Instructions / Assembly

ManualsBrandsGE ManualsHome Decor10.5 ft. Pre-Lit LED Just Cut Deluxe Aspen Fir Artificial Christmas Tree with Color Choice Lights

FOR HINGED TREE

NOTE: Before opening stand make certain thumbscrew

is loosened/removed to not interfere with opening legs.

2. Remove the tree stand from the storage bag and

open by pulling apart two legs on the same side until

they are 90 to each other.

NOTE: due to different metal stand designs, trees are

shipped with the thumbscrew either already threaded

into the stand or packaged separately in a bag. Make

certain to check for the thumbscrew before discarding

the storage bag.

Disclaimer : DO NOT USE OR INSTALL ANY ADDITIONAL

CHRISTMAS LIGHTING OR ORNAMENTATION THAT IS

RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE

PERSONAL INJURY. DOING THIS, WILL RESULT IN A VOID OF

THE LIMITED WARRANTY OF THIS PRODUCT.

Review Following Terms Carefully

1. Carefully unpack, removing any bubble wrap and inspect the

contents of your tree. {Fig. A}

Plug

Male Connector

with Securing Cap

NOTE: No tools required

Tree Sections Tree Stand Approx. Asm Time *

3 ft – 4.5 ft trees 2 Metal 5 – 10 minutes

5 ft – 6.5 ft trees 3 Metal 10 – 15 minutes

7 ft -9 ft trees 3 or 4 Metal 10 – 15 minutes

9 ft – 10.5 ft trees 5 Metal 15 – 20 minutes

12 ft trees 6 or 7 Metal 25 – 30 minutes

* Does not include time for shaping branches, estimated shaping time is

30 minutes/section;

Recommend use of a stepladder for trees over 6 ft ; Recommend two people

for 12 ft tree

General Electric EZ Light

Christmas Trees

Assembly Instructions

Spare Parts: Your Tree includes a plastic bag containing

spare LEDs.

Distributed by Nicolas Holiday Inc.,

For indoor use only

2015 Nicolas Holiday Inc.,

9 F., No. 37, Guangfu North Rd.

Taipei, Taiwan 10560

THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.

Printed in China

HG15-DUAL

Nicolas Holiday Inc. thanks you for your purchase of this pre-lit Christmas

tree. With proper use and care, your Christmas tree will provide

years of use and memories.

Carefully follow the instructions below on how to assemble and

disassemble your pre-lit Christmas tree.

If you should have any problems with your tree, or if the tree does not

light after assembly, DO NOT return it to the place of purchase. Please

refer to the troubleshooting section of this manual or call our toll free

number: 1-877-398-7337 and a customer support representative will

assist you.

Our customer support center is open Monday through Friday 10AM

to 7PM EST with additional hours throughout the holiday season:

November 14th to December 23rd:

Monday-Friday 8AM to 8PM EST,

Saturday-Sunday: 10AM to 7PM EST

You may also visit us on the web at www.geholidaylighting.com

Enjoy your holiday!

16.7"X11.2"

3. Locate and untwist the red metal tie wrap holding

the branches in place.

Hint: if your branches

do not fall into place,

DO NOT force down.

Gently lift up on the

branch panels to

release the branch

from its locked

position.{Fig. C}

Now, all rows of branches should be in the open position.

Before adding the next section,

follow the shaping

instructions listed

below in Step 1.

Step 1: For a natural

uniform look, position

some branches

outward and some

upward. {Fig. D}

Repeat for each branch panel and each tree section.

The thumbscrew is to be threaded into the stand.

Insert or back-out accordingly. Look for the bottom

section of the tree, identified by a red-colored plastic

protective cap at the bottom of the pole. Remove the

cap and place the pole into the tree stand and tighten

the thumbscrew. { Figs.B }

For some 7 ft to 12 ft trees, after removing the bubble

wrap, look for the tag marked "A" attached to the outer

layer of branches. Remove the cap and place the

pole into the tree stand and tighten the thumbscrew.

Thumbscrew

7.Remove the twist tie from the wrapped lead wire at

the bottom of the tree and fully insert the plug into a

working wall outlet. All sections of your tree should now

be illuminated. {Fig. G}

WARNING:

All tree sections must be electrically connected together

before inserting this plug into an outlet. Failure to heed

this warning damages the electronics with the lights

not working.

6.To electrically connect the top, again refer to the Tree

Assembly Diagram taking the male and female

connectors, aligning the flat areas and fully inserting

together.

Fully screw on securing cap. Finish shaping the treetop

as necessary according to the instructions in Step 1.

5.The remaining section to assemble is the treetop.

Hint: Shape the top prior to assembly. To shape, gently

press the branches down and away from the center.

Insert the top section into the opening at the top of

the last section assembled. (Fig. F)

NOTE: on some models, the top and bottom sections are

already electrically connected.

Insert the top into the bottom being careful to keep

the cord from entering the opening and damaging

the wires.

Your Christmas tree is complete and ready to decorate!

Untwist the red metal tie wrap

holding the branches

in place.Refer to Hint in 3.

Repeat the shaping

instructions in Step 1.

NOTE: For some 7 ft to 12 ft trees, look for the tags marked

B, then C to F attached to the outer layer of the branches.

Starting with “B”, remove the green protective cap and

proceed to find the arrow on the brown plastic collar on

the end of the bottom section or the section marked “A”.

These markings provide the proper branch panel

alignment between the two tree sections. { Fig. E }

Place the middle section or the section marked “B” into

the bottom section or the section

marked “A” while aligning

these two marks. Slide the middle

section or the section

marked “B” completely into the

bottom section or the section

marked “A” to stabilize the tree.

4. If your tree contains only 2 sections, skip to 5.

Locate the middle section or the section marked “B”,

identified by having a green-colored plastic protective

cap at the bottom of the pole. Remove the green cap and

locate the grooved peg at the bottom of the middle section

or the section marked “B”.

Most Frequently Asked Questions

Q. May I add a lighted, decorative tree topper to my tree?

A. Yes, But you would have to use separate extension

cord to power the tree topper.

Q. May I put blinking or flashing bulbs on my tree?

A. No

Q. May I add extra string sets to my pre-lit tree?

A. No

Q. May I put my pre-lit tree outside?

A. No. Pre-lit trees are for indoor use only.

Q. May I hang glass ornaments on a pre-lit tree?

A. Yes, however, do not hang directly on the wires

of the lights.

Q. May I remove a light string bulb and add a pig

tailed illuminated or animated ornament or motor?

A. No, removing the bulbs and inserting any additional

device into a lamp holder will cause the light set to

cease to operate and may revoke the limited

warranty of this product.

Troubleshooting Tips

If one section of your tree does not illuminate, check

that section for loose or missing bulbs, all factory

connections are properly made or that you properly

made all the electrical connections between each

tree section.

Tree Storage

1. Remove the tree’s main extension cord plug from

the wall outlet. Do not unplug by pulling on the cord.

2. Starting at the top, untwist the securing cap and

disconnect the male and female connectors between

the top and section B.

3. Carefully lift the treetop straight up* from the lower

section. If tightly seated, then wiggle treetop slightly

to loosen.

* Use of a ladder is suggested to avoid bending of

the treetop. Please exercise care when using a

ladder to maintain balance.

Step A: Gently fold the branches up toward the center.

Care should be taken to avoid damage to the lights.

4. Place the treetop into your original shipping carton

with the top in a corner at one end.

5. Untwist the securing cap and disconnect the male

and female connectors between sections B and A.

6. Remove section B, collapse the hinges, repeat

Step A and set-aside.

7. While holding the tree pole of section A, loosen

the thumbscrew located on the tree stand.

8. Remove section A from the tree stand, collapse

the hinges and repeat Step A.

9. Place section A into the carton with the top of the

section at the opposite end of the treetop, as pole

A lays along side the treetop.

10. To close the tree stand for storage, loosen thumbscrew

sufficiently to then push the legs inward.

11. Place the tree stand vertically along the long side

of the carton or lay it flat on the bottom.

12. Carefully place section B into the carton over the

Treetop with its pole lying along side section A.

13. Seal the carton closed.

Important: Store your carton neatly in a cool, dry location

protected from sunlight to prolong the tree life and to

better keep the light sets in working order. Do not place a

heavy load on the carton to avoid damage to or crushing

the carton and tree inside.

TREE ASSEMBLY DIAGRAM

TOP

To electrically connect the sections please refer to the

Tree Assembly Diagram. Take the male and female

connectors, locate the flat area on each and fully insert

the connectors together. Fully screw on securing cap.

9. Please check your tree for any loose, unlit or

damaged bulbs. They must be replaced promptly in

order to maintain the performance and life expectancy

of your pre-lit tree.

8. To change colors step on the color change

foot pedal to the desired function as listed on

the back of the foot pedal.

Female Connector

Function List:

1. Steady White

2. Steady Multi

3.White & Multi Color Change

4. Off

Color Change

Foot Pedal

Function List:

1. Steady White

2. Steady Multi

3.White & Multi

Color Change

4. Off

Summary of content (2 pages)

PAGE 1
General Electric EZ Light ® Christmas Trees Assembly Instructions NOTE: No tools required Tree Sections 3 ft – 4.5 ft 5 ft – 6.5 ft 7 ft -9 ft 9 ft – 10.5 ft 12 ft FOR HINGED TREE Nicolas Holiday Inc. thanks you for your purchase of this pre-lit Christmas tree. With proper use and care, your Christmas tree will provide years of use and memories. Carefully follow the instructions below on how to assemble and disassemble your pre-lit Christmas tree.
PAGE 2
Arboles de Navidad EZ Light ® de General Electric NOTA: No se necesitan herramientas. Secciones Instrucciones para el ensamblaje PARA ARBOLES CON BISAGRAS Nicolas Holiday Inc. le agradece por la compra de este árbol de Navidad preiluminado. Con el uso y el cuidado apropiados, su árbol de Navidad le brindará años de uso y buenos recuerdos. Siga con cuidado las instrucciones siguientes para ensamblar y desarmar su árbol de Navidad preiluminado.