Indoor | Outdoor 45244 Home Monitoring Wired Color Camera User Manual For indoor/outdoor use. www.jascoproducts.
Table of Contents Product Features..................................................................... 3 Package Contents................................................................... 3 Choosing A Camera Mounting Location...................... 4 Testing the System................................................................. 5 Connecting to a TV................................................................. 6 Connective to a VCR or DVR...............................................
Thank you for purchasing the GE Wired Color Camera. Please review these instructions carefully before attempting to operate the unit.
3. AC adapter 4. 60 ft. camera cable (UL approved for in-wall use) 5. 3-Wire TV adapter cable 5. Adjustment wrench CHOOSING A CAMERA MOUNTING LOCATION The Wired Color Camera is designed to be mounted to a wall. It is suitable for indoor or outdoor use. When choosing a mounting location, please be advised: • This camera is designed to be reliable for outdoor use; however its flexible design allows it to be used indoors as well. It is expecially suited for viewing large areas in low or no light.
directly into the sun or any bright light, as this may cause damage to the camera. • Avoid positioning the camera so that is viewing areas where half of the area is in bright sunlight and the other half is dark, such as the shadow of a building. All types of cameras have difficulty “seeing” into areas of such divergent light levels. • In low light conditions, the camera will automatically activate its high-powered Infrared (IR) LED’s and switch the camera to Long Range Night Vision mode.
CONNECTING TO A TV The Wired Color Camera connects to the video and audio input jacks on the back of your TV, VCR or DVR. If you are not using a VCR or DVR, connect the Wired Color Camera to your TV as shown in the diagram. To view: 1. Switch on the TV; set the volume to midpoint. Note: For temporary installation you can connect the camera to the TV, VCR or DVR without using the 60 ft. extension cable. Simply connect the 3-Wire adapter cable directly to the end of the 6 ft. cable coming from the camera.
3. Select the AV input assigned to the camera on your TV by pressing the button labeled AV or VIDEO on either your TV or TV remote control. You should now be able to see and hear the output from the camera. Note: You can extend the cable using the 60 ft. extension cable at any time to optimally locate the camera (provided the cable length is sufficient). The camera cable can be extended up to 300 ft. Contact the Technical Support group (1-800-654-8483) for information reguarding adding extension cables.
To view: 1. Switch on the TV and VCR or DVR; Connect the Wired Color Camera to the VCR or DVR by connecting the 3-Wire adapter cable directly to the end of the 6 ft. cable coming from the camera. Plug in the AC adapter to the 3-wire cable and insert the yellow cable to the video jack and the white cable to the left white audio jack. You can extend the cable using the extension cable at any time to optimally locate the camera (provided the cable length is sufficient). 2.
light levels. It turns on/off the high powered InfraRed (IR) LEDs on the front of the camera. These LEDs provide artificial light that allows the camera to ‘see’ in the dark. Long Range Night Vision will appear as a Black and White image. When the image sensor detects enough light, color will return to the images.
Step 2. Cable routing -IMPORTANT (a) If running the cable along the wall surface, position cable through slot at base of mounting bracket before installing mounting bracket (see figure A). Figure A (Running cable on surface of wall) Pilot holes for mounting screws (b) If the cable needs to be ran through a wall or ceiling, then an additional hole will need to be drilled using the 3/8" drill bit. Drill the hole in the center of the three mounting screw holes (see figure B).
Step 3. Mounting bracket (a) If mounting to a stud, wood surface or other nonbrick material, use a 1/8" drill bit to drill pilot holes. Align holes in mounting bracket to drilled holes, insert screws and screw in until plate has secure fit. Do not over tighten screws. (b) If mounting to drywall or brick material, use plastic anchors (see Figure C). Using a 3/16" drill bit (masonry bit, if drilling into brick), drill holes and insert anchors into drilled holes for snug fit.
(d) Take care to position the camera in the correct orientation. To ensure the camera image is not positioned upside down, you Proper may have to rotate the camera Position housing so the light sensor is positioned below the lens. Lens Step 4. Running cable Light Sensor Run the 60' cable from the camera’s location to the location of the TV, VCR or DVR. Use the cable clips provided to keep the cable in place. (See Notes on Cable Routing) Take care not to pierce, puncture or cut the cable when securing.
Step 6. Adjusting Camera View Adjustments can now be made to the camera viewing angle. Loosening the hex head bracket nuts slightly with the hex head wrench (included). Tilt and rotate the camera head to the desired position. The camera’s universal multi-axis mount can be adjusted at different angles for ceiling or wall mount . Adjustments at these points will allow the camera to be positioned at virtually any angle. Tighten hex head nuts when completed. NOTES ON CABLE INSTALLATION 1.
SPECIFICATIONS (Subject to change without notice.) AC/DC Adapter Power supply operating voltage........................................................120V 60Hz Output voltage.......................................................................................................15V DC Output current........................................................................................................330mA Camera Camera operating voltage..................................................................
WARRANTY ONE-YEAR LIMITED WARRANTY: Jasco Products Company warrants this product to be free from manufacturing defects for a period of one year from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied.
FCC STATEMENT This device complies with part 15 of the FCC WARNING rules. Operation is subject to the following Risk of fire and shock • Only use the supplied cUL listed AC to DC adapter. two conditions: • The supplied adapter is for indoor use only. (1) This device may not cause harmful • When securing the cable, do not cut or puncture • Do not use adapter in wet locations interference. (2) This device must accept any interference received, including interference that may cause undesired operation.