Full Product Manual

Installation Instructions
USE AND CARE GUIDE
WIRELESS DOOR ACTIVATED LIGHT
CONTROL
NOTE : This Class B digital apparatus complies with Canadian
ICES-003.
FCC NOTE
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. Such modifications could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
¨
Reorient or relocate the receiving antenna.
¨
Increase the separation between the equipment and receiver.
¨
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
¨
Consult the dealer or an experienced radio/TV technician for help.
WARNING: RISK OF ELECTRIC SHOCK:
¨ FULLY INSERT THE PLUG.
¨ KEEP CHILDREN AWAY.
¨ USE INDOORS ONLY.
¨ DO NOT USE IN WET LOCATIONS.
¨
UNPLUG BEFORE CLEANING.
WARNING : RISK OF FIRE
:
¨
DO NOT EXCEED ELECTRICAL RATINGS.
¨
DO NOT USE TO CONTROL MOTOR-OPERATED APPLIANCES,
TRANSFORMER-SUPPLIED APPLIANCES OR APPLIANCES THAT
CONTAIN HEATING ELEMENTS (COOKERS, IRONS, HEATERS, ETC.).
WARNING
:
Batteries may leak harmful liquids or ignitable
materials or explode causing injury or product damage.
¨
DO NOT MIX OLD AND NEW OR OTHER BATTERY TYPES.
¨
REPLACE ALL BATTERIES AT THE SAME TIME.
¨
REPLACE FULLY DISCHARGED BATTERIES IMMEDIATELY.
¨
REMOVE BATTERIES IF PRODUCT IS TO BE UNUSED FOR AN
EXTENDED PERIOD OF TIME.
RECEIVER
Functional Range Up to 100 ft.
Maximum Tungsten Load 360W
Maximum Resistive Load 1440W
zH06 / V021 / A21gnitaR
TRANSMITTER
Functional Range Up to 100 ft.
ylno esUepyT yrettaB
NOTE :
Functional range may be adversely affected by one
or more of the following factors: weather, radio frequency
interference, low transmitter battery and obstructions between
the transmitter and receiver.
noituloSmelborP
If the lighting control is not
working, check the following:
¨ Verify the device plugged into
the receiver is working.
¨ Verify the door magnet
sensors are aligned properly
with the arrows matching up.
¨ Verify the battery orientation,
noting polarity.
¨ Replace the batteries. Use only
1.5V AAA Batteries.
¨
Check to ensure that the gap
when sensor pieces 1 and 2
are mounted is no larger than
1/4 inch.
A
B
2
Installing the sensor
¨
Before installing the batteries, make sure that the switch on the sensor is
in the “off” position.
¨
Open the battery compartment on the sensor (B) and install the included
batteries, matching polarity.
¨
Use the mounting tape provided to mount the larger unit (1) on the
door frame. Next, mount the smaller unit (2) on the door parallel with
the larger unit. Ensure the arrows on the units are aligned and turn the
switch on the sensor to the “on” position.
¨
Ensure the distance between the larger unit (1) and the smaller unit (2)
is no more than 1/4 in. to ensure the product functions properly.
¨
The device will now be turned on when the door opens and turn off 30
minutes later.
3
Replacing the batteries
¨
Remove the back battery cover on the sensor (B).
¨
Remove the old batteries.
¨
Install 3 new 1.5V AAA batteries noting the polarity.
¨
Replace the battery cover.
Safety Information
Product Descrption
A. Indoor Receiver: Plug the device to be controlled into the grounded
outlet located on the indoor receiver.
B. Wireless Door Remote Transmitter: Attach the larger portion of the
magnetic sensor to the door frame. Attach the smaller portion of the
magnetic sensor to the door. Align the arrows on the sensors. When the
sensors separate the light will activate. See Installation Instructions.
A
1
2
Troubleshooting
1
Installing the receiver
¨ Plug the receiver (A) into a standard indoor grounded outlet.
¨ Plug the device to be controlled into the outlet on the receiver (A).
¨ Ensure the outlet supplying the receiver (A) is powered.
¨ Ensure the lamp or device is turned on.
1.5V AAA Batteries
MADE IN CHINA / HECHO EN CHINA
GE is a trademark of General Electric Company and is
under license by Jasco Products Company LLC, 10 E.
Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 90-day limited
warranty. Visit www.jascoproducts.com for warranty
details and product registration.
Questions? Contact us at 1-800-654-8483 between
7:30AM—5:00PM CST.
For additional assistance or information contact our Customer Service
department at 1-800-654-8483 between 7:30AM—5:00PM CST or via our
website (www.jascoproducts.com).