24958 Universal Remote Instruction Manual
Table of Contents Introduction................................................3 Button Functions.......................................4 Initial Setup................................................6 Battery Installation.................................6 Battery Saver........................................6 Code Saver...........................................6 Code Setup...........................................6 Direct Code Entry......................................7 Code Search........................
Introduction Congratulations on your purchase of this 24958 Universal Remote Control. The 24958 is one of the most easy to use remote controls available today. With the 24958, juggling multiple remote controls is a thing of the past! Your 24958 controls up to 6 devices, including the most popular brands of TV, DVD, DVR, Cable, etc.
Button Functions 1. 27. 2. 26. 3. 25. 4. 24. 5. 23. 6. 22. 7. 21. 8. 20. 9. 19. 10. 18. 11. 17. 12. 16. 13. 15. 14. Note: The REC button must be pressed twice to record from your DVD/DVR. For some DVD/DVR brands, you might need to press REC button once, then press it again for 3 seconds. Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. These differences depend upon the brand and model of your product.
Button Functions (cont.) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. Red Indicator: Lights when any button is pressed. TV, DVD, DVR, etc.: Selects the product to be operated. SETUP: Used for setting up your remote. ABCD: Used to store learned commands. MENU: Brings up the device Menu screen (if available) - use with UP, DOWN, LEFT, and RIGHT navigation buttons. UP, DOWN, LEFT, RIGHT: Navigation buttons.
Initial Setup Battery Installation 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA Alkaline batteries. 3. Press the battery cover back into place. Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g.
Direct Code Entry Direct Code Entry NOTE: You can store any kind of code under any mode (except TV). I.E. you can store a VCR code under the CBL button, or a DVD code under the AUX button, etc. However, you can only store TV codes under the TV button. 1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 2. Press and release the desired mode button (TV, DVD, etc.). The red indicator blinks, then stays lit. 3.
Code Search Code Search If your product does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. Manually turn on the device (TV, DVD, etc.) to be controlled. 2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 3. Press and quickly release the desired mode button (TV, DVD, etc.). The red indicator blinks off once. 4.
Code Identification Feature Code Identification Feature The Code Identification Feature allows you to identify the 4 digit library code stored under your device key. For example, if you want to find out what 4 digit code is stored under your TV device key, follow the six steps below: 1. Press and hold the SETUP button until the red indicator stays on. Release the SETUP button. 2. Press and release the desired mode button (TV, DVD, etc.). The red indicator blinks, then stays lit. 3.
Setup Programming Combo Device Codes Some combo (combination) devices (TV/DVR, TV/ DVD, DVD/DVR, etc.) require you to set up 2 different modes to control both parts of the combo. For example, if you have a TV/DVD combo, you might need to set up one code under the TV mode to control the TV and a separate code (under other modes) to control the DVD. DVD/DVR Punch-Through Feature This remote allows the 6 DVD/VCR transport buttons (i.e.
Setup (cont.) Setting ALL Volume/Mute Controls to Any Mode You can set all modes to “punch-through” to any mode for Volume/Mute control without needing to change to that mode by doing the following. 1. Press and hold SETUP until the indicator remains on, then release SETUP. 2. Press and hold MUTE until the indicator blinks off, then release the button. 3. Press and release SELECT to select the desired mode (TV, DVD, etc.) for Volume/Mute control; the indicator blinks, then stays on. 4.
Code Learning commands. g. Place the original remote end-to-end with the Learning Remote so the IR transmitters on both remotes are directly in line with each other. You may need to adjust the height of either remote to achieve this. Use the IR Transmitter Finder feature to assist you. h. Keep the distance between the two remotes to approximately 1 inch and do not move or change the distance between the two remotes until you have learned all the required buttons for that Mode. i.
Tips On Learning (cont.) The learning feature lets you “learn” functions from your original remote control. For example - you may want to use your remote to operate the RANDOM PLAY feature from your original CD remote control. This remote is equipped with an “easy learning” feature that lets you “learn” features (such as RANDOM PLAY from your original CD remote). Tips on Learning You can only learn one device type under any one Mode button e.g.
IR Transmitter Finder This feature assists you in identifying where your original remotes IR transmitter is located and is particularly useful if your original remote’s IR transmitter is hidden behind a lens. 1. Point both remotes facing each other by approximately 1 inch apart (see Tips on Learning on previous pages). 2. Press and hold the SETUP button until the red indicator turns on, then release the button. 3. Press and release the desired Mode button (TV, DVD, etc.
Learning Commands 1. Press and hold the SETUP button until the red indicator turns on, then release the button. 2. Press and release the desired mode button (TV, DVD, etc.), the red indicator blinks then stays on. 3. Press and release the LEARN button, the red indicator blinks then stays on. 4. Press and release the Learning Remote button that you want to teach (e.g. POWER). 5. Point both remotes facing each other by approximately 1 inch apart (see tips on page 12). 6.
Clearing Commands To Clear all Learned Commands under a mode 1. Press and hold the SETUP button until the red indicator turns on. Release the SETUP button. 2. Press and release the button for the mode you want to clear (TV, DVD, etc.). The red indicator blinks off. 3. Press and release the LEARN button TWICE. The red indicator blinks off. 4. Press and release the SETUP button. The red indicator turns off. All learned Commands under that mode are now cleared.
Troubleshooting Remote does not operate your product 1. Select the mode for the product you want to control. 2. Program the remote with a new code. 3. Install new batteries in the remote. (You might have to reprogram your remote after installing new batteries.) 4. If these steps do not work, the remote might not be compatible with your product. Remote does not operate some features of your product 1. Program remote with a new code. 2.
90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
24958 Universal Remote Instruction Manual Jasco Products Company 10 E.
