RM24914 RM84914 Universal Remote Instruction Manual Control Remoto Universal Manual de Instrucciones DVD TV VCR MUTE INFO SLEEP INPUT ENTER Universal
Table of Contents Introduction...................................................................................... 3 Setup................................................................................................... 3 Battery Installation................................................................ 3 Battery Saver............................................................................ 3 Code Saver................................................................................ 3 Code Setup....
Setup Battery Installation 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA Alkaline batteries. 3. Press the battery cover back into place. Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).
Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. E.G. PREV.CH may be called RECALL, or ENTER may be called DISPLAY. These differences depend on the brand and model of your product. Also, this remote can only operate features that exist on your product. E.G., your product must have PREV.CH ability for the PREV.CH button to operate this feature. TV, CBL/SAT, DVD, VCR Selects product to be operated.
Button Functions, cont. SETUP Used to setup the remote, and for code search function. SHIFT Press and release to access buttons labeled in reverse print (OK, MENU, EXIT). See “Using SHIFT for Menu and Navigation” description on Page 9 ON•OFF Turns product On or Off. MUTE Turns off the TV sound while the picture remains. OK Selects menu items for the device you are controlling. VOLUME UP/DOWN Changes the volume level of the product, normally the TV. CHANNEL Up/Down Changes the channels.
Direct Code Entry 1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 2. Press and release the desired device button (TV, VCR, etc.). The red indicator blinks, then stays lit. 3. Enter the 4 digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes. 4. With your device on, press ON•OFF. If the device turns off, no further programming is required.
Code Search If your device does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. Manually turn on the device (TV, VCR, etc.) to be controlled. 2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 3. Press and quickly release the desired device button (TV, VCR, etc.). The red indicator blinks off once. 4.
Using Your Remote Code Identification The Code Identification Feature allows you to identify the four digit library code stored under your device button. For example, if you want to find out what four digit code is stored under your TV device button, follow the six steps below: 1. Press and hold the SETUP button until the red indicator stays on. Release the SETUP button. 2. Press and release the desired device button (TV, VCR, etc.). The red indicator blinks, then stays lit. 3.
Using Your Remote, cont. Using SHIFT for Menu and Navigation The SHIFT button allows access to more than one function for certain buttons. Use the SHIFT/SETUP button prior to accessing the MENU, OK, EXIT and Navigation functions e.g.: For MENU, press and release SHIFT/SETUP then MENU/INFO. For OK, press and release SHIFT/ SETUP then OK/MUTE. For EXIT, press and release SHIFT/ SETUP then EXIT/SLEEP.
Using Your Remote, cont. Sleep Function The Sleep button enables the remote to turn off your TV after a period of 1 to 99 minutes as shown below. The remote must be in TV mode to set a Sleep Timer. This feature works even if your TV does not have a sleep feature. 1. Press and release the TV device button. 2. Press and hold the Sleep button until the LED remains lit (about 2-3 seconds). 3. Release the Sleep button. 4. Press and release the numeric buttons (01-99) for the time required.
Using Your Remote, cont. Controlling Devices with Separate Power On and Off Buttons Some GE, RCA and ProScan models require you to press the device button for more than one second to turn the device on and the ON•OFF button to turn the device off. Controlling Combo Devices Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device.
Using Your Remote, cont. Volume/Mute Control and Punch-Through This remote lets you select which device Mode controls your Volume/Mute buttons. The remote is initially set for all device Modes to use their own Volume/Mute control if present. If the programmed code has no Volume/Mute operation of its own then those buttons will punch-through control to the TV Mode device without needing to change to TV Mode.
Using Your Remote, cont. Setting any Mode to use its own Volume/ Mute Control This routine can set any Mode to use only its own Volume/Mute control. Note - If your chosen Mode has no Volume/Mute functions of its own then the Volume/Mute buttons will do nothing. 1. Press and hold the SETUP button until the red indicator turns on, then release the button. 2. Press and hold the MUTE button until the red indicator blinks off, then release the button. 3. Press and release the desired Mode button (TV, VCR, etc.
Troubleshooting Remote does not operate your product. • Press the device button of the product you want to control. • Program the remote with a new code. • Install new batteries. (You might have to reprogram your remote after installing new batteries.) • Remote may not be compatible with your product. Remote does not operate some features of your product. • Sometimes a particular code might operate some features but not all. Try programing remote with a new code.
90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
Tabla de Contenido Introducción .................................................................................17 Configuración ..............................................................................17 Instalación de las baterías .............................................17 Ahorrador de baterías ......................................................17 Protección de códigos ......................................................17 Configuración de códigos ..........................................
Configuración Instalación de las baterías 1. Presione hacia abajo la lengüeta en la parte posterior del control remoto y retire la tapa. 2. Inserte dos baterías alcalinas tamaño AAA de manera que correspondan con las marcas + y – del compartimiento. 3. Ajuste nuevamente la tapa haciendo presión. Ahorrador de baterías El control remoto se apagará automáticamente si algún botón se mantiene oprimido por más de 30 segundos.
Funciones de los botones Algunos botones del control remoto podrían tener funciones que corresponden a nombres diferentes en el aparato que está controlando. Por ejemplo, puede que PREV.CH se llame RECALL, o ENTER se llame DISPLAY. Tales diferencias dependen de la marca y el modelo de su producto. Igualmente, este control remoto sólo puede ejecutar funciones que existan en su producto. Por ejemplo, su producto debe tener la función PREV. CH para que el botón PREV.CH pueda ejecutarla.
Funciones de los botones, continuación SETUP Se usa para configurar el control remoto y para la función de búsqueda de códigos. SHIFT Presione y suelte para acceder a los botones con nombres en impresión invertida (OK, MENU, EXIT). Ver más información en “Uso de SHIFT para menú y navegación” en la página 9. ON-OFF Enciende y apaga el producto. MUTE Silencia el sonido del televisor dejando sólo la imagen. OK Selecciona las opciones de menú para el aparato que está controlando.
Entrada directa de códigos 1. Mantenga presionado el botón SETUP hasta que el indicador rojo permanezca encendido y luego suelte el botón SETUP. 2. Presione y suelte el botón del aparato deseado (TV, VCR, etc.). El indicador rojo parpadeará y después permanecerá encendido. 3. Ingrese un código de quattrodígitos de las tablas de códigos (que se encuentran en una hoja aparte). Nota: Después de ingresar un código válido, el indicador rojo se apagará.
Búsqueda de códigos Si el aparato no responde después de haber intentado todos los códigos para la marca o si la marca no aparece en la lista, busque el código siguiendo estos pasos: 1. Encienda manualmente el aparato (TV, VCR, etc.) que va a controlar. 2. Mantenga presionado el botón SETUP hasta que el indicador rojo permanezca encendido y luego suelte el botón SETUP. 3. Presione y suelte rápidamente el botón del aparato deseado (TV, VCR, etc.). El indicador rojo parpadeará una vez y permanecerá apagado.
Cómo utilizar el control remoto Identificación de códigos La función de identificación de códigos permite identificar el código de biblioteca de quattro dígitos almacenado en el botón de cada aparato. Por ejemplo, si usted quiere saber qué código de quattro dígitos está almacenado en el botón de TV, siga estos seis pasos: 1. Mantenga presionado el botón SETUP hasta que el indicador rojo permanezca encendido. Suelte el botón SETUP. 2. Presione y suelte el botón del aparato deseado (TV, VCR, etc.).
Cómo utilizar el control remoto, continuación Uso de SHIFT para menú y navegación El botón SHIFT permite el acceso a más de una función de ciertos botones. Use el botón SHIFT/SETUP antes de acceder a las funciones MENU, OK, EXIT y a las de navegación. Por ejemplo: Para MENÚ, presione y suelte SHIFT/ SETUP y luego MENU/INFO. Para OK, presione y suelte SHIFT/ SETUP y luego OK/MUTE. Para EXIT, presione y suelte SHIFT/ SETUP y luego EXIT/SLEEP.
Cómo utilizar el control remoto, continuación Función Sleep La función Sleep permite que el control remoto apague su televisor después de un periodo entre 1 y 99 minutos como se muestra enseguida. Para configurar el temporizador de Sleep el control remoto debe estar en modo TV. La función Sleep se ejecuta aun cuando su televisor no cuente con esta característica. 1. Presione y suelte el botón de TV. 2.
Cómo utilizar el control remoto, continuación Control de aparatos con botones de encendido/apagado independientes En algunos modelos GE, RCA y ProScan es necesario presionar el botón de aparato durante más de un segundo para encender el aparato y el botón ON-OFF para apagarlo. Control de aparatos combinados Para algunos aparatos combinados (por ejemplo, TV/ VCR, TV/DVD, DVD/VCR, etc.) se necesitará configurar dos botones de modo diferentes para controlar ambas partes del aparato combinado.
Cómo utilizar el control remoto, continuación Control y cambio de control de Volumen/Mute Este control remoto le permite seleccionar el modo del aparato controlará los botones Volume/Mute. El control remoto está configurado inicialmente para que todos los aparatos utilicen su propio control de Volumen/Mute, si lo tienen. Si el código programado no tiene operación Volumen/Mute propia, entonces esos botones cambiarán el control al modo TV sin necesidad de cambiar a modo TV.
Cómo utilizar el control remoto, continuación Configuración para que cualquier modo use su propio control de Volume/Mute El control remoto puede configurarse para que cualquier modo use solamente su propio control de Volumen/Mute. Nota: si el modo escogido no tiene su propia función de Volumen/Mute, los botones de Volume/Mute no harán nada. 1. Mantenga presionado el botón SETUP hasta que el indicador rojo se encienda, luego suelte el botón. 2.
Solución de problemas El control remoto no opera el producto. • • • • Presione el botón de aparato del producto que quiere controlar. Programe el control remoto con un nuevo código. Instale baterías nuevas. (Puede que necesite volver a programar el control remoto después de instalar las baterías nuevas). Puede que el control remoto no sea compatible con su producto. El control remoto no ejecuta algunas funciones en el producto.
Garantía limitada de 90 días Jasco Products Company garantiza que este producto está libre de defectos de fabricación durante un periodo de noventa días a partir de la fecha original de compra por parte del consumidor. Esta garantía se limita a la reparación o reemplazo de este producto solamente y no se extiende a daños derivados o accidentales causados a otros productos que se usen con esta unidad. Esa garantía sustituye a todas las demás garantías explícitas o implícitas.
RM24914 RM84914 Universal Remote Instruction Manual Control Remoto Universal Manual de Instrucciones Jasco Products Company 311 N.W.