Ceiling Fan Smart Switch Installation Guide
WARNING: RISK OF ELECTRIC SHOCK This product installation requires handling 120 volt wiring. Follow each step carefully. If any concerns handling wiring, hire a qualified electrician. Ensure all work meets local and federal regulations. WARNING: This control Must Be Installed With an External Isolating Wall Control/Switch in series with the ungrounded conductor, providing an air gap as per National Electrical Code (NEC) ANSI/NFPA 70 article 404, and Canadian Electric Code, Part 1 (CEC).
Simple DIY set up STEP 1 Download the Cync App onto your smartphone STEP 2 Install your Ceiling Fan Smart Switch STEP 3 Add your Smart Switch to the Cync App For set up help, visit support.gelighting.com or call 1-844-302-2943 GE and C by GE are trademarks of General Electric Company. Used under trademark license. Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Google and other related marks and logos are trademarks of Google LLC.
Compatibility Requirements Rating 120 V AC 60 Hz Neutral wire is required (wire is usually white or grey) Ground wire is required (wire is usually green, green with a yellow stripe, or copper) Wi-Fi 802.11 b/g/n @ 2.
Let’s Do It INCLUDED Switch Faceplate Bracket/Cover Wire Labels Line 4 Wire Nuts Load Ground 4 Phillips Mounting Screws Neutral YOU’LL NEED Phillipsc S rewdriver Needle Nose Pliers (recommended) Voltage Tester (recommended)
You Got This! And we're here to help. For in-depth instructional videos and a guided tour through the installation, go to support.gelighting.com For technical support, call 1-844-302-2943 NOTE: Please make sure your system is up-todate, and you update the firmware when prompted for the best experience.
BEFORE YOU DO ANYTHING: Turn off the power! STEP 1 Turn off the power for the switch location at the circuit breaker box. ON OFF STEP 2 Test existing switch by toggling switch on/off, ensuring lights do not turn on. STEP 3 Now, follow these setup steps for a single gang switch.
Remove your old switch STEP 1 Remove the existing wall plate and switch from the wall. STEP 2 Use voltage tester on the black wires to confirm power to the switch is off (recommended). STEP 3 Before disconnecting the wires from the wall, label each with the provided wire labels. Neutral and ground wires are required. If you don’t have either wire, the Cync Ceiling Fan Smart Switch is not compatible. STEP 4 Disconnect wires and remove existing switch.
Line a Lo d Groun Neutral d Wire Labels Line Load Ground Neutral
Connect the wires STEP 1 Connect the neutral (white) wire on the switch to the neutral (white label) wire from the wall. STEP 2 The line and load wires are interchangeable. Connect either black wire on the switch to the line (black label) wire from the wall. STEP 3 Connect the other black wire on the switch to the load (black label) wire on the wall. STEP 4 Connect the ground (green) wire on the switch with the ground (green label) wire from the wall.
Load Ground Line Neutral USING WIRE NUTS 1. Insert wires into wire nut. 2. Turn wire nut clockwise. 3. Pull gently on wires to test connection.
Fit wires into wall box Load STEP 1 Ground Line Neutral Neatly push the wires back into the box, rotating the switch so it’s oriented according to the image.
Secure the switch STEP 1 Using a Phillips screwdriver and the screws provided, secure the switch to the wall until level and flush. STEP 2 Screw on the faceplate bracket, then snap the faceplate cover onto the bracket. USING EXISTING WALL PLATE (optional) The switch fits standard paddle-style wall plates. If using the existing wall plate, skip STEP 2 and reinstall your wall plate.
Turn the power back on STEP 1 ON OFF After the switch is secured and faceplate mounted, turn the power back on at the circuit breaker box. STEP 2 At the switch, the LED indicator will flash blue indicating the device is wired correctly and is in setup mode.
Light ring will flash blue until the switch is added to the Cync App. Light ring will flash red when Wi-Fi is disconnected. Light ring will not illuminate if wired incorrectly TROUBLESHOOTING IF FAN DOESN’T TURN ON: 1. Check that power to the switch is on at the breaker. 2. Turn power off at the breaker, return to the switch to confirm the wires are securely and properly wired according to the installation guide. 3. Go to gelighting.com/cync for more troubleshooting.
Enable your voice assistant SET UP VOICE CONTROL Easily connect your Smart Switch to your Amazon Alexa- or Hey Google-enabled device in the Cync App AMAZON ALEXA To set up, open the Alexa app, search for the Cync skill, follow the setup instructions. TRY THIS... Alexa, turn off the living room. Alexa, turn on the bedroom. Alexa, set fan to speed 3. HEY GOOGLE To set up, open the Hey Google or Google Home app, search for the Cync action, follow the setup instructions. TRY THIS...
Additional Information and Warnings FCC Compliance Statement Compliance Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Cet appareil est conforme à la partie 15 des r èglements de la FCC et aux normes RSS sur les appareils exempts de licence du ministère de l’Industrie du Canada. Le fonctionnement de ce produit est assujetti aux deux conditions suivantes: 1. Cet appareil ne doit pas causer d’interf érences nuisibles; 2.Cet appareil doit accepter toute interf érence reçue, y compris celles pouvant causer un fonctionnement ind ésirable.
CAUTION For supply connections, use copper wire only rated at 75C. High Voltage - Disconnect power supply before servicing Operation temperature: 0-40ºC Type 1 Enclosure IP20 Pollution Degree 2 Impulse Voltage: 2500V Type 1 action Indoor use only. MISE EN GARDE Pour les connexions d'alimentation, utilisez uniquement du fil de cuivre évalué à 75 ° C.
TM Like your new Ceiling Fan Smart Switch? Share your experience! Leave a review where you purchased the product.