Instructions / Assembly

ManualsBrandsGE ManualsHome Decor6.5 ft. Pre-Lit Just Cut Bavarian Pine Artificial Christmas Tree with Multi-Colored Lights

3. Locate and untwist the red metal tie wrap holding

the branches in place.

Hint: if your branches do not fall into place, DO NOT

force down. Gently lift up on the branch panels to

release the branch from its locked position.{Fig. D}

Now, all rows of branches should be in the open position.

Before adding the next section, follow the shaping

instructions listed below in Step 1.

Step 1: For a natural uniform look, position some

branches outward and some upward. {Fig. E}

Repeat for each branch panel and each tree section.

The thumbscrew is to be threaded into the stand.

Insert or back-out accordingly. Look for the bottom

section of the tree, identified by a red-colored plastic

protective cap at the bottom of the

pole. Remove the cap and place the

pole into the tree stand and tighten

the thumbscrew. { Figs.B and C}

For some 7' to 12’ trees, after removing

the bubble wrap, look for the tag marked "A" attached

to the outer layer of branches. Remove the cap and

place the pole into the tree stand and tighten the

thumbscrew.

Thumbscrew

To electrically connect the sections, fully insert the

plug from the extension cord attached to the pole of

the middle section into the extension cord outlet

attached to the pole near the top of the bottom section.

NOTE: For some 5’- 6.5’ trees fully insert the plug from

the bottom layer of branches from the middle section

into the end connector from the top layer of branches

from the bottom section.

NOTE: For some 6‘-7.5’ trees, the middle section has

one long lead wire. Bring it down the tree and fully

insert the plug into the female end (add-on) of the

plug from the long lead wire from the bottom section

(2 plugs stacked together).

NOTE: For some 9’ to 12’ trees there are two wrapped

extension cords attached to sections marked A and

either B or C.

5.The bottom section of your tree also contains a wrapped

extension cord. Remove the twist tie and straighten

out the cord. At the end of the extension cord is a plug

and on some trees an On/Off FOOT PEDAL. Insert the plug

fully into a working wall outlet. Stepping on the foot

pedal will turn the power to tree On or Off.

NOTE: For trees without an extension cord, remove the

twist tie from the wrapped lead wire at the bottom of the

tree and fully insert the plug into a working wall outlet.

6.Except for some 7’ to 12’ trees, your tree, as

assembled, should now be illuminated. For some

7’ to 12’ trees, continue to add the remaining sections,

connecting the plug on the extension cord at the

bottom of the upper section into the extension cord

outlet near the top of the adjoining lower section.

Hint: If the tree does not illuminate, try stepping on

the foot pedal(s) as the power may be Off. Also, refer

to the Trouble Shooting Tips section.

8. To illuminate the top, fully insert the plug from the top

section into either the end connector or the extension cord

outlet on or near the top layer of branches of previously

assembled pole. Finish Shaping the treetop as necessary

according to the instructions in Step 1. Re-connect power

to the tree. All sections of your tree should now be

illuminated. {Fig. H}

7.Disconnect power to the tree by removing the plug(s)

from the wall outlet(s). DO NOT remove by pulling on

the cord. The remaining section to assemble is the treetop.

Hint: Shape the top prior to assembly. To shape, gently

press the branches down and away from the center

Insert the top section into the opening at the top of

the last section assembled.(Fig. G) .

A. No

Q. Can I add extra string sets to my pre-lit tree?

A. No

Q. Can I put my pre-lit tree outside?

A. No. Pre-lit trees are for indoor use only.

Q. Can, I hang glass ornaments on a pre-lit tree?

A. Yes, however, do not hang directly on the wires

of the lights.

Q. Can I remove a light string bulb and add a pig

tailed illuminated or animated ornament or motor?

A. No, removing the bulbs and inserting any additional

device into a lamp holder will cause the light set to

cease to operate and may revoke the limited

warranty of this product.

NOTE: Before opening stand make certain thumbscrew is loosened/

removed to not interfere with opening legs.

2. Remove the tree stand from the storage bag and open by pulling

apart two legs on the same side until they are 90 to each other.

NOTE: due to different metal stand designs, trees are shipped with

the thumbscrew either already threaded into the stand or packaged

separately in a bag. Make certain to check for the thumbscrew

before discarding the storage bag.

Hint: your assembled tree may be heavy and difficult

to move so place the stand in the desired location

before assembling.

9. Please check your tree for any loose, unlit or

damaged bulbs. They must be replaced promptly in

order to maintain the performance and life expectancy

of your pre-lit tree.

Your Christmas tree is complete and ready to decorate!

NOTE: This stabilizes your tree

keeping the middle section

from turning and properly

aligning the branch

panels.Untwist the

red metal tie wrap

holding the branches

in place.

Refer to Hint in 3.

Repeat the shaping

instructions in Step 1.

Find the locating key inside the bottom opening of the

tree pole from the middle section or the section marked “B”.

Find the groove key located at the top of the tree pole from

the bottom section or the section marked “A”. Align the

locating key and groove and insert the middle section

over the opening in the bottom section, sliding the key down

the groove until fully seated.

NOTE: locate the white vertical line at the top of the metal

pole of the bottom section (or the lower section just

assembled). Locate the white mark on the branch holder

frame on the middle section (or the section being assembled).

Align these two visible white marks to assemble the tree

sections together.{Fig. F} NOTE: For white trees, the color

of the distinguishing marks on the pole and branch

holder will be light green.

NOTE: on some models, the top and bottom sections

are already electrically connected.

Insert the top into the bottom being careful to keep

the cord from entering the opening and damaging

the wires.

4. If your tree contains only 2 sections, skip to 5.

Locate the middle section, identified by having a green

colored plastic protective cap. Remove the green cap from the

end of the middle section. For some 7' to 12’ trees, look for tags

marked B, then C to F attached to the outer layer of branches.

Starting with “B”, remove the end green cap and proceed.

Review Following Terms Carefully

(provided with some trees )

1. Carefully unpack, removing any bubble wrap and inspect the

contents of your tree. {Fig. A}

OutletPlug

End Connector

NOTE: No tools required

Tree Sections Tree Stand Approx. Asm Time *

3’ – 4.5’ trees 2 Metal 5 – 10 minutes

5’ – 6.5’ trees 3 Metal 10 – 15 minutes

7’-9’ trees 3 or 4 Metal 10 – 15 minutes

9’– 10.5’ trees 5 Metal 15 – 20 minutes

12’ trees 6, or 7 Metal 25 – 30 minutes

* Does not include time for shaping branches, estimated shaping time is 30 minutes/section;

Recommend use of a stepladder for trees over 6' ; Recommend two people for 12' tree

Most Frequently Asked Questions

Q. Can I add a lighted, decorative tree top to my tree?

A. Yes, There is an outlet on the back of the bladed

plug of the tree top.

Q. Can I put blinking or flashing bulbs on my tree?

Disclaimer : DO NOT USE OR INSTALL ANY ADDITIONAL

CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS

RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE

PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF

THE LIMITED WARRANTY OF THIS PRODUCT.

ATTENTION:

1.Replaceable fused lamps - identified by the

white colored ring at the top of the lamp holder.

Refer to the UL light string instructions when

replacing these lamps.

2.For White trees – to avoid the tips from discoloring:

a.Do not set up the tree in the sunlight

b.Do not set up the tree near the kitchen area

c.Avoid exposure to cigarette smoke

d.Replaceable fused lamps - identified by the

green colored ring at the top of the lamp holder.

The spare 7 amp fuse(s) for the LONG extension cord(s)

at the BOTTOM of your tree are located within the plug

cavity.

Spare Parts: Your Tree includes a plastic bag containing

spare bulbs, replaceable fused bulbs, spare 3-amp fuses,

as replacements for the lighting strings and (1) 5-amp fuse.

NOTE: This 5-amp fuse is ONLY to replace an open

fuse in the SHORT extension cord WITHIN a tree section.

Tree Storage

a) Unplug the extension cord(s) or lead wire from

the wall outlet(s).

b) Unplug and lift straight up to remove the tree top.

Step A.:Gently fold the branches up toward the

centre and place in shipping carton.

c) Unplug and lift straight up to remove the next section.

Repeat Step A.

d) Repeat Step C for 8.5'and 9' trees.

e) While holding the tree pole loosen the thumbscrew

located on the tree stand. Pull the bottom section

up and out of the tree stand. Repeat Step A.

f) To close the tree stand for storage, loosen

thumbscrew and push the brackets inward.

g) Then place the tree stand

into the shipping carton

followed by sections A,

then B and lastly C (for

8.5' & 9' trees)

h) When your tree is not

in use, be sure to store

it neatly in a cool, dry location

protected from sunlight.

FOR HINGED TREE

General Electric EZ Light

Christmas Trees

Assembly Instructions

Distributed by Nicolas Holiday Inc.,

For indoor use only

2012 Nicolas Holiday Inc.,

9 F., No. 37, Guangfu North Rd.

Taipei, Taiwan 10560

THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.

Printed in China

HG12-01W

3 Year Limited Warranty

Nicolas Holiday Inc. thanks you for your purchase of this pre-lit Christmas

tree. With proper use and care, your Christmas tree will provide

years of use and memories.

Carefully follow the instructions below on how to assemble and

disassemble your pre-lit Christmas tree.

If you should have any problems with your tree, or if the tree does not

light after assembly, DO NOT return it to the place of purchase. Please

refer to the trouble shooting section of this manual or call our toll free

number: 1-877-398-7337 and a customer service representative will

assist you.

Our customer service center is open during the off season.

Monday - Friday 8:00 - 8:00 EST

Saturday & Sunday - closed

Holiday hours (beginning the week before Thanksgiving )

Monday - Friday 8:00 -8:00 EST

Saturday & Sunday - 8:00 - 8:00 EST

You may also visit us on the web at www.geholidaylighting.com

Enjoy your holiday!

Trouble Shooting Tips

If the tree does not illuminate, try stepping on the

On/Off FOOT PEDAL and make certain the wall switch

is turned on.

If one section of your tree does not illuminate, check

that section for loose or missing bulbs, all factory

connections are properly made or that you properly

made all the electrical connections between each

tree section, i.e., tree plug to extension cord outlet.

Also, check the fused plug for a missing or burned out

(open) fuse.

16.7"X11.2"

Summary of content (2 pages)

PAGE 1
General Electric EZ Light ® Christmas Trees Assembly Instructions Hint: your assembled tree may be heavy and difficult to move so place the stand in the desired location before assembling. B C FOR HINGED TREE 3 Year Limited Warranty Nicolas Holiday Inc. thanks you for your purchase of this pre-lit Christmas tree. With proper use and care, your Christmas tree will provide years of use and memories. Carefully follow the instructions below on how to assemble and disassemble your pre-lit Christmas tree.
PAGE 2
Arboles de Navidad EZ Light ® de General Electric B C Instrucciones para el ensamblaje PARA ARBOLES CON BISAGRAS Garantía Limitada de 3 años Nicolas Holiday Inc. le agradece por la compra de este árbol de Navidad preiluminado. Con el uso y el cuidado apropiados, su árbol de Navidad le brindará años de uso y buenos recuerdos. Siga con cuidado las instrucciones siguientes para ensamblar y desarmar su árbol de Navidad preiluminado.