Design Guide with Installation Instructions 36″ Built-In Bottom-Freezer Refrigerators monogram.
Safety Information Skill Level — Installation of this refrigerator requires basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner’s Manual for warranty information. BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT — Save these instructions for local inspector’s use. Observe all governing codes and ordinances.
Design Guide DIMENSIONS AND CLEARANCES THE INSTALLATION SPACE 35-1/2" Finished Width The finished cutout width must be 35-1/2″. 84-1/2" max 83-1/2" min Finished Opening Wall View 2-5/16" 10" 6" Electrical Area 24" Cutout Depth Water Supply 3-1/2" 3-1/2" 5" 5" 10" 25-3/8" Framed Models 25-3/4" Stainless Steel Models Case Depth 35" Case Width 3-1/2" *84" From Floor to Top Frame *83-1/2" at Rear 75" From Floor to Bottom of Electrical Area * Shipping height.
Design Guide Refrigerator Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.
Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.
Design Guide CUSTOMIZATION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Professional Style Stainless Steel Refrigerators Stainless steel wrapped refrigerators with beveled edges and professional style handles. These models are shipped ready for installation. Overlay panels You may also choose to install custom overlay panels from your cabinet manufacturer. This design provides a seamless appearance which integrates smoothly with surrounding cabinetry.
Design Guide 1/4″ FRAMED PANEL DIMENSIONS If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door, drawer and grille. 5/16" Trim Reveal Door 1/4" Panel If the custom panel is less than 1/4″ thick and if it fits loosely in the door frame, it can be backed up with a piece of filler material or foam tape to improve the fit. IMPORTANT NOTE: Maximum total panel weight: • Fresh food door panel – 58 lbs.
Design Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4″ side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. • Cut a notch in the top front corner as shown to allow clearance for corner keys in the front side trim.
Installation Instructions TOOLS REQUIRED MATERIALS REQUIRED • Tinsnips to cut banding • Stepladder • Bucket • Level • Appliance Hand Truck • Tubing cutter • 7/16″ open-end wrench • #2 Phillips screwdriver • Drill and appropriate bits • 5/16″, 7/16″ socket • Safety glasses • 1-1/4″ open end wrench • Pliers • 1/4″ ratchet • 35″ long 2x4 for Anti-Tip support • 1/4″ copper water line tubing or GE SmartConnect™ Refrigerator Tubing kits • Water shut-off valve • Custom panels for fresh food door, freezer drawer
Installation Instructions • Remove the four 7/16″ bolts securing the straps to the skid. STEP 1 REMOVE PACKAGING CAUTION: Refrigerator is much heavier at the CAUTION: DO NOT ATTEMPT TO ROLL UNIT OFF SKID. top than at the bottom—be careful when moving. When using a hand truck, handle from side only. Toekick PRUDENCE: Le réfrigérateur est beaucoup plus lourd en haut qu’en bas. Il faut être prudent lors des déplacements. Si un diable est utilisé, il faut soulever le réfrigérateur sur le côté seulement.
Installation Instructions STEP 4 INSTALL ANTI-TIP BRACKETS STEP 2A WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM WARNING: ANTI-TIP PRECAUTIONS The refrigerator is top-heavy and must be secured to prevent the possibility of tipping forward. Skip this step when not using an RO System If the water supply to the refrigerator is from a Reverse Osmosis Water System, use the refrigerator’s filter bypass plug.
Installation Instructions STEP 6 ALTERNATE ANTI-TIP PROCEDURE STEP 5 LEVEL REFRIGERATOR All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator. • To level the back of the refrigerator, turn the 7/16″ hex nut located above the front wheels. Turn clockwise to raise or counterclockwise to lower the refrigerator. • For front leveling, use a 1-1/4″ open-end wrench.
Installation Instructions STEP 8 ADJUST DOOR SWING STEP 9 INSTALL GRILLE PANEL NOTE: This refrigerator has a 2-position door stop. When space does not allow the door to swing open fully to 130°, you may change the door swing to a 90° opening. Skip this step if door opening is satisfactory for your installation situation. • Raise the grille panel to stop position. Loosen Side Trim Screw • Lift the grille panel to access the wire cover trim.
Installation Instructions Right hand models shown. Use the same instructions for left hand models. IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 10A. STEP 10 INSTALL 1/4″ FRAMED PANELS Handle Trim Door Trim Refrigerator Door Use Front Holes to Secure Trim Use Rear Holes to Secure Handle Standard supplied handle shown in 1/4″ panel position. Install door and drawer panels: • Open door to 90°. Remove the 4 Phillips head screws from the door handle. • Remove handle. Retain all screws.
Installation Instructions Right hand models shown. Use the same instructions for left hand models. STEP 10A INSTALL OVERLAY PANELS Door Trim Handle Trim Refrigerator Door Move Forward For 3/4" Panel Use Front Holes to Secure Handle Use Rear Holes to Secure Trim Supplied handle shown in the overlay panel position. Install door and drawer panels: • Open door to 90°. Remove the 4 Phillips head screws from the door handle. • Remove handle. Retain all screws. • Remove 4 screws holding trim, lift off trim.
Installation Instructions STEP 12 CONNECT POWER STEP 11 CONNECT WATER SUPPLY • Check to be sure the power cord is plugged into the receptacle. Raise Grille Panel Electrical Outlet House Water Supply Refrigerator Water Supply Master Light Switch • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. • The temperature controls are preset at 37°F for the fresh food section and 0°F for the freezer.
Installation Instructions STEP 14 INSTALL TOEKICK • Locate the supplied toekick (shipped taped to the side of the refrigerator). Install with 2 screws provided, adjust to desired height and tighten screws. • A custom toekick can be installed to match or complement the surrounding cabinetry. Use the supplied toekick as a template to cut out the notch and vent holes.
Notes 18
Notes 19
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Consumer & Industrial Pub. No. 49-60468-1 Part No. 224D1145P001 08-07 JR Appliances General Electric Company Louisville, KY 40225 ge.
