Owner's Manual

Wireless Door Chime
Figure 3MountingholelocationsBatterycompartmentMelodyselectionbuttonPushbutton
Installation Instructions
Required tools: Small flat blade screwdriver, #2 Phillips screwdriver and 1/16”
and 3/32” drill bit (not included)
The wireless door chime kit has two components:
Installing battery in push button
1. Remove the front cover of the push button housing by pushing a flat blade
screwdriver into the slot at the bottom of the push button housing (See Figure 1).
2. Install the CR2032 battery (included) with the positive(+) side up.
3. Keep the front cover off the push button until melody selection is complete.
Pairing the transmitter push button(s) to chime receiver
NOTE: the chime and push button(s) come paired in the package. Once batteries are
installed in the push button and chime, press the push button(s) to ensure the chime
sounds.
IF CHIME DOES NOT SOUND, FOLLOW DIRECTIONS BELOW TO PAIR THE
PUSH BUTTON(S) TO THE CHIME.
1. To clear settings: Press and hold the Pairing button on the bottom of the chime
while installing the third battery.
2. Once the last battery is installed, release the pairing button.
3. Press and hold the Pairing button again. You will hear the “Ding Dong” melody
twice, and then the double beep to alert you the chime is ready to pair with the
push button. Release the Pairing button.
4. Press and release the push button (See Figure 1). You will hear one beep
letting you know the chime accepted the signal.
5. Wait 10 seconds and you will hear the double beep again to alert you the chime
is now paired with the push button.
6. Press the push button to test.
Melody Selection Setting (your chime will have either 2 or 8 melodies)
Select the melody by pushing the melody selection button located inside the push
button housing (See Figure 1). Press and release the melody selection button until
you hear the desired melody. Table 1 and Table 2 shows the order the melodies will
be heard.
The last melody played will be your selected chime melody.
Volume Adjustment
There are three volume settings on this chime: high, medium and low.
1. To adjust the volume, press and release the pairing button on the chime or push
the push button to play the melody
2. While melody is playing, press and release the volume button on the chime to
select the desired sound level.
Push Button Mounting Instructions
NOTE: Avoid mounting on metal surfaces, as it may result in a reduced range of
transmission. Do not mount in an area exposed to direct rain. Push buttons are
typically mounted at the same height as the door knob or handle (between 36” and 44”
above the floor).
1. Remove the front cover of the push button(See Figure 1).
2. Before mounting, choose a mounting location that is no further than 150 feet
from the chime unit location. Place the push button where you would like to mount
and test with the chime as close to its final location as possible. If it works, continue
with mounting the button. If it does not work, see TROUBLESHOOTING.
3. Drill two holes with 1/16”drill bit in the marked mounting hole locations (See
Figure 3).
4. With arrow on the back plate pointing up, secure the back plate to the mounting
surface with the two 2x12mm screws included.
5. Press front housing onto back cover.
6. Test operation. If chime does not work, see TROUBLESHOOTING.
Chime Mounting Instructions
NOTE: Avoid mounting on metal surfaces, as it may result in a reduced range of
reception.
1. Select chime mounting location.
2. Using the chime mounting template on the package insert card, drill two holes
with 3/32”drill bit in marked keyhole slot locations (See Figure 2).
3. Insert the two 3x25mm screws included, into the holes, setting the screw heads
extending about ¼” from mounting surface.
4. Place the chime unit’s keyhole slots over the screws and press down on the
chime unit to secure it.
Troubleshooting
If the chime does not work:
1. Make sure push button switch is pressed down and held for at least 1 second.
2. Verify battery installation is correct, noting polarity.
3. Try a fresh battery in push button.
4. Make sure chime is no further than 150 feet away from push button.
5. Ensure push button is not mounted on metal, near metal studs, or near the floor.
6. Try a new location for the chime.
Functional range may be adversely affected by one or more of the following factors:
weather, radio frequency interference, low transmitter battery and obstructions
between the transmitter and receiver.
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encourage to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
MADE IN CHINA
GE is a trademark of General Electric Company and is under license by
Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK
73114.
This Jasco product comes with a 90-day limited warranty. Visit
www.jascoproducts.com for warranty details and product registration.
Questions? Contact us at 1-800-654-8483 between 7:30AM—5:00PM CST.
Push Button (Transmitter) Figure
1PushbuttonMountingholelocationsBatterycompartmentMelodyselectionbuttonPushbuttonPush flat blade screw driver
intothe slot to open the cover
Chime (Receiver) Figure 2pairingvolumeKeyholeslot
Table 1 - 2 Melody Chime
1 Dingdong
2 Westminster
Table 2 - 8 Melody Chime
1 Dingdong
2 Westminster
3 Knocks (3 times)
4 Fanfare
5 Mozart
6 Good Vibes
7 Patriotic
8 Tango
19248
19297
19303
Versión 02
07/31/2013