20309 Universal Remote Instruction Manual
Table of Contents Setup................................................................................................................................3 Battery Installation...........................................................................................3 Battery Saver.......................................................................................................3 Code Saver...........................................................................................................
Setup Battery Installation 1. 2. 3. On the back of the remote, push down on the tab and lift the cover off. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA Alkaline batteries. Press the battery cover back into place. Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).
Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. E.G. PREV. CH may be called RECALL, or ENTER may be called DISPLAY. These differences depend on the brand and model of your product. Also, this remote can only operate features that exist on your product. E.G., your product must have PREV.CH ability for the PREV.CH button to operate this feature. T V, VCR, etc. selects product to be operated. SETUP for setup.
Button Functions, cont. Turns Backlight on and off. ON•OFF Turns product On or Off. CHANNEL Up/Down Changes the channels TRACK +/- controls DVD/CD track selection i.e. DVD/ CD Track Skip Up/Down (in DVD and CD modes). INFO/DISPLAY button brings up DVD Display or Control Menu for Chapter/Track/Title number, Time remaining/elapsed indication, system information, etc. VOLUME UP/DOWN changes the volume level of the product, normally the TV.
DVD Functions This remote has several dedicated buttons used for DVD functions. The descriptions may vary from your original remote descriptions. SCAN+ and SCAN- buttons control the speed of Fast Forward and Reverse Playback respectively. SKIP (Channel Up & Down) buttons respectively locate the succeeding or preceding Chapters or Tracks on a disc. SUBTITLE (CC) Turns the subtitles on or off. TITLE Brings up the DVD Title Menu screen. REPEAT A-B button performs DVD players “A-B Repeat” (or RPT A.
SAT Functions GUIDE/PROG button displays on-screen Satellite Channel Guide. CHANNEL+ and CHANNEL- buttons perform the “Page+” and “Page-” function for on-screen Guide Menus used by some Satellite systems. INFO/DISPLAY button brings up Satellite Display screen for current Channel and system information. MENU brings up the Satellite Menu screen - use with the UP, DOWN, LEFT & RIGHT navigation buttons. OK button is used for on-screen Menu selection. EXIT button is used to Exit or Clear on-screen Menu displays.
Direct Code Entry 1. 2. 3. 4. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. Press and release the desired mode button (TV, VCR, etc.). The red indicator blinks, then stays lit. Enter the 4 digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes. With your device on, press ON•OFF. If the device turns off, no further programming is required.
Code Search If your device does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. 2. 3. 4. 5. Manually turn on the device (TV, VCR, etc.) to be controlled. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. Press and quickly release the desired mode button (TV, VCR, etc.). The red indicator blinks off once.
Using Your Remote Code Identification The Code Identification Feature allows you to identify the 4 digit library code stored under your device key. For example, if you want to find out what 4 digit code is stored under your TV device key, follow the six steps below: 1. 2. 3. 4. 5. 6. Press and hold the SETUP button until the red indicator stays on. Release the SETUP button. Press and release the desired mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
Using Your Remote, cont. Controlling Devices with Separate Power On and Off Buttons Some GE, RCA and ProScan models require you to press the device button for more than one second to turn the device on and the POWER button to turn the device off. Controlling Combo Devices Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device.
Using Your Remote, cont. Volume/Mute Control and Punch-Through This remote lets you select which device Mode controls your Volume/Mute buttons. The remote is initially set for all device Modes to use their own Volume/Mute control if present. If the programmed code has no Volume/Mute operation of its own then those buttons will punch-through control to the TV Mode device without needing to change to TV Mode.
Using Your Remote, cont. Setting any Mode to use its own Volume/Mute Control This routine can set any Mode to use only its own Volume/Mute control. Note - If your chosen Mode has no Volume/Mute functions of its own then the Volume/Mute buttons will do nothing. 1. 2. 3. 4. 5. Press and hold the SETUP button until the red indicator turns on, then release the button. Press and hold the MUTE button until the red indicator blinks off, then release the button.
Troubleshooting Remote does not operate your product. • • • • Press the mode button of the product you want to control. Program the remote with a new code. Install new batteries. (You might have to reprogram your remote after installing new batteries.) Remote may not be compatible with your product. Remote does not operate some features of your product. • • Sometimes a particular code might operate some features but not all. Try programing remote with a new code.
90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
20309 Universal Remote Instruction Manual Jasco Products Company 10 E.
