20621 Universal Remote Instruction Manual
Table of Contents Introduction...................................................................................................................3 Setup................................................................................................................................3 Battery Installation...........................................................................................3 Battery Saver..................................................................................................
Setup Battery Installation 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA Alkaline batteries. 3. Press the battery cover back into place. Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).
Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. E.g., PREV. CH may be called RECALL, or ENTER may be called DISPLAY. These differences depend on the brand and model of your product. Also, this remote can only operate features that exist on your product. E.g., your product must have PREV.CH ability for the PREV.CH button to operate this feature. TV, CBL/SAT, DVD/DVR selects product to be operated.
Button Functions, cont. ON-OFF Turns product On or Off. SETUP Used to setup the remote, and for code search function. SHIFT Press and release to access buttons labeled in reverse print (OK, MENU, EXIT). See “Using SHIFT for Menu and Navigation” description on Page 9 for more information. MUTE Turns off the TV sound while the picture remains. OK Selects menu items for the device you are controlling. VOLUME UP/DOWN changes the volume level of the product, normally the TV.
Direct Code Entry 1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 2. Press and release the desired device button (TV, DVR, etc.). The red indicator blinks, then stays lit. 3. Enter the 4-digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes. 4. With your device on, press ON/OFF. If the device turns off, no further programming is required.
Code Search If your device does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. Manually turn on the device (TV, DVR, etc.) to be controlled. 2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 3. Press and quickly release the desired device button (TV, DVR, etc.). The red indicator blinks off once. 4.
Using Your Remote Code Identification The Code Identification Feature allows you to identify the 4-digit library code stored under your device button. For example, if you want to find out what 4-digit code is stored under your TV device button, follow the six steps below: 1. Press and hold the SETUP button until the red indicator stays on. Release the SETUP button. 2. Press and release the desired device button (TV, DVR, etc.). The red indicator blinks, then stays lit. 3.
Using Your Remote, cont. Using SHIFT for Menu and Navigation The SHIFT button allows access to more than one function for certain buttons. Use the SHIFT/SETUP button prior to accessing the MENU, OK, EXIT and Navigation functions, for example: For MENU, press and release SHIFT/SETUP then MENU/INFO. For OK, press and release SHIFT/SETUP then OK/MUTE. For EXIT, press and release SHIFT/SETUP then PREV.CH/EXIT.
Using Your Remote, cont. Controlling Devices with Separate Power On and Off Buttons Some GE, RCA and ProScan models require you to press the device button for more than one second to turn the device on and the ON•OFF button to turn the device off. Controlling Combo Devices Some Combo devices (e.g., TV/DVR, TV/DVD, DVR/DVD, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device.
Using Your Remote, cont. Setting ALL Volume/Mute Control to any one Mode This routine can set all Modes to “punch-through” to any one chosen Mode for Volume/Mute button control without the needing to change to that Mode. 1. Press and hold the SETUP button until the red indicator turns on, then release the button. 2. Press and hold the MUTE button until the red indicator blinks off, then release the button. 3. Press and release the desired Mode button (TV, DVR, etc.
Troubleshooting Remote does not operate your product. • Press the device button of the product you want to control. • Program the remote with a new code. • Install new batteries. (You might have to reprogram your remote after installing new batteries.) • Remote may not be compatible with your product. Remote does not operate some features of your product. • Sometimes a particular code might operate some features but not all. Try programing remote with a new code.
90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
20621 Universal Remote Instruction Manual Jasco Products Company 10 E.
