ keys to change the status to disabled and press OK. 14. The keypad beeps once to accept the change and returns to Exit Time 2.
NX-10 Installers manual Location Term Definition 3.2 Partition Number A menu entry menu option that specifies the partition that the selected keypad can access if it is a single-partition keypad. Together with the keypad number, it determines the keypad bus module number for both single-partition and master keypads. 3.3 Keypad Features A menu entry that groups keypad options. 3.3.
Location Term Definition system, i.e. all keypads always display the same message. 3.3.11 Clock A menu option that displays the clock on the keypad. This is the internal real time clock used for the schedules and autotest intervals. 3.3.12 24-hour Clock A menu option that switches between 24-hour and 12hour notation. 3.3.13 Advanced Options A menu entry that groups LCD display options for the keypad. 3.3.13.1 Type OK for Menu A menu option that enables the menu prompt ‘Type OK for Menu’. 3.3.
NX-10 Installers manual Location Term Definition 3.3.13.8.1 Unit Code A menu option that sets the X-10 unit code used to identify a particular X-10 device on the selected module. 3.3.13.8.2 House Code A menu option that sets the code used to identify a particular premises. It is necessary in case any neighbouring premises also has an X-10 home automation system. More information on the X-10 home automation system can be found at www.x-10europe.com. 3.3.13.
Location Term Definition 3.5 Set KP Language A menu option that selects the keypad interface languages available to the user. It is possible to select up to four languages (Language 1 to 4) out of all available interface languages. The languages selected here, can be then toggled by the user (or installer) with the OK key. 3.6 Program KP Text A menu entry that groups the language options of the current keypad. It allows the installer to set options such as zone name descriptors and user names. 3.6.
NX-10 Installers manual Location Term Definition 3.9 Reset Settings A menu option that defaults the keypad to factory defaults. 3.10 Diagnostics A menu entry that groups the wireless keypad options related to keypad's diagnostics, like good packet count, last bad packet, etc. 3.11 Model A menu option that displays the current model of the keypad. 3.12 Version A menu option that displays the current software version of the keypad. 3.
Shipping weight 441 g NX-1048-W LCD keypad (wired) Power supply specifications Power supply voltage 9 V … 14.4 V Current consumption – backlight ON, buzzer ON 35.0 mA at 13.8 V ± 5% Current consumption – backlight ON, buzzer OFF 28.9 mA at 13.8 V ± 5% Current consumption – standby 13.8 mA at 13.8V ± 5% ± 2% General feature specifications PCB Size Dimensions (width x height x depth) 158 x 88 x 1.
NX-10 Installers manual Chapter B4 Programming the other keypads Figure 22. Other keypads menu 4.1 (1) Partition 1 Keypad 1 4.1.1.1 Keypads 2 - 4 Same as above 4.1.1.2 4.1.1 Partitions 2 - 4 Same as above 4.1.1.3 Model Version Reset Settings This menu branch is obsolete in the NX-10 system. It gets displayed for older systems only. To program other keypads, select Installer Menu>Other Keypads and select the partition containing the keypad.
Chapter B5 Setting up the RF receivers Programming the RF system Figure 23. RF menu 5.1 RF Receiver 32 5.1.1 Start Zone * For additional 868 RF receivers only RF Receivers 33 - 39 Same as above 5.1.2 Learn RF Device Del. RF Device 5.1.3 5.1.4 RSSI RF Device 5.1.2.1 Learn RF Zone 5.1.2.1.1 (1) Zone 1 5.1.2.2 Learn RF Keypad 5.1.2.1.1 RF Keypad 1 5.1.2.3 Learn RF Sir/IO 5.1.2.1.1 RF Siren/IO 1 5.1.2.4 Sequential Programming 5.1.3.1 Del. RF Zone 5.1. 3.1.1 RF Zone 1 5.1.3.2 Del.
NX-10 Installers manual The built-in wireless receiver of the NX-10 is compatible with wireless sensors and keyfobs of the type 868MHz Generation 2 only. Existing receivers (868MHz FM and 433MHz AM) can also be connected to the NX-10 databus. The NX-10 built-in receiver is enrolled as module 32. Defaulting the wireless modules You must enrol and default each RF receiver before you begin programming the system. 1. Navigate with the ½¾ keys to RF Receivers and press OK. 2.
Transmitter Action Fire detector Press and hold the test button. Note: Some fire detectors require activating the tamper switch instead. See the detector manual for exact instructions. Note: If installer wants to replace a fire sensor (the zone type is set to Fire) then the installer at the beginning should change the zone type to the other type, delete the sensor, learn-in and mount a new sensor, and then set up back the Fire zone type. Two Button Panic Press and hold the two buttons together.
NX-10 Installers manual Note: If the wireless keypad is not brand new (i.e. it was already used with another system), it must be reprogrammed (flashed) first to erase any previous keypad settings, otherwise it will not initialize the learning mode (see Chapter B11 Updating firmware on page 242). 5. On the new keypad, select a language from the list with the ½¾ keys and press OK. 6. Select default settings from the Load Country Defaults list with the ½¾ keys and press OK. 7.
memory. Note: You cannot delete the currently used wireless keypad (the one used for programming). Note: After deleting the wireless keypad, you have to default it to clear any existing settings. To do this, press F1+6+Down Arrow simultaneously for a few seconds. The wireless keypad can only be brought back to defaults (to initiate the startup process) if it is not in the range of an active NX-10 panel, i.e. the signal strenght icon must show X.
NX-10 Installers manual second and maximum of 5 seconds, and release the tamper again. 7. The LED on the IO module will blink for 1 second, and the keypad beeps once to confirm the siren is programmed. 8. The siren is learned-in. Insert the batteries powering the siren, if necessary, and close the siren housing. Any new IO module is learned-in by default as a universal siren, i.e. its both outputs are triggered by the Any Siren event and timing is set to 3 minutes.
3. Select Event>Not Ready to Arm and press OK. 4. The keypad beeps once to accept the change and returns to Event. 5. Navigate with the ½¾ keys to Time Unit and press OK. Select Minutes and press OK. 6. The keypad beeps once to accept the change and returns to Time Unit. 7. Navigate with the ½¾ keys to Time, enter 6 and press OK. 8. The keypad beeps once to accept the change and returns to Time. 9. Navigate with the ½¾ keys to Partitions and press OK. Select partition 1 only and press OK. 10.
NX-10 Installers manual IO modules can be also triggered by keyfob buttons. This way you can turn on and off some external device or activate a wireless siren. To do this you must activate the switch output functionality for the keyfob, and correctly set the event triggering the selected output on the particular IO module. The following example configures the button 1 on the keyfob (light bulb button), to allow it to toggle the output 1 on the I/O module 4 ON and OFF.
7. Select Enabled and press OK. 8. The keypad beeps once to accept the change and returns to Antipassivation. Recommended settings depend on the type of application the IO module is used for, and are as follows: Application Outdoor Siren Indoor Siren Standalone IO module Low Battery Trip Antipassivation Operational battery 3.0 V Enabled Siren battery 9.8 V Operational battery 2.3 V Siren battery 9.0 V Operational battery 2.
NX-10 Installers manual • Values between 90 and 80: These are low values but the sensor will still work properly. • Values between 80 and 50: These are normal working values for sensor located at a longer distance from the receiver. • Values smaller than 50: Perfect conditions. RSSI Values may change due to environmental circumstances, for example, additional furniture or metal constructions. The following example tests the RSSI value of zone 2 on receiver 32. 1.
Term Definition seconds in order to improve the siren's battery life. Attributes A menu entry that groups additional configuration options for IO modules. Code Stops Timer A menu option that specifies the way entering code by the user affects the way the output is timed. If set to Yes, the output should be reset if a code is entered while it is being timed. When set to No, the output stays timed (not reset) after a code is entered.
NX-10 Installers manual Term Definition Internal Reed A menu option on an RF door/window sensor that enables the internal reed contact. Jam Detection A menu option that enables the detection of RF jamming. Keyfob A menu entry that groups options relating to any device that sends commands by a wireless receiver. Keyfob Disarming When this option is set to Normal (loc 193 bit 6) user can arm and disarm using keyfob buttons.
Term Definition keyfob function 2 (see below). Option 3 A menu option used for configuring a sensor. For actual setting description, see the particular sensor manual. Output Latched A menu option that specifies the way the output is timed. If set to Yes, the output will latch until a code is entered. When set to No, the output is timed according to Time setting.
NX-10 Installers manual Term Definition Smoke A menu entry that groups smoke sensor options. Start Zone A menu option that specifies the first zone number of zones on the RF receiver. Note: In case of the RF Receiver 32 (the NX-10 built-in 868MHz Gen2 receiver), this option is not visible. In the NX-10 system, you can set this value for additional RF receivers only. For the receiver 32 the starting zone is always zone 1. Supervised A menu option that enables supervision of the selected RF sensor.
Term Definition option is set to Disabled, keypads do not wake up, and chime is not emitted. Please note, that also other keypad settings can affect whether the acoustic signal is actually emitted or not, for example, Keypad Features>Silent Keypad. X-10 Address A menu entry that groups X-10 configuration options for IO modules. Zone/User Selects the zone or user number necessary to trigger an output.
NX-10 Installers manual Output Location 81 82 5 83 84 85 6 86 87 88 7 89 90 91 8 92 93 Segment Type Description 2 option Partition 1 hex value X-10 unit code 2 hex value X-10 house code 1 dec value Event number 2 dec value Zone / user number 3 dec value Time 1 option Special configuration 2 option Partition 1 hex value X-10 unit code 2 hex value X-10 house code 1 dec value Event number 2 dec value Zone / user number 3 dec value Time 1 option Special co
zones for all these events), and Code Entry (it filters out users). For all other events this setting is ignored. Segment 3 - Time Selects the amount of time an output will remain activated when an output triggers. If this location is programmed as a zero, the output will follow the particular event.
NX-10 Installers manual Segment 2 - House code Program a number from 0-15 to represent the corresponding house code from the following table. X-10 Location code (house code) 0=A 4=E 8=I 12=M 1=B 5=F 9=J 13=N 2=C 6=G 10=K 14=O 3=D 7=H 11=L 15=P LOCATIONS 150-159 - AUTHORIZING USERS 1 - 99 TO TRIGGER OUTPUTS 1 - 8 (10 segments, feature selection data) When activating outputs with a user code (event 45), locations 150-159 can be used to restrict certain codes from activating certain outputs.
Chapter B6 Setting up the GSM/GPRS module (NX-7002) Overview In case you want to add GSM/GPRS functionality to the panel, you need to use an NX-10 model which has the GSM/GPRS on-board or you need to add a separate NX-7002 module. Only one GSM/GPRS module can be used and will have module number 78. The GSM/GPRS module features include: • Wireless event reporting. • 12 configurable report destinations. • Selectable reportable events from four partitions. • Compatible with PSTN or ISDN reporting.
NX-10 Installers manual 1. Press OK at the system prompt and enter your installer code. 2. Navigate with the ½¾ keys to Enrol Modules>Enrol and press OK. 3. The keypad starts enrolling the modules. The Enrolling Modules message is displayed while enrolment is taking place (approximately 12 seconds). 4. When the modules have been enrolled, a beep sounds and the message disappears. 5. To verify the enrolled modules, navigate with the ½¾ keys to Maintenance Mode and press OK. 6.
Inserting a SIM card " ! Bus Err GPRS SIM Acti e Err Reportin g PSU Err GSM in Use OPEN OPEN OPEN LOCK LOCK 1 2 3 4 5 LOCK $ # OPEN OPEN LOCK LOCK % & OPEN OPEN LOCK LOCK CAUTION: You must be free of all static electricity when handling electronic components. 1. Power down the system before inserting the SIM Card. 2. Locate the SIM card holder ! on the board. 3. Open the SIM card holder by sliding the clip as shown in " and lifting the holder. 4. The SIM card holder opens #. 5.
NX-10 Installers manual 183 Testing the RSSI value During the enrolling procedure, it is mandatory to check the RSSI value (signal strength) of the NX7002 and record it in the system documentation. The RSSI value is linked to the signal level of the GSM network and ranges from 0-31, with 99 as unknown. The RSSI value may change due to environmental circumstances, for example, additional furniture or metal constructions. If an RSSI reading is not satisfactory, move the antenna to get a better reception.
• The GPRS LED indicates that the module is connected to the GPRS network. This LED turns off when the module is no longer connected to the GPRS network, for example, when it uses the voice channel or CSD. • The REP LED indicates that TCP/SMS reporting is taking place. • The PSU ERR LED indicates that there is a problem with the 3.8 V Switched Mode Power Supply Unit (the modem power source is too low). • The GSM LED indicates that the module is using the CSD channel.
NX-10 Installers manual 185 Programming the GSM/GPRS module (NX-7002) Figure 24. NX-7002 menu structure 15.1 Reporting 15.1.1 Report Control (1) Report 1 15.1.1.1 Reports 2 - 6 Same as above 15.1.1.1.1 15.1.1.1.2 Destination Backup Destination 15.1.1.1.3 Events 15.1.1.1.3.1 Arm/Disarm/Alarm 15.1.1.1.3.1.1 15.1.1.1.3.1.2 15.1.1.1.3.1.3 15.1.1.1.3.2 Tamper/Fault 15.1.1.1.3.2.1 15.1.1.1.3.2.2 15.1.1.1.3.2.3 15.1.1.1.3.2.4 15.1.1.1.3.2.5 15.1.1.1.3.2.6 15.1.1.1.3.3 Power 15.1.1.1.3.3.1 15.
You must enrol and default the GSM/GPRS module before you begin to program the system. For more information on enrolling and defaulting, see Enrolling the system modules on page 223. To program the GSM/GPRS module, select Installer Menu>NX-7002 Module. Programmable options You can program the module using a keypad or DL900 software. You can select the following: • The reporting format to be used. • The reporting destination. • The reporting connection parameters. • The reportable event selections.
NX-10 Installers manual Module>Reporting>Report Control). For example, if the particular partition event, like Opening/Closing, is to be reported, it must be enabled at both Control Panel>Communications>Reporting>Partition Rprt>Opening/Closing and at NX-7002 Module>Reporting>Report Control>Events>Opening/Closing. The same applies to system reports, like Box Tamper, Programming or Expander Trouble. HomeText HomeText is a new report protocol that sends an SMS message of reported events to a telephone number.
Report methods SMS You can send reports by SMS in SIA, XSIA, and Contact ID report formats. You can configure one event list for each report destination. TCP/IP You can send reports by TCP/IP in SIA, XSIA, and Contact ID report formats. You can configure one event list for each report destination Report controllers The GSM/GPRS module contains six report controllers. You can configure the events to be reported and specify two reporting destinations for each report controller.
NX-10 Installers manual as a reporting device if the primary reporting device fails. You should: • Navigate with the ½¾ keys to NX-7002 Module>Reporting>Report Control>Report n>Backup Destination and press OK. • Ensure the reporting format on the reporting device is the same as that set on the GSM/GPRS module. Secondary Reporting The GSM/GPRS module acts as backup for another dialer. It reports the event when the control panel or other dialer fails to report.
Control panel/ GSM/GPRS module as backup for the GSM/GPRS module Backup reports are sent when the GSM/GPRS module fails to send primary reports. Backup reports can be sent by another report control on the module or by another device on the system. Other report control of the GSM/GPRS module as backup • Set a report control to Report When>Report Always.
NX-10 Installers manual Setting up polling You can set up the GSM/GPRS module to report periodically to a receiver that it is still active. This is known as polling. Polling is more frequent than a daily test call but less frequent than continuous monitoring. If you configure a very short polling time, polling occurs very frequently and can generate large quantities of data.
connection type and must be done before the phone number and IP address can be programmed. 2. Navigate with the ½¾ keys to NX-7002 Module>Up/Download>IP Address and press OK. 3. Press #¾ to clear the current value. 4. Enter the IP Address and press OK. 5. Navigate with the ½¾ keys to NX-7002 Module>Options>Network>Port Numbers>U/D Port and press OK 6. Select the U/D port and press OK.
NX-10 Installers manual Report type Information required 193 Menu Option Destination Select NX-7002 Module>Reporting>Report Control>Report n>Destination>SMS1 or SMS 2. Protocol Select NX-7002 Module>Reporting>SMS Reporting>Receiver n>Protocol. Select SIA Separate, SIA Combined or SIA Partition Modified. XSIA over TCP/IP reporting SMS Service Centre Select NX-7002 Module>Options>GSM>SMS Service Center Address.
Report type HomeText Control Information required User code When HomeText control is enabled, you can control your alarm system by sending SMS text messages from your mobile phone. Note: Menu Option User Menu>Users>User n>User Code Note: In order to be recognized by the system, every HomeText user must have a valid user code configured in the control panel, otherwise the system will not accept a command.
NX-10 Installers manual Report type Information required TCP/IP Alarm Port 195 Menu Option Select NX-7002 Module>Options>Network>Port Numbers>TCP/IP Alarm Port. This should match the port number on the receiver side. TCP/IP reporting Status Check Select NX-7002 Module>Options>Status Check>GSM Connection>GPRS Connected. Destination Select NX-7002 Module>Reporting>Report Control>Report n>Destination>TCP/IP 1 or 2.
Information required Report type Protocol Menu Option Select Installer Menu>Control Panel>Communication>Central Station>Phone Numbers>Phone Number n>Protocol. Note: Backup Use any of the panel protocols (SIA, ContactID). Select Installer Menu>Control Panel>Communication>Phone Number >Phone Number n>Events>Communications>Test Reports. Note: Use GSM reporting as backup. Using the GSM/GPRS module This section provides information on using the GSM/GPRS GPRS module.
NX-10 Installers manual 197 Message Description Bus Power Fault There is a problem with the 13.8 V voltage supplied by the bus to the module. Troubleshooting Table 23. Troubleshooting problems and solutions Problem Caused by Do this The module is not sending messages. The antenna is faulty or missing. Ensure the antenna is attached. Replace the old or faulty antenna. The SIM PIN Accepted message is off. The module provides GSM modem information but no GSM operation works.
Report Contact ID SIA Report Contact ID SIA Manual test 601 RX Keypad tamper 137 TA Autotest 602 RP Keypad panic (audible) 120 PA Open (user number) 401 OP Keypad panic (silent) 121 HA Close (user number) 401 CL Duress 121 HA Cancel (user number) 406 OC Keypad auxiliary 1 110 FA Download complete 412 RS Keypad auxiliary 2 100 MA Start program 627 LB RF sensor lost (zone number) 381 *T End program 628 LX RF sensor restore (zone number) 381 *R Recent close
NX-10 Installers manual Special Reports Table 25.
Format key Description [X] X is optional [X …] X is optional and may be repeated one or more times. The settings and events in Table 27 are transmitted in the following messages. • >123456 BA001 BA003. • >987654 YT000. • >345678 TA030. Table 27.
NX-10 Installers manual 201 SMS Contact ID reporting Each SMS message contains only one event. The information in the message is the same as a Contact ID message sent over the PSTN with the digits coded using ASCII instead of DTMF. The following syntax is used • aaaa18qnnnggppp Table 28. Contact ID reporting syntax Format key Description aaaa Account number for the event that follows. Hexadecimal digits A - F are in upper case 18 Shows that this is a Contact ID message. q Contact ID qualifier.
Message format Messages can consist of a registered telephone number assigned to the particular user, a password, commands and values. All these elements are not case-sensitive. No national characters are allowed and should not be used - neither in commands nor in values - for example, you should type espanol instead of Español. • The telephone number part is necessary only if the system is configured to accept commands from unregistered phones, and the user calls from the telephone unknown to the system.
NX-10 Installers manual To Do This Get a list of zones with problems Send This zone faults [partition list] 203 Explanation Example Sends a list of zones with problems (like tamper, low battery, zone lost, etc.) to your phone. Sending a command without a partition list returns information for all partitions.
To Do This Send This Explanation Example To get a list of SMS commands help Sends a list of valid SMS commands to your phone. help To get a users details user details [user number] Sends the users details to your phone. user details 2 to receive a message with information about user 2 To get the current configuration of outputs list outputs Sends a list of how the outputs are currently programmed to your phone.
NX-10 Installers manual 205 01/04 05:57 Close [Arm] P1 User 1 01/04 05:57 Close [Arm] P2 User 1 Table 30. HomeText example Part of Message Description GE[Security] Site address 01/04 05:57 Date and time Close [Arm] Action reported P1 Partition number User 1 User name Glossary Term Definition A Account Code A Reporting setting that configures the SIA or Contact ID account number for the selected report receiver. SIA account numbers are 6 digits long.
Term Definition Auto-answer An Up/download setting that configures the NX-7002 to automatically answer any incoming calls. To enable this setting, you must enable Remote Initiated. Aux Short Circuit and Restores A Reporting setting that sends a report to the selected report control when too much current is detected. A restore report is also sent when the overcurrent condition is fixed. B Backup Destination A Reporting setting that configures the backup destination for the selected report control.
NX-10 Installers manual Term Definition Downloading An Options setting option that indicates that downloading is taking place. 207 E Event An alarm condition that has been detected by the control panel. Event log A list of events that occur in the system regardless of the armed state of the system. They are held in a sequential event buffer with a time and date stamp. When the log is full, it overwrites the oldest entries with new data. These events can later be viewed through downloading.
Term Definition HomeText An Options menu entry that groups together HomeText information, HomeText Control An Options setting that enables or disables HomeText. I IP Address A Reporting setting that configures the address of the selected TCP/IP receiver. An Up/download setting that configures the address of the selected TCP/IP receiver. K Keypad for Zone Text An Options setting that selects the keypad from which zone and user names are obtained.
NX-10 Installers manual 209 Term Definition Network An Options menu entry that groups network options. Non transparent mode An operating mode for CSD on a GSM network. An intermediate modem is used on the network to transfer data from one modem to another. O Only Registered Phones An Options menu setting that allows commands to be accepted only from registered HomeText phone numbers.
Term Definition compatible. PUK code Personal Unblocking Key. The code to use to unblock the SIM card. The SIM card can block when an incorrect SIM PIN is entered repeatedly. R Receiver Number A Reporting setting that configures the phone line receiver number associated with the receiver account. Receiver Polling A Reporting setting that configures the NX-7002 to send polling messages to the report receivers. Receivers A Reporting menu entry that groups TCP/IP receiver options.
NX-10 Installers manual 211 Term Definition RF Sensor Lost and Restores A Reporting setting that sends a report to the selected report control when an RF sensor is missing. A restore report is sent to the central station when the receiver receives a valid signal from the lost transmitter. RSSI Received Signal Strength Indicator. This indicates the field signal strength of the NX-7002. RSSI in test call A Reporting menu entry that adds the RSSI strength into the test report.
Term Definition Status Check An Options menu entry that groups status messages for GSM events. See chapter 5 for more information on status messages. System Control An Options menu entry that groups together HomeText system settings. T Tamper/Fault A Reporting menu entry that groups together the tamper and trouble events that are reported to the selected report control. Tampers and Restores A Reporting setting that sends a report to the selected report control when a tamper occurs.
NX-10 Installers manual 213 Term Definition Zone Bypass and Restores A Reporting setting that sends a report to the selected report control when a zone is bypassed. A report is also sent when the zone is restored (un-bypassed). Zone Inactivity Monitor A Reporting setting that sends a report to the selected report control when a zone inactivity event occurs. Zone Trouble and Restores A Reporting setting that sends a report to the selected report control when a zone trouble condition occurs.
LOC 1 2 3 4 5 6 7 8 9 DESCRIPTION DEFAULT PROGRAMMING DATA 2 Polling enable (for UL AA) 2 Reserved 3 Reserved 3 Reserved 4 TCP/IP Reporting in SIA (Contact ID if off) 4 Reserved 5 Reserved 5 Reserved 6 Reserved 6 Reserved 7 Use 3-DES encryption 7 Reserved 8 Up/downloading using GSM CSD (GSM GPRS if off) 8 Reserved 0 DESTINATION SELECTION FOR REPORT CONTROL 1 0 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 1 0 REPORT DELAY FOR REPORT CONTROL 1 EVENT SELECTION FOR REPORT CONTROL 1 (BY PARTITION) Segm
NX-10 Installers manual LOC 10 11 12 13 14 15 16 17 18 19 20 DESCRIPTION DEFAULT 0 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 3 0 REPORT DELAY FOR REPORT CONTROL 3 EVENT SELECTION FOR REPORT CONTROL 3 (BY PARTITION) Segment 1 0-0-0-0-0-0-0-0 Alarms and Restores Segment 2 0-0-0-0-0-0-0-0 Open/Close Segment 3 0-0-0-0-0-0-0-0 Bypass 0-0-0-0-0-0-0-0 Segment 4 Zone Trouble Segment 5 0-0-0-0-0-0-0-0 Power Trouble (AC Failure / Low Batt.
LOC DESCRIPTION 21 22 23 24 25 26 - 31 32 33 34 35 – 59 60 61 DEFAULT PROGRAMMING DATA 0-0-0-0-0-0-0-0 Power Trouble (AC Failure / Low Batt.
NX-10 Installers manual LOC 62 63 64 - 100 101 102 103 104-108 109 110-118 119 120 121-138 139 140 141 142 143 144 145 146 147-153 154 155 156 157 162 163 164 165 166 DESCRIPTION DEFAULT Name of GPRS access point - APN (chars 33 48) Name of GPRS access point - APN (chars 49 64) RESERVED 0.0.0.0 NX-7002 assigned IP address (DHCP) 0.0.0.0 IP address for TCP/IP receiver 1 0.0.0.0 IP address for TCP/IP receiver 2 RESERVED 0.0.0.0 IP address for download computer RESERVED 9.9.9.
LOC DESCRIPTION DEFAULT 14-14-14-14-14-14-14-1414-14-14-14-14-14-14-1414-14-14-14-14 14-14-14-14-14-14-14-1414-14-14-14-14-14-14-1414-14-14-14-14 10-10-10-10-10-10-10-10 0-0-0-0-0-0 (name of operator) 99 99 PROGRAMMING DATA 167 SMS service centre address (phone number) 168 U/D call-back phone number (for CSD GSM) 169 170 171 172 173 174 GSM SIM PIN code GSM operator selection Current GSM operator (read only) Current GSM RSSI (read only) Current GPRS Bit Error Rate % (read only) DEVICE STATUS FLAGS
NX-10 Installers manual LOC 201 202 203 204-215 216 217-224 225 226 227 228 229 DESCRIPTION DEFAULT 1 On = Disable GSM/GPRS Line Fault indication on keypad 2 On = Disable GSM/GPRS Line Fault reporting 3 On = Send RSSI combined with test call 4-8 Reserved Segment 4 - 8 Reserved Reserved Segment 1 Number of bad attempts for per 5 phone disable of HomeText control Segment 2 LCD keypad address for zone text 192 Segment 3 Reserved 3 Time for RSSI Line Fault Restore Reserved x.
LOC DESCRIPTION 230-231 232 Reserved HomeText Phone Number 1 233 HomeText Phone Number 2 234 HomeText Phone Number 3 235 HomeText Phone Number 4 236 HomeText Phone Number 5 237 HomeText Phone Number 6 238 HomeText Phone Number 7 239 HomeText Phone Number 8 240 HomeText Phone Number 9 241 HomeText Phone Number 10 242 HomeText Phone Number 11 243 HomeText Phone Number 12 244 HomeText Phone Number 13 245 HomeText Phone Number 14 246 HomeText Phone Number 15 247 HomeText Phone N
NX-10 Installers manual LOC 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280-282 283 DESCRIPTION HomeText Password for Phone Number 11 HomeText Password for Phone Number 12 HomeText Password for Phone Number 13 HomeText Password for Phone Number 14 HomeText Password for Phone Number 15 HomeText Password for Phone Number 16 Home Text Language Selection for Phone Number 1 Home Text Language Selection for Phone Number 2 Home Text Language Selection for Phone Numb
LOC 284 DESCRIPTION DEFAULT Segment 9 X-10 House Code for output 8 Segment 10 X-10 House Code for output 9 X-10 UNIT CODE FOR OUTPUTS 1 – 10 (HOMETEXT CONTROL) Segment 1 X-10 Unit Code for output 0 Segment 2 X-10 Unit Code for output 1 Segment 3 X-10 Unit Code for output 2 Segment 4 X-10 Unit Code for output 3 Segment 5 X-10 Unit Code for output 4 Segment 6 X-10 Unit Code for output 5 Segment 7 X-10 Unit Code for output 6 Segment 8 X-10 Unit Code for output 7 Segment 9 X-10 Unit Code for output 8 Segmen
NX-10 Installers manual Chapter B7 Enrolling modules Figure 25. Enrol menu 1.1 1.2 Enrol Number of Modules To enrol and default the system modules, you must enable the advanced menu. Select Maintenance Mode>Advanced Menu>Enabled and press OK. Enrolling the system modules When you select the enrol modules process, new modules are enrolled on both the control panel and the keypad. The keypad must enrol modules in order to display the relevant menu options. 1.
Glossary Location Term Definition 17 Enrol Modules A menu option that activates the process by which the control makes an internal list of all keypads and modules connected to the system. 17.1 Enrol A menu entry that groups enrolled module information. 17.2 Number of Modules A menu option that displays the total number of installed modules.
NX-10 Installers manual Chapter B8 Reading the event log Overview Figure 26. Maintenance Mode menu structure 18.1 Zone Status 18.2 Log Review 18.3 Alarm Memory 18.4 Service Check 18.5 Detector Reset 18.6 Light Control 18.7 Advanced Menu The event log displays the details of all the events that occur from when you turn the system on. A maximum of 512 events are held in the event log. To read the event log: 1. Press OK at the system prompt and enter your installer code. 2.
Table 32. Event description Event description Explanation L1 Event Type PN Partition Name L2 HH:MM DD/MM UN/ZN Zone/User Name LOG Event Type The type of event that occurred. PN The number of the partition in which the event occurred. Partition Name The name of the partition in which the event occurred. Zone/User Name The zone name or user name. UN/ZN The user number, zone number or device number. HH:MM The hour and the minute the event occurred.
NX-10 Installers manual Event message Explanation Bypass Restore See Bypass event message. Cancel The report to the central station has been cancelled. This occurs when a user enters a code after an alarm. CleanMe A smoke detector is dirty. CleanMe Restore See CleanMe event message. Clock Set A user set the date and time. Close (arm) Closing (arm) by a specific user. Code Entry The lock of the access reader has been triggered.
Event message Explanation First Open The time at which the first partition was opened. Forced Door The door was opened without an authorisation from the system. Forced Door Restore See Forced Door event message. Ground Fault Grounding problem occured. Ground Fault Restore See Ground Fault event message. Keypad Tamper A keypad tamper. Last Close The time at which the last partition was closed. Late Close A user disarmed the system after the closing time specified in the panel schedules.
NX-10 Installers manual Event message Explanation Recent Closing An alarm occurred within five minutes of the panel being armed. Re-exit A special feature of false alarm prevention. Reset A user has manually reset a smoke detector. RF Jam Restore See RF Jammed event message. RF Jammed RF jamming. RF Low Battery An RF transmitter has reported a low battery. RF Low Battery Restore See RF Low Battery event message. ROM Check Failure Failure of the ROM check.
Glossary Location Term Definition 18 Maintenance Mode A menu entry that groups options relating to issuing commands by the installer. 18.1 Zone Status A menu entry that indicates the zone status. 18.2 Log Review A menu command that is used to view the event log. The event log is a list of events that occur in the system, regardless of the armed state of the system. They are held in a sequential event buffer with a time and date stamp.
NX-10 Installers manual Chapter B9 NX-586E Overview The NX-586E direct connect module is an optional device used to interface the up/download software directly to the control panel when the on-board serial port is not available. The NX-586E direct connect module has four programming memories. The NX-586E can store up to four (4) NetworX alarm panel configurations (panel only, no modules) within its own non-volatile memory. These files can be created using the DL900 software (1.
Table 34. NX-586E direct connect module serial connector Sub D9 D25 RXD PIN 2 PIN 3 TXD PIN 3 PIN 2 GND PIN 5 PIN 7 Connect the cable to the NX-586E direct connect module. 7. Using stripped wires, connect the cable with alligator clips to a NX-10 panel as follows: • Red to POS 8. • Black to COM • Green to DATA Connecting the NX-586E to a PC and a panel Connect the NX-586E direct connect module to the serial port of the PC and the panel as shown in the previous section. Figure 28.
NX-10 Installers manual Connecting the NX-586E to a panel Connect the cable with alligator clips to a NX-10 panel as follows: • Red to POS • Black to COM • Green to DATA Programming the NX-586E direct connect module Figure 29. NX-586E menu structure 13.1 Files 13.1. File 1 Files 2 - 4 Same as above 13.2 Options 13.2.1 13.1.1. 13.1.1.2 13.1.1.
A triple beep sounds if any error occurs when reading or sending data. 8. Panel to PC memory transfer using DL900 software 1. Start the DL900 upload/download software. 2. Select: Program>Setup>Direct Connect Settings. 3. Select the correct port number and baud rate. Protocol must be Binary (default). The baud rate should match the NX-586E. Default is 9600. Click OK. 4. Select the account to use. 5. Select Download>Direct Connect. Note: You can also use the tool bar or the [F11] key. 6.
NX-10 Installers manual 6. Select the location in the NX586E from which the data will be retrieved. 7. A screen will appear indicating that the data is being read. When this screen disappears, the process is complete. 235 Location programming for the NX-586E The only location used on the NX-586E is location 0. The seven segments have the following functions and meaning: Table 35. Segment 1 Used to set the task to perform (read or write) and display the result of the task requested.
Location Term Definition 13.1.1.1 Panel Type A menu option that displays panel type information currently stored in one of the four programming memory files in the direct connect module. 13.1.1.2 Panel to File A menu option that copies a panel’s programming to one of the programming memories in the direct connect module. There are four possible programming memories in the NX-586E. 13.1.1.
NX-10 Installers manual Chapter B10 Programming with the DL900 software Other methods of programming You can program the system using the NX-1048 keypad or using the DL900 software. This software allows you to download the programming information on the control panel to the computer running the DL900 software, change it and upload the changes from the computer to the panel. It also allows you to view the program log and event log.
Connecting using a modem You can connect the control panel to the computer remotely via a modem. This can be useful if you are not on site and want to connect to the alarm system. You can connect normally or connect using answering machine defeat (AMD). If you use AMD, the automatically timed two-call-answer-machine-defeat sequence is used. To use the DL900 software with a modem connection: 1. Follow steps 1 - 5 in Connecting using a serial port above. 2. Make sure that the modem settings are correct.
NX-10 Installers manual Programming tasks You can perform all available programming tasks using the DL900 software. Table 36 DL900 menu paths shows the DL900 menu path for each task. Table 36.
Task DL900 menu option Loading the default settings Control Panel>Default Control data from>Factory defaults Logging in Start>Programs>Caddx>DL900 Printing a customer record list Program>Print preview>Customer list Printing a program log Program>Print preview>Program log Printing a programming worksheet Program>Print preview>Programming worksheet Printing an operator list Program>Print preview>Operator list Printing customer notes Program>Print preview>Notes Printing the event log Program>P
NX-10 Installers manual Task DL900 menu option Setting up answering machine defeat Program>Setup>AMD setup Specifying the direct connect settings Program>Setup>Direct connect settings Switching operators Program>Next operator Uninstalling the software Start>Settings>Control Panel Uploading Download>Read all Viewing a customer record list View>Customers>List Viewing an operator list Program>Setup>Add/Change operators Viewing the auto answer failures View>Customers>Auto answer failures View
Chapter B11 Updating firmware Overview You can upgrade the NX-10 system firmware if necessary. Upgrading to a new version may be required in order to add a new functionality to the system, add another language to the interface, include additional menu options or to fix potential problems. To upgrade the firmware you need the following: • PC with Windows OS and .NET Framework 2.
NX-10 Installers manual 6. Open the panel housing or the keypad enclosure and connect the mini-USB cable connector to the mini-USB socket on the panel (see Figure 1, position I ) or on the keypad board. 7. If the NX-9104 VVMIQ module is installed, disconnect the power supply (both mains and battery), disconnect the ribbon cable connecting the VVMIQ module with the control panel, and reconnect the power supply. 8. Click Refresh button in the Flasher interface.
Section C References
NX-10 Installers manual Appendix 1: Reporting codes in Contact ID or SIA Table 37 Event codes lists the event codes sent for different reports (if enabled) when using Contact ID or SIA formats. The numbers in brackets following the event is the number that is reported as the zone number. If there are no parentheses, the zone is 0. An asterisk represents the first character from the event code of the zone that is bypassed or in fault. Table 37.
Contact ID SIA Report Contact ID SIA Aux power restore (device number) 312 YQ Partial close 456 CF Low battery (device number) 309 YT Zone activity fault 391 NA Low battery restore (device number) 309 YR Zone activity restore 391 NS Mains fail (device number) 301 AT Fail to close 454 CI Mains restore (device number) 301 AR RF jamming 344 XQ Box tamper (device number) 137 TA RF jamming restore 344 XH Box tamper restore (device number) 137 TR Smoke detector clean me
NX-10 Installers manual 21 KH Heat Alarm Restore 22 FA Manual Fire Alarm The NX-10 can report Ademco Contact ID transmissions. Each report in Contact ID consists of an Event Code and a Zone ID. The zone ID is the zone that generated the alarm. The event code will come from the chart below, and it will be programmed in the configuration group event code. Table 39.
Appendix 2: Overview of module numbers Every keypad, expansion module and wireless receiver module has a module number. Table 40. Module numbers Module Module number NX-10 control panel 0 NX-507E/NX-508E Output expander modules 24-31 Wireless receivers 32-39 Note: NX-10 on-board receiver has address 32. IO Modules (it includes wireless sirens) 52-55 NX-534E Listen-In Module 64 NX-535 Voice Module 77 NX-7002 GPRS Module 78 Note: The NX-10 may have a GSM/GPRS interface on-board.
NX-10 Installers manual NX-1701E door swipe modules Table 41. NX-1701E module numbers Learn-in sequence Module number Learn-in sequence Module number 1 113 9 121 2 114 10 122 3 115 11 123 4 116 12 124 5 117 13 125 6 118 14 126 7 119 15 127 8 120 Keypads Table 42.
Appendix 3: Communicator formats One of several communicator formats can be used to transmit to the receiver connected to phone number 1. Consult the instructions for your central station receiver to determine which format is compatible. Table 43 Communicator formats lists the selectable communication formats. Table 43.
NX-10 Installers manual Appendix 4: Service messages The keypad displays service messages as a result of manual and automatic tests. Table 44 Service messages lists each message and outlines the action you should take to resolve the problem. When the keypad beeps due to a fault condition, press the # key to view the fault condition information. Table 44. Service messages Message Definition Action Panel Box Tamper There has been interference with the control panel casing.
Message Definition Action Remote Over-Current The expansion module has detected an excessive amount of current being drawn from one of its outputs and has disabled the output as a means of protection. Check the module for wiring faults. Remote Mains Fault The mains power supply is not connected to an expansion module power supply. Reconnect the mains power supply and ensure it is working properly. Remote Siren Fault The connection to an expansion module’s siren is broken. Repair the open circuit.
NX-10 Installers manual 253 Appendix 5: Tasks summary Users with different rights are allowed to perform different tasks in the system. Table 45 System tasks lists each task. Black fields indicate tasks that cannot be performed at the particular level, while white fields indicate allowed actions. Checkmarks denote tasks that can be performed conditionally, and conditions required are explained in the Condition column. Table 45.
Appendix 6: Word library Table 46.
NX-10 Installers manual Index A Duress code.................................................. 54 AMD...........................................235, 236, 238 E Audio reporting ..........................................186 Editing text .................................................. 38 Autotest ......................................................194 Editors.......................................................... 36 B Enrolling Backup reporting ..........................................
Internal siren.................................................53 Outputs......................................................... 13 J P K Partition Keypad settings ..................................................... 58 installing ...................................................25 number ....................................................151 timers........................................................ 58 Phone partition...................................................151 numbers.......
NX-10 Installers manual Sensors installing ...................................................33 Text editor.................................................... 38 Troubleshooting......................................... 193 Service messages........................................246 U SIA ...............................................13, 194, 242 Up/downloading ........................................ 188 SMS ........................................................189 GPRS.........................
