RM24970 Universal Remote Instruction Manual
Table of Contents Introduction............................................................. 3 Setup...................................................................... 3 Battery Installation............................................. 3 Battery Saver..................................................... 3 Code Saver....................................................... 3 Code Setup....................................................... 3 Button Functions...............................................
Setup Battery Installation 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA Alkaline batteries. 3. Press the battery cover back into place. Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).
Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. E.G. PREV.CH may be called RECALL, or ENTER may be called DISPLAY. These differences depend on the brand and model of your product. Also, this remote can only operate features that exist on your product. E.G., your product must have PREV.CH ability for the PREV.CH button to operate this feature. GUIDE displays satellite or cable on-screen program guide. TV, VCR, etc.
Button Functions, cont. ON•OFF Turns product On or Off. Navigation buttons and SELECT used to move through on-screen menuing and guides. With some DBS models the DISP button should be used to select the highlighted item. Use the navigation buttons to move the highlighted choice up, down, left, or right. DISP Display button shows date and time if your TV or VCR has that feature. CLEAR Removes the on screen display to return to normal viewing. PREV.CH Returns to the previously selected channel.
Audio Button Descriptions Press the AUDIO device button to enable the AUDIO MODE. Audio functions are indicated by the blue button descriptions. LEVEL+/LEVEL- Sets the level of the speakers during test tone mode. DSP ON•OFF Enables the receiver’s Digital Sound Processing mode. DSP MODE When the DSP mode is enabled, pressing this button lets you toggle through the various DSP modes. CD, TAPE, TUNER, TV, VIDEO Used to directly select the device you want to control. (Works in AUDIO mode).
Audio Functions, cont. Using the number buttons to change audio inputs To select a device, press the number button (1-6) that corresponds to the device you want to operate (CD, TAPE, TUNER, TV, or VIDEO). Using the function buttons to change audio devices To select a device, press the FUNCTION button until the input you want to operate appears on your system. Operating a CD player or Tape Deck Use the Play, Forward, Reverse, Record, Stop, and Pause buttons for CD Players and Tape Decks.
Surround Sound Feature The surround sound feature may be turned ON/ OFF by pressing the SURR ON•OFF button. 1. Press the SURR MODE button until the desired mode is found. 2. Press DELAY+ or DELAY- to achieve the desired delay affect. 3. Press the DSP ON•OFF button to turn DSP (Digital Sound Processor) ON or OFF. 4. Press the DSP mode button until the desired effect is achieved. 5. Press the TEST button to listen to speaker levels. 6. Press FRONT, CENTER, or REAR buttons to select speakers. 7.
Direct Code Entry 1. Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button. 2. Press and release the desired device button (TV, VCR, etc.). The red indicator blinks, then stays lit. 3. Enter the 4 digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes. 4. With your device on, press ON•OFF. If the device turns off, no further programming is required.
Code Search If your device does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. Manually turn on the device (TV, VCR, etc.) to be controlled. 2. Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button. 3. Press and quickly release the desired device button (TV, VCR, etc.). The red indicator blinks off once. 4.
Using Your Remote Code Identification The Code Identification Feature allows you to identify the four digit library code stored under your device button. For example, if you want to find out what four digit code is stored under your TV device button, follow the six steps below: 1. Press and hold the CODE SEARCH button until the red indicator stays on. Release the CODE SEARCH button. 2. Press and release the desired device button (TV, VCR, etc.). The red indicator blinks, then stays lit. 3.
Using Your Remote, cont. Sleep Function The Sleep button enables the remote to turn off your TV after a period of 1 to 99 minutes as shown below. The remote must be in TV mode to set a Sleep Timer. This feature works even if your TV does not have a sleep feature. 1. Press and release the TV device button. 2. Press and hold the Sleep button until the LED remains lit (about 2-3 sec- onds). 3. Release the Sleep button. 4. Press and release the numeric buttons (01-99) for the time required.
Using Your Remote, cont. Controlling Devices with Separate Power On and Off Buttons Some GE, RCA and ProScan models require you to press the device button for more than one second to turn the device on and the ON•OFF button to turn the device off. Controlling Combo Devices Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device.
Using Your Remote, cont. Volume/Mute Control and PunchThrough This remote lets you select which device Mode controls your Volume/Mute buttons. The remote is initially set for all device Modes to use their own Volume/Mute control if present. If the programmed code has no Volume/Mute operation of its own then those buttons will punch-through control to the TV Mode device without needing to change to TV Mode.
Using Your Remote, cont. Volume/Mute Control This routine can set any Mode to use only its own Volume/Mute control. Note - If your chosen Mode has no Volume/Mute functions of its own then the Volume/Mute buttons will do nothing. 1. Press and hold the CODE SEARCH button button. until the red indicator turns on, then release the 2. Press and hold the MUTE button until the red indicator blinks off, then release the button. 3. Press and release the desired Mode button (TV, VCR, etc.
Troubleshooting Remote does not operate your product. • • • • Press the device button of the product you want to control. Program the remote with a new code. Install new batteries. (You might have to reprogram your remote after installing new batteries.) Remote may not be compatible with your product. Remote does not operate some features of your product. • • Sometimes a particular code might operate some features but not all. Try programing remote with a new code.
90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
RM24970 Universal Remote Instruction Manual Jasco Products Company 311 N.W.