33700 | 33701 Universal Remote Instruction Manual tv cbl tv setup sleep input setup vers2 | 3/17 cbl sleep input 6177
Table of Contents Introduction...................................................................................... 2 Setup................................................................................................... 3 Button Functions........................................................................... 4 Programming Your Remote...................................................... 6 Direct Code Entry................................................................... 6 Auto Code Search.........
Setup Your universal remote requires two (2) AA batteries (not included). Alkaline batteries are recommended. Battery Installation 1. On the back of the remote, pull down on the textured surface and slide battery cover downward to remove. 2. Match the (+) and (-) marks on the batteries to the (+) and (-) marks inside the battery compartment, then insert two (2) AA batteries. Be sure to use fresh batteries. 3. Position battery cover slightly below opening and push upward to lock into place.
Button Functions 1 2 cbl tv 3 4 5 6 8 9 10 11 7 setup sleep input 12 4
Button Functions 1. Power - Turns devices ON/OFF 2. TV, cbl - Selects the device to control 3. Volume Up/Down 4. Channel Up/Down 5. Mute - Mutes sound 6. Previous Channel - Returns to the previously selected channel 7. Numbers - Used for direct channel selection 8. Dot (•) - Used to select digital channels, e.g., 4.1 9. Enter - Some devices require Enter to be pressed after channel selection 10. Setup - Used to program the remote 11. Input - Selects video inputs 12.
Programming Your Remote Your remote is designed to control multiple audio/video devices. To use, you will need to program the remote for your devices. There are two different methods you can use to program the remote, Direct Code Entry or Auto Code Search. • The Direct Code Entry method is the recommended method as it is the simplest and quickest method in most cases. • The Auto Code Search method searches through all the codes in the remote to find a code for your device.
Programming Your Remote 4. Use the number buttons on the remote to enter the first 4-digit remote code you circled in the Code List in Step 1. The red light will turn off after entering the fourth digit. 5. Point the remote at the device. Test the buttons on the remote to see if the device responds as you would expect. If the buttons do not operate the device, return to Step 2 above and use the next code that you circled for that device. 6. Repeat Steps 1 – 5 for each device you wish to control.
Programming Your Remote Auto Code Search The Auto Code Search is a process where you can search through all the codes stored in the remote to find a code for your device. It is recommended that you read through all the steps below to familiarize yourself with the Auto Code Search before starting the process. 1. Manually turn on the device you wish to control. Note: The Auto Code Search process cannot be used for devices without power ON/OFF capability. Use the Direct Code Entry method in these cases. 2.
Programming Your Remote 1 tv 3 Did the device turn off? • If YES, you have found a code for the device. Press and release the same device button you pressed in Step 3. This will store the code in the remote. Go to Step 7. •cbl If NO, continue to press and release the VOL + button until the device turns off to test the other 9 codes from Step 4. Be sure to wait approximately 3 seconds after each VOL + button press to allow the device time to respond to the code.
Using Your Remote Master Volume Feature The Master Volume Feature allows you to select a single device that the volume buttons always control. For example, the remote can be in TV mode while the volume buttons control the volume on your audio receiver or sound bar instead of your TV. setup tv 1 2 tv 3 4 5 7 1 8 Disabling the Master Volume Feature 1. Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button.
Using Your Remote Code Identification setup tv 1. Press and hold down the SETUP button on the remote until the red light on the remote control turns on. Release the SETUP button. The red light will remain on. 2. Press and release the desired device button (TV, cbl) you would like the code for. 3. Press and release the ENTER button. 4. Press and release the #1 button. Count the number of times the remote light flashes. This is the number corresponding to the first digit of the code.
Troubleshooting Remote does not operate your device. • Make sure the batteries are fresh and installed correctly. • Aim the remote directly at your device, and make sure that there are no obstructions between the remote and device. • Make sure you select the appropriate device on the remote you wish to control; TV for TV and CBL for cable box. • Try programming the remote with a different code. See Direct Code Entry section. • Remote may not be compatible with your device.
90-Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
FCC Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
33700 | 33701 Control Remoto Universal Manual de Instrucciones tv cbl tv setup sleep cbl input setup 15 sleep input
Índice Introducción..................................................................................16 Configuración...............................................................................17 Funciones de los Botones.......................................................18 Programación de su Control Remoto...............................20 Entrada Directa de Códigos.............................................20 Búsqueda Automática de Códigos...............................22 Uso del Control Remoto....
Configuración El control remoto universal usa dos (2) baterías AA (no incluidas). Se recomienda usar baterías alcalinas. Instalación de las baterías 1. En la parte posterior del control remoto, presione hacia abajo sobre la superficie texturada y deslice la tapa de las baterías para quitarla. 2. Inserte dos (2) baterías AA de modo tal que las marcas (+) y (-) de las baterías coincidan con las marcas (+) y (-) en el interior del compartimento de las mismas. Asegúrese de usar baterías nuevas. 3.
Funciones de los botones 1 2 cbl tv 3 4 5 6 8 9 7 10 11 setup sleep input 12 18
Funciones de los botones 1. Encendido/Apagado - Enciende o apaga los aparatos 2. TV, cbl - Selecciona el aparato que desea controlar 3. Subir/Bajar volumen 4. Subir/Bajar canales 5. Mute - Apaga el sonido 6. Canal anterior - permite volver al canal seleccionado previamente 7. Números - Se usa para seleccionar un canal directamente 8. Punto (•) - Se usa para seleccionar los canales digitales, p. ej., 4.1 9.
Programación del control remoto Este control remoto universal marca GE está diseñado para controlar múltiples aparatos de audio/video mediante el uso de un único control remoto. Para usar este control remoto, deberá programarlo para controlar los aparatos. Hay dos formas de programar el control remoto: Entrada directa de códigos o Búsqueda automática de códigos. • La Entrada directa de códigos es el método recomendado ya que en la mayoría de los casos es el más sencillo y el más rápido.
Programación del control remoto 4. Use los botones de números del control remoto para introducir el primer código remoto de 4 dígitos que encerró en un círculo en la Lista de códigos en el Paso 1. La luz roja se apagará después de introducir el cuarto dígito. 5. Apunte el control remoto hacia el dispositivo. Pruebe los botones en el control para ver si el dispositivo responde como debería ser.
Programación del control remoto Búsqueda automática de códigos La Búsqueda automática de códigos es un proceso mediante el cual puede buscar por todos los códigos almacenados en el control remoto para encontrar un código para el dispositivo. Se recomienda que lea todos los pasos a continuación para familiarizarse con la Búsqueda automática de códigos antes de comenzar el proceso. 1. Encienda manualmente el dispositivo que desea controlar.
Programación del control remoto ¿Se apagó el dispositivo? • Si la respuesta es AFIRMATIVA, significa que ha encontrado un código para el dispositivo. Presione y suelte el mismo botón que oprimió en el Paso 3. Esta acción almacenará el código en el control remoto. Proceda al Paso 7. • Si la respuesta es NEGATIVA, siga oprimiendo y soltando el botón VOL + hasta que se apague el dispositivo para probar los otros 9 códigos del Paso 4.
Uso del control remoto Característica de volumen principal La característica de volumen maestro le permite seleccionar un solo dispositivo que siempre es controlado por los botones de volumen. Por ej., el control remoto puede estar en el modo de televisor mientras que los botones de volumen controlan el volumen del receptor de audio o la barra de sonido en lugar del televisor. Activación de la característica de volumen maestro setup tv 1.
Uso del control remoto Identificación de Códigos setup tv 1. Presione y mantenga presionado el botón SETUP (Configuración) hasta que la luz roja del control remoto se encienda. Suelte el botón SETUP. La luz roja permanecerá encendida. 2. En el control remoto, presione y suelte el botón correspondiente al aparato (TV, strm, cbl, b-ray, dvd, sat, aux, aud) para el que desee obtener el código. 3. Presione y suelte el botón ENTRAR. 4. Presione y suelte el botón n.º 1.
Resolución de problemas El control remoto no funciona con su aparato. • Asegúrese de que las pilas sean nuevas y estén bien colocadas. • Apunte a su dispositivo directamente con el control remoto, • Asegúrese de seleccionar en el control remoto el dispositivo correcto que desea controlar, por ejemplo: TV para el televisor y CBL para el receptor de cable. • Intente programar el control remoto usando un código distinto. Consulte la sección Entrada directa de códigos.
Garantía Limitada de 90 Días Jasco Products Company garantiza que este producto está libre de defectos de fabricación durante un lapso de noventa días desde la fecha de compra original del consumidor. Esta garantía está limitada a la reparación o el reemplazo de este producto solamente y no cubre los daños consecuentes o accidentales a otros productos que puedan usarse con esta unidad. Esta garantía prevalecerá sobre cualquier otra garantía expresa o implícita.
Declaración de la FCC Este dispositivo cumple con el apartado 15 de la normativa de la FCC. El funcionamiento está sujeto a las dos condiciones siguientes: (1) este dispositivo no causa interferencia negativa y (2) este dispositivo debe aceptar las interferencias recibidas, incluidas las interferencias que puedan causar un funcionamiento no deseado.